OM POWER OM2200HF User manual

MADE IN SLOVAKIA
OM2200HF
SHORTWAVE POWER
AMPLIFIER
WWW.OM-POWER.COM
OM POWER, s.r.o. 93030 Báč 126
SLOVAKIA
ontact : [phone]
e-mail : om[email protected]

1
TABLE OF CONTENTS
1. GENERAL INFORMATION
1.1. Introduction ……………………………………………………………….. 4
1.2. Specification …………………………………………………………….... 4
1.2.1. Parameters …………………………………………………………………. 4
1.2.2. Protection Circuits ………………………………………………………… 4
1.2.3. Indicators ………………………………………………………………….. 5
2. SAFETY INSTRUCTIONS ……………………………………………… 5
3. GENERAL DESCRIPTION ………………………………………………. 6
3.1. HF part ……………………………………………………………………. 6
3.2. Power Supply …………………………………………………………….. 7
3.3. Safety Devices ……………………………………………………………. 8
4. INSTALLATION ………………………………………………………… 8
4.1. Grounding ………………………………………………………………… 8
4.2. Coaxial Cable …………………………………………………………....... 8
4.3. Control Cable ………………………………………………….…………... 9
4.4. Mains Supply ……………………………………………………………… 10
4.5. Cooling …………………………………………………………………….. 10
5. OPERATION ……………………………………………………………… 10
5.1. Operation Elements ……………………………………………………….. 11
5.2. Tuning of Power Amplifier …………………………………………….. 12
6. MAINTENANCE ………………………………………………………. 15
6.1. Indication of Fault Conditions …………………………………………. 15
6.2. Fuse Replacement . .………………………………………………….... 16
6.3. Tube Replacement …………………………………………………....... 16
6.4. Cleaning ……………………………………………………………...... 16

2
7. APPENDIX ……………………………………………………………... 17
7.1. Block Diagram of OM2200 HF Power Amplifier ……………...………... 17

3
1. GENERAL INFORMATION
1.1. Introduction
The OM Power model OM2200 HF is a manual tuning, full legal limit amplifier, designed for
heavy duty use on all short wave amateur bands from 1.8 to 29.7 MHz (including WARC bands)
and all modes. It is equipped with one FU728F ceramic tetrode. This type of tube can generate
output power up to 2700W.
1.2. Specification
1.2.1. Parameters
Frequency Coverage Amateur Bands 1.8 –29.7 MHz including WARC
Power Output 2200+ W in CW and SSB
2000 W in RTTY, AM and FM
Input Power usually 40 to 60W for full output power
Input Impedance 50 Ohm, VSWR < 1.5 : 1
Power Gain typically 17 dB
Output impedance 50 Ohm unbalanced
Maximum output SWR 2:1
SWR protection: automatic switching to STBY , when reflected power is
350W or higher
Intermodulation distortion 36 dB below nominal output
Suppression of harmonics < -50 dBc
Tube FU728F Ceramic tetrode
Cooler Centrifugal blower + axial blower
Power supply 230 V - 50 Hz single phase
Transformers Toroidal transformer 3.0 kVA
Parameters 485 mm x 200 mm x 455 mm [19.1” x 7.9” x 17.9”]
(width x height x depth)
Weight 30 kg ( 66.2 lb )
1.2.2. Protection Circuits
There are 8 special protection circuits used in the amplifier. They are activated when one or
more of next parameters exceed defined values or some unwanted occasion occurs.
VSWR too high
Anode current too high
Screen current too high
Grid current too high
Mistuning of PA
Hot switching protection
Soft start for protecting your fuses
“switch-on blocking “ at opened amplifier

4
1.2.3. Indicators
There are couples of LED and bar graph indicators visible on the front panel to inform you
about value of some parameters or operation status:
Bar graph indicators Power output - 50 LED
Reflected power –20 LED
Current at screen Ig2 –10 LED
Anode voltage, anode current, tuning –30 LED
LED Indicators Current at control grid (Ig1 –2 LED)
WAIT –preheating of tube (180 sec)
STBY –standby
OPR –operating condition
FAULT –failure, switching off for abt. 4 sec
2. SAFETY INSTRUCTIONS
DANGEROUS HIGH VOLTAGE!
The power amplifier is using high voltage up to 3300V DC, which is very dangerous for
human life! Read next safety instructions carefully first, before you will start to install
and operate power amplifier! NEVER VIOLATE NEXT RULES!
NEVER ALLOW CHILDREN to play around PA or to touch power amplifier or
connected cables in working condition, or to push anything into the case holes!
The amplifier contains high voltage circuits. Never turn the amplifier on without
the upper lid in place. DO NOT ATTEMPT TO SHORTOR BYPASS safety switch under
upper lid!
The OM2200 HF amplifier is neither to be used in a WET or HUMID environment
nor to be exposed to RAINFALL!
Do not turn the amplifier on without having connected the ANTENNA or properly
rated DUMMY LOAD! A hazardous HF voltage may build up on the antenna connector
after turning the amplifier on with no antenna or dummy load connected!

5
Before opening the upper lid of the amplifier make sure that power supply has been
disconnected AT LEAST 5 minutes, allowing the electrolytic capacitors to discharge fully.
Disconnect power cord from the outlet!
Make sure that all screws holding the case together are properly in place and
tightened before carrying the amplifier with the handles!
The amplifier must be installed in such a way that free flow of hot air from the tube
is allowed. The amplifier must not be installed in a constrained surrounding (i.e. tight
shelves etc.). During long operation the upper lid and the vent grid can reach high
temperature!
The amplifier must be properly grounded during operation.
During operation the amplifier must be installed in such a way that the back of the
amplifier remains accessible.
The amplifier is an A category product. In a household it can influence other electric
appliances. In such cases the user is responsible to take proper actions to mitigate this
disturbance.
Read this manual carefully. Fallow all of instructions during installation and
operation to avoid damage to the amplifier not covered by manufacturer´s warranty! Do
not attempt to perform any change of hardware or software!
3. GENERAL DESCRIPTION
3.1. HF part
In this amplifier a tetrode FU728F is used in a grounded-cathode circuit (input into control
grid). This amplifier achieves excellent linearity by the voltage stabilization of the control grid
bias and the screen voltage. The power input is given to the control grid, using a broadband
input circuit with an input impedance of 50 Ohms. This adaptable input circuitryensures a good
input SWR (better than 1.5:1) on all amateur bands.
The output of the amplifier is a Pi-L circuit. The ceramic capacitor for TUNE and LOAD are
divided. This enables the amplifier to be tuned exactly and makes it possible to easily return to
the previously set positions after band changes.

6
Top view on the opened OM2200 HF
Tetrode FU728F PWR meter Blower Switch-on board
Output Pi-L Circuit Tuning capacitor Subpanel Power supply board
3.2. Power Supply
The power supply consists of 3 kVA toroidal transformer and rectifier block. A soft start is
provided using relays and resistors.
The high anode voltage is made by combining 8 x 420 V (total 3300V DC) @ 1.5A. Each has
its own rectifier and filter. In the high voltage circuit, safety resistors are employed to protect
the amplifier against overload.
The source for screen grid is regulated byparallel stabilization with FET transistors and delivers
a voltage of 350V at 100mA.

7
The -120V for the control grid is regulated with zener diodes.
3.3. Safety Devices
Control and monitoring circuits ensure control and safetyduring malfunctions of the PA. These
are on the Control board, which is located on the chassis subpanel.
4. INSTALLATION
NOTE
Read this chapter carefully prior you will start installation. Before unpacking inspect shipping
woody container first, if it is not damaged. Keep all of packing parts for possible future
shipment. Check unpacked power amplifier. If you find some damaging, contact your dealer
immediately to keep full warranty.
During installation go step by step according to next parts.
4.1. Grounding
The amplifier has to be grounded properly! Connect the screw on the rear panel of
the amplifier to your local grounding system with a copper cable, use a cross-section of 4
mm2 at least.
Connect your transceiver to the same grounding system of your shack carefully!
Use minimum length cables and make certain that the connections are both physically and
electrically sound. With poor grounding, you may risk damaging your equipment, having
problems with TVI/BCI or your transmitted signal may be distorted.
4.2. Coaxial Cable
The output of the transceiver is to be connected to the input of the amplifier via RG58 or similar
cable. For the connection between the power amplifier and the antenna, RG213 or similar
coaxial cable suited for high power is recommended. Both the INPUT and OUTPUT SO-239
sockets with Teflon insulation is used.

8
Rear view of the amplifier OM2200 HF
AC SOCKET FUSES OUTPUT
AUX. FAN CONTROL INPUT
4.3. Control Cable
Control cable maintains TX / RX switching of the PA (TX GND). The cable is shielded. On
the side of the power amplifier a CINCH-socket is used. On the side of your transceiver you
have to use a socket suitable for this transceiver. During transmitting the middle pin is
connected to the ground.
The relays of the OM2200 HF have to be switched earlier than HF is applied (cold switching).
Modern transceivers they have a time delay between PTT switching and power output.
If you are using and older transceiver or transmitters without time delay, we
recommend to connect the PA in such a way that the transmit/receive switch (foot switch
for example) is connected with the KEY IN socket of the amplifier. The KEY OUT socket
is to be connected with the PTT socket at the transceiver.
The amplifier is equipped with safetydevices, which ensure that the output relayis not switched
under power mistakenly (hot switching).
KEY IN RCA Phono - Input signal PTT switching voltage / current 5V /2 mA)
KEY OUT RCA Phono - Output signal PTT (maximum switching of 30V / 50mA)

9
4.4. Mains Supply
Be sure you got PA with properly terminated mains cables, corresponding with your
power system’s outlet. If not, contact your dealer. In such a case you should make the
necessary changes using a licensed electrician.
Be sure that your power system is correctly wired and properly rated! To use
adequately sized and connected grounding system is also very important.
4.5. Cooling
The amplifier must be installed in such a way that free flow of hot air from the tube
is allowed. Do not obstruct air intake and exhaust areas of the PA.
The centrifugal blowers provide the necessary cooling of the amplifier, even during long
contests. The main blower is activated by switching the PA on and it is turned off when cooling
is finished (approx. 1-5 min after switching off the PA depending on the temperature of the
tube). The supplemental fan is turned on depending on the temperature of the air exiting from
the amplifier. It is switched on at 70°C and switched off at 60°C.
5. OPERATION
Before switching PA on, make sure that amplifier is grounded, antenna or dummy
load is connected, and line cord is putted to the outlet.
Before switching PA on, check all connections between PA and TCVR.
Do not turn PA on for at least 2 hours after unpacking it and locating in its operating
location. Especially when amplifier is moved from a cold place to a warm one because not
visible condensation may develop, and this could result in damage to the high voltage
circuits of the PA.

10
Never try to change antenna output during a transmission to avoid warranty loss.
NOTE
When you decide to have a short operating break, place the amplifier in the standbymode rather
than switch it off.
5.1. Operation Elements
There is couple of operational elements accessible or visible on the front panel.
BAND- Band selector switch
TUNE - Anode capacitor for tuning, tuning of higher frequencies to "0",
lower frequencies to „100“.
LOAD - Output capacitor tunes antenna load resistance to amplifier.
Capacity is low at „100“ and high at "0" on the scale.
OFF - You switch off the amplifier by pressing this button.
ON - You switch on the amplifier by pressing this button.
After 3min of warm-up delay, the amplifier will be ready for operation.
OPR/STBY „OPERATE“ sets the amplifier ready for transmit operation.
In STBY, if WAIT-LED is on or the amplifier is OFF, the amplifier
is in bypass-mode and your transceiver is directly connected to the
antenna. Maximum allowed power in bypass mode is 200 Watts.

11
RF OUTPUT Bar graph –shows output power .
REFLECTED POWER Bar graph –shows reflected power from the antenna.
Maximum level is 350W otherwise amplifier switches to
STANDBY mode.
Ig2 Bar graph –measures the current of the second grid from -20mA to
+80mA.
HV/IP/TUNE Bar graph –measure the anode voltage, anode currency or tuning of PA.
5.2. Tuning of Power Amplifier
The OM2200 HF amplifier is operated in class AB. Thus it’s possible to obtain a maximum
output power at excellent linearity. For this purpose the amplifier has to be tuned carefully.
Before starting tuning you have to check if the right antenna or a 50 Ohms load
resistance is connected at the antenna output!
The operation of a mistuned PA will cause malfunctions, the increase of gridcurrent
(the GRID-MAX-LED will light up) and problems with TVI/BCI.
The grid-current is shown with 2 LED diodes. It’s normal if the green LED is
flashing or may be shining a little bit during peak operation. If you overload the amplifier
the output power increases the grid current at very small rates and the red GRID-MAX-
LED is shining and the safety devices switch the PA to STBY. You must decrease the input
power.
In SSB mode you will have good output power if the green LED lights up a bit. The
current of screen grid is measured and shown in a Bar graph Indicator. The amplifier has
to be tuned in such a way that the current is between - 20 mA to +50 mA. At currents
beyond these values the operating point will be shifted and IM-products will be rapidly
increased. If a value of + 70mA is exceeded, the safety devices will switch the amplifier to
STBY mode.

12
1. Set the multimeter switch to the HV position
2. Set the OPR/STBY switch to the STBY position
3. Press the ON button
The amplifier is prepared for operation with the following automatic steps:
The toroidal transformer is switched on.
The cooling blower for the final tube is switched on.
The multi-meter bar graph measures the high voltage; the normal value is 3.3 kV
The WAIT LED lights up
After switching on, please confirm that the blower is operating properly. Air must
be flowing from the ventilating aperture above the tube. If there is any concern, or no air
flow, press the “OFF” button immediately!
Heating the tube takes about 150 seconds. After this time the WAIT LED goes out and the
amplifier is ready for operation.
4. Reduce the power output of your transceiver to the minimum!
5. Switch OPR/STBY to OPR position (OPR LED lights up)
6. Choose the TUNE position of multi-meter
7. Transmit (mode CW) and increase driver power to 10W
If the input power is higher than 15Wand the power amplifier is not correctly tuned,
the safety devices will switch to STBY. After switching the amplifier to STBY, the amplifier
will automatically reset and switch back to OPR mode after abt. 3 seconds.
A tuning table is delivered with the poweramplifier. Select a band with band switch and choose
the setting of “TUNE” and “LOAD” according to the table.
NOTE
Delivered tuning table was made for 50 Ohm loading of PA (dummy load). Each amplifier
should have different values depending on used frequency and used type of antenna. Make
your own table valid for your real conditions.

13
Tuning Table shows proper tuning values for 50 Ohm termination.
Band
Tune
Load
1.8
70
40
3.5
75
30
7
30
85
10
25
45
14
70
70
18
32
50
21
25
60
24
60
66
28
40
70
8. Set TUNE knob in such a way, that the TUNE-LED lights up maximum left.
9. Set LOAD in such a way, that the TUNE LED on the TUNE scale lights up under
the “V” sign. If it is possible to obtain the LOAD in 2 positions, set the position
that is more to the right.
10. Repeat tuning several times according to 8 and 9, power output should be abt. 500W
11. Increase the input power (to about 50 W) until an output power of approximately 2200W
will be reached.
12. Repeat steps 8 and 9
13. Set TUNE to maximum output power (RF POWER LED lights up maximum right)
After this procedure the amplifier is tuned correctly and ready to give 2200W output power in
all operation modes.
At optimal tuning and full output power a positive max. 50mA current goes through the second
grid. On 24 and 28 MHz bands optimal tuning can be achieved when one or two LEDs are lit
up to the left from the position “V”. If less output is desired you can simply decrease the load
of the transceiver.
Should the amplifier demonstrate any malfunctions during tuning or should it not
behave in accordance witch the description, interrupt the tuning procedure immediately
and check the amplifier! Be sure to have not done any mistakes in choosing bands or
TUNE/LOAD values! Be sure that VSWR is not higher than 2:1 and input power is LOW!
After excluding possible human mistakes you will be able to work for long time with this
amplifier!

14
6. MAINTENANCE
6.1. Indication of fault conditions
OM2200 HF has the following indication LED on the front panel:
GRID MIN - Indication of first gird current
GRID MAX - Max. First grid current exceeded
HV - Measuring of anode voltage by bar graph
IP - Measuring of anode currency by bar graph
FAULT - Fault
OPR - Amplifier in operation mode
STBY - Amplifier in standby mode
WAIT - Heating of tube after switching on the amplifier
NOTE
Should a fault condition appear during the tuning or operation of the amplifier, the safety
circuits of OM2200 HF will react. The amplifier will be turned to STBY mode. After abt. 4 sec
the control circuits will switch the amplifier back to OPR.
If the fault will repeat 3 times after each other the control circuits will turn the
amplifier to STBY. Bringing the amplifier to OPR is enabled by using the OPR/STBY
switch only.
After reaction of safety circuits, the FAULT LED will be lit up for approx. 5 sec, depending on
the nature of the fault.
Flashing LED signalizes:
IP - Anode currency exceeded
HV - Low anode voltage
FAULT - Reflected output exceeded
GRID MAX - Grid currency exceeded
- Screen currency exceeded
GRID MAX + HV - Maximum load power exceeded
GRID MAX + IP - Zero output power during tuning
HV + IP - Tuning fault, incorrect tuning of the Pi-L output circuit
In the case when your OM2200 HF amplifier is not working correctly, please contact the
manufacturer or your dealer.

15
Manufacturer’s contacts: OM POWER, s.r.o.
930 30 Báč 126
SLOVAKIA
Email: [e-mail]
6.2. Fuse Replacemeent
The user is allowed to change mains fuses (6,3 x 32mm, 20A), accesible from the rear panel,
only. In the case of interrupted fuse (fuses) inside the power amplifier, contact your dealer,
please.
6.3. Tube Replacement
In the case of vacuum tube damaging, contact the manufacturer or your dealer for ordering new
one. You will get instructuions how to change tube and how to preset proper parameters, too.
Be very careful, you will do it only on your own risk!
If you are not comfortable to replace vacuum tube itself, contact your Service Center, please.
6.4. Cleaning
To prevent damage of amplifier surfaces and plastic components do not use aggressive
chemicals for cleaning. Do not open the amplifier for cleaning. Outer surface may be safely
accomplished by using piece of soft cotton cloth moistured with clean water or window cleaner.

16
7. APPENDIX
7.1. Block Diagram of OM2200 HF Power Amplifier