Omcan CE-TW-3600 Service manual

Conveyor Oven
Model CE-TW-3600
Installation Instruction Manual
Revised - 10/10/2014
Toll Free: 1-800-465-0234
Fax: [phone]
Email: [email protected]
www.omcan.com

2
Page
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
-------------------------------------------------------------------------- 5
-------------------------------------------------------------------------------------------- 5
--------------------------------------------------------------------------------------------- 6
------------------------------------------------------------------------------------- 6 - 9
-------------------------------------------------------------------------- 10 - 16
---------------------------------------------------------------------------- 17
------------------------------------------------------------------------------------------------- 18
---------------------------------------------------------------------------- 19
Table of Contents
Section
General Information
Safety and Warranty
Technical Specications
Installation
Operation
Maintenance
Parts Breakdowns
Electrical Schematics
Notes
Warranty Registration
Model CE-TW-3600

3
General Information
Omcan Manufacturing and Distributing Company Inc. and Food Machinery of America, Inc. dba Omcan
are not responsible for any harm or injury caused due to any person’s improper or negligent use of
this equipment. The product shall only be operated by someone over the age of 18, of sound mind, and
not under the inuence of any drugs or alcohol, who has been trained in the correct operation of this
machine, and is wearing authorized, proper safety clothing. Any modication to the machine voids any
warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while
in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Omcan Fabrication et distribution Companie Limité et Food Machinery d’ Amerique, dba Omcan ne
sont pas responsables de tout dommage ou blessure causé du fait que toute personne ait utilisé
cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de plus de 18
ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour utiliser
cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication de la
machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine ou
des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan no son responsables de ningun daño o perjuicío causado por cualquier persona inadecuada o
el uso descuidado de este equipo. El producto solo podra ser operado por una persona mayor de 18
años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido entrenado
en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada. Cualquier
modicación a la máquina anúla la garantía y puede causar daños a las personas usando la máquina
mientras esta en el funcionamiento.

4
Safety and Warranty
General Information
• Disconnect power to the unit from receptacle at the end of each day.
• Do not leave the unit in operation without an attendant.
• Do not leave the unit at high temperature when not in use or during idle periods. This will cause food
particles and grease lm to carbonize and burn.
• Turning the temperature setting down will save energy. It will take only a few minutes for the unit to regain
operating temperature.
• Never immerse the unit in water as it will cause damage to the unit and the warranty will be voided.
• DO NOT CLEAN WITH WATER JETS.
• Do not touch to the handle of drawer with “HOT SURFACE” when the unit is operating.
• Variable speed and top/bottom heat control for perfect color and texture of bread, bagels, English mufns
and more.
• Extended stainless steel conveyor belt for easy loading and large warming area for higher production.
• Safe load up area with full width coated front burn guard and cool to the touch exterior.
• Smart crumb tray keeps the bread crumbs from falling under the toaster.
• Heated holding area to keep toaster at the perfect temperature.
• Hi-limit switch prevents toaster from overheating protecting critical component parts.
• Preventive maintenance for this unit consists of the recommended cleaning procedures later in the manual.
To keep your oven in its top operating condition. These steps should be performed daily, weekly or as
required.
Turn unit off, disconnect unit from power supply or turn power off at wall breaker, remove plug from
outlet.
1 YEAR WARRANTY
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros
Your new oven can cook pizzas up to 14” diameter. Pizza entry and exit openings adjustable from 1 1/2” to
3” high. The oven features variable speed, Stainless Steel conveyor belt, with quartz sheathed heater. Not
recommended for frozen pizza, please defrost rst.

5
Technical Specications
Installation
Safety and Warranty
• Place on a level and stable surface.
• Keep the unit away from ammable objects.
• Ensure that the power cord and the socket are not damaged prior to use, and socket is the correct
electrical rating for this toaster.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Product Top Heat Bottom Heat Belt Speed
Pizza 12” Blanched 300°F / 148.9°C 400°F / 204.4°C 6 minutes
Meat and Cheese Sandwich 450°F / 232.2°C 300°F / 148.9°C 4 minutes
Meatball 500°F / 260°C 350°F / 176.7°C 2 minutes
Bagel (open) 500°F / 260°C 400°F / 204.4°C 2 minutes
1 oz. cookies 200°F / 93.3°C 250°F / 121.1°C 10 minutes
Garlic Bread Lightly Seasoned 500°F / 260°C 500°F / 260°C 2 minutes
Fish Sizzle Platter 400°F / 204.4°C 500°F / 260°C 6 minutes
Amps 15 Amps
Watts 3600 W
Opening Height 3.25” / 82.6mm
Capacity Twelve - 14” / 355.6mm pizza/h
Electrical 240V / 60Hz
Maximum Temperature 250° - 260°C / 482°F - 500°F
Weight 53 lbs. / 24 kg.
Dimension (DWH) 41” x 18.5” x 15.5” / 1041.4mm x 469.9mm x 393.7mm

6
WEEKLY
CLEANING THE CONVEYOR BELT
1. Turn power switch to the OFF position. Disconnection unit from power source and allow to cool.
2. Perform daily cleaning procedures.
3. Using a damp cloth, wipe the fan guard located on the box cover under the unit. Reconnect power or turn
Figure 1
Maintenance
CLEANING
DAILY
1. Turn main power switch to the OFF position, Disconnect unit from power source and allow unit to cool.
2. Using a mild detergent, wipe exterior surfaces, clean with a damp cloth.
A. For lightly soiled build-up, clean with a damp cloth.
B. For heavily soiled build-up, use a soft damp cloth and mild detergent. DO NOT USE CORROSIVE
CLEANERS.
3. Remove the load and unload tray by lifting it out of position. Clean using mild detergent and warm water.
4. Remove each crumb tray by sliding each of them out from under the conveyor belt. Clean crumb tray by
wiping with a damp cloth and mild detergent. DO NOT use corrosive cleaners. Place trays in place prior to
putting unit back into operating.
5. Reconnect power.
Operation
1. Turn the power to FULL power.
2. Set the conveyor speed on 4.
3. Allow warm-up time of 5 to 10 minutes.
4. Place a sample product on the conveyor belt to test the setting.
A. If toasting is too light, turn conveyor speed control clockwise to a slow speed.
B. If toasting is too dark, turn conveyor control clockwise to a faster speed.

7
Maintenance
MONTHLY
REMOVAL AND CLEANING OF CONVEYOR BELT
1. Turn main power switch to the OFF position. Disconnect unit from its power source and allow to cool.
2. Perform daily and weekly cleaning procedures. Follow the step 1 in Fig 2, to remove all of the master links.
To remove, unhook each end of one link and bring the two ends together, and un-thread. Once detached,
re-hook onto itself so not to get damaged.
3. Now that the links have been unhooked, the conveyor can now be carefully removed from the oven.
Standing at one end of the oven. Starting with the end on the bottom, roll the conveyor belt until it has been
totally removed. Take careful notice being sure not to damage the heater tubes, and working it over the
drive sprockets, (see Figure 3).
4. Clean conveyor belt in deep sink, caustic cleaners may be used. For a heavy soiled conveyor belt, soak
over night in hot soapy water.
NOTE: Do not attempt to clean the heater tubes.
5. Take this opportunity to clean and remove any loose materials inside the unit. Using a mild cleaner and
damp cloth, carefully wipe the inside surfaces being sure NOT to clean the heater tubes. DAMAGE
CAN OCCUR TO THE HEATER TUBES FROM IMPROPER CLEANING. DO NOT SPRAY CLEANING
SOLUTIONS INTO OVEN CAVITY.
6. Reinstall conveyor belt by rst laying the belt along the bottom of the oven cavity making sure the hooks on
the sides are facing the inside and ends of the hooks will be pointing away from the direction of the belt so
power back on.
4. Switch the ON/OFF switch to the ON position, and turn conveyor to its fastest setting (Make sure the heater
is off).
5. With the conveyor turned on and the crumb tray in place, take a wire grill brush or dry abrasive pad, clean
the exposed surface of conveyor belt by passing the brush or pad, back and forth across the surface of the
conveyor belt as the belt moves past (Figure 1). Continue until the entire belt is clean. Make sure the crumb
tray is installed, this will minimize the amount of particles that fall into the oven.
6. When the conveyor belt is clean, take a damp cloth and wipe the conveyor, removing any loose particles
on the belt surface.
7. Remove the crumb tray by sliding it out from beneath the conveyor belt.
Clean the crumb tray by wiping with a damp cloth and mild detergent.
• Do not use corrosive cleaners.
• Do not run conveyor oven without crumb trays installed.
• Overheating to electrical components and premature failure can
occur.
• Do not immerse or let the unit stand in water.
• Do not hose down the unit or the table/counter if the unit is on the
table/counter.
• Keep away from running water.

8
Maintenance
not to catch on any internal components once put back into operating. Also,
being sure to properly align the belt over the conveyor drive sprockets shown
in Fig 3.
NOTE: The direction of the belt.
7. Next, pull one end of the conveyor belt over the top of the sprockets, (being
sure to line the links up properly with the sprockets) bring the two ends
together.
8. Reinstall the previously removed master links as shown in step 2 & 3 in
Fig.2. Unhook the last link of the conveyor, farthest away from you, and re-thread through the other end,
and reconnect back onto itself.
9. Examine the oven to assure proper installation, once satised, install crumb trays if you have not done so.
DO NOT OPERATE UNIT WITHOUT CRUMB TRAYS INSTALLED.
10. Reconnect oven to power supply and check for proper operation.
REPLACING HEATER TUBES
1. DISCONNECT POWER SOURCE.
2. Remove the top cover panel. By removing the truss head screws. Pull the top cover panel out slightly.
3. Remove each heater tube wires which are requiring replacement from its terminal block connection. One
tube at a time.
4. Remove heater tube retainer by removing retainer screws with washer.
5. Gently, pull defective heater tube out of unit.
6. Gently, put new heater tube into unit.
7. Replace heater tube retainers.
8. Reconnect the heater tube wires to the terminal block.
9. Install top cover panel.
10. Connect unit to power source and test unit for proper operation.
REPLACING FAN MOTOR
1. DISCONNECT POWER SOURCE.
2. After unit has cooled, remove the crumb tray, and turn unit over so this bottom is facing upward. Never
place unit on its side.
3. Unplug power supply cord from fan motor.
4. Remove screws which hold fan motor and grill to the control box cover and remove fan.
5. Once removed, clean fan grill and control box cover using warm soapy water.
6. Put replacement motor and grill in place and secure to control box cover with screws previously removed.
7. Reconnect power supply cord to fan motor.
8. Replace back panel and enclosure.
9. Connect unit to power source, reinstall the crumb tray and test unit for proper operation.
REPLACING BELT DRIVE MOTOR

9
Maintenance
1. DISCONNECT POWER SOURCE.
2. After unit has cooled, remove the crumb tray and turn unit over so the bottom is facing upward. Never place
unit on its side.
3. Remove the control box cover which contains the fan motor.
4. Remove the cover that will expose the drive chain and sprockets.
5. Remove the sprockets from motor shaft, using an Allen wrench and loosening the set-screw.
6. Remove the wire from terminal block connecting the drive motor to the internal wiring.
7. Remove screws holding motor in place and remove motor from unit.
8. Put new motor in place and attach loosely with mounting screws.
9. Replace sprocket on motor shaft.
NOTE: The two sprockets must line up ush with each other, so the chain does not twist any during
operating. Also the hub gets installed closest to the motor.
10. Slide motor unit the drive chain has about 1/4” slack when lightly pushed at the center of its top open run.
(See chain tensioning illustration.)
11. Tighten screw to secure motor.
12. Rewire leads.
13. At this time you may plug unit in and test for proper operation prior to reinstalling panel and turning unit
back over onto its feet.
14. If unit is working correctly, turn unit off and unplug unit completed.
15. Reinstall side panels and control box cover. Place unit back into its upright position. Reinstall the crumb
tray.
16. Connect unit to power source and test unit for proper operation.
CLEANING AIR INTAKE ONCE A WEEK
1. DISCONNECT POWER SOURCE.
2. Place unit upside down. NOTE: you may damage the heater tubes by placing unit on its side.
3. Use a vacuum cleaner and or a damp cloth to clean the air intake. The procedure should be done at least
once a week.
LUBRICATE THE CHAIN & SPROCKETS EVERY MONTHS
1. DISCONNECT POWER SOURCE.
2. Remove the panel which exposes chain drive.
3. Using an extreme pressure, synthetic chain lubricant with a temperature
range up to 400°F. Apply liberally onto chain and sprockets.
4. Replace panel, reconnect power source and test unit.

10
Parts Breakdown
Model CE-TW-3600 11387

11
Parts Breakdown
Model CE-TW-3600 11387

12
Parts Breakdown
Model CE-TW-3600 11387

13
Parts Breakdown
Model CE-TW-3600 11387

14
Parts Breakdown
Model CE-TW-3600 11387

15
Parts Breakdown
Model CE-TW-3600 11387

16
Parts Breakdown
Model CE-TW-3600 11387
Description Position Description Position Description Position
Stainless Steel Cover 1 Middle Insulation Plate 12 IIVRIKOm 32
Fan Terminal 2 Conveyor Frame 13 Indicator Light 33
Insulation Plate 3 Tray 14-16 T.O.D.36 F65 37
Front Plate 4 Protection for Conveyor 17-19 390L 120V 1000W 38-2
Rear Cover 5 Protection for Tube Element 20-22 CR-1 Thermostt 45
Drawer 6-1 Fan with Protection 23-24 PA-12 (12P) 49
Front Plate 7-1 Motor 25 Gear 11T 61
Rear Plate 8 On/Off Switch 26 Gear 17T 62
Left Plate 9 Switch Protection 27 Stainless Steel Conveyor 72
Right Plate 10 EGO Switch 250C 28-1
Base Plate 11 EGO Switch 320C 28-2

17
Model CE-TW-3600 11387
Electrical Schematics
Electrical Schematic
Model TS7000 11387
© 2013 7-30-13, E.O.E

18
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________

19
Warranty Registration
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specied below. You can also register online by visiting:
OMCAN INC.
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
www.omcan.com/warrantyregistration.html
Thank you for choosing Omcan
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Por correo en Canadá
Pour postale au Canada
For mailing in Canada
Por correo en los EE.UU.
Pour diffusion aux États-Unis
For mailing in the US
OMCAN
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
Niagara Falls, New York
USA, 14305

Over the last 60 years, Omcan has grown to become a leading supplier to the food
service industry in Canada and the USA. Our success over these many years is
directly attributed to our established relationships with all of our valued customers
and through providing them with Diverse, Dependable and Proven products.
Omcan continues to help our customers remain competitive.
With associates in North America, Europe, Asia, and South America, our global
footprint continues to expand as we hold to the principle that clients benet from
the accessibility and familiarity of our sales team. In 2013 as our geography and
brand recognition continued to grow, we changed to one name Omcan Food
Machinery.
In over 200,000 sq ft of warehouse space we stock over 2,500 quality food
equipment and supplies for the food preparation market.