OMEZ LIGHTING Titan Wash 36*4 in 1 Moving Heads User manual

OMEZ LIGHTING
Titan Wash™ 36*4in1 Moving Heads
User Instructions
OMEZ LIGHTING
11301 IRIS LN, #B
EL MONTE, CA 91731
www.omezlighting.com

2
LED Moving Head User Manual
Introduction
Unpacking: Thank you for purchasing the LED MH184 Every MH184 has been thoroughly tested
and has been shipped in perfect operating condition. Carefully check the shipping carton for
damage that may have occurred during shipping. If the carton appears to be damaged, carefully
inspect your fixture for any damage and be sure all accessories necessary to operate the unit has
arrived intact. In the case damage has been found or parts are missing, please contact the
manufacturer or your dealer for further instructions. Do not return this unit to your dealer without
first contacting.
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or
moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself;
doing so will void your manufactures warranty. In the unlikely event your unit may require service
please contact the manufacturer or your dealer.
PLEASE recycle the shipping carton when ever possible.
General Instructions
To optimize the performance of this product, please read these operating instructions carefully to
familiarize you with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit,
for future reference.
Specifications
Model: LED MH 364
Voltage: 90-250V / 50~60Hz
Working Position: Any safe working position
Colors: RGBW Color Mixing
LED display, IP20
LED: Cree high power LEDs 4in1(RGBW 10W)
Net Weight: 9Kgs
Gross Weight: 12Kgs
Packing Dimensions: 480(L) x 350(W) x 400(H) mm
Titan Wash™ 36*4in1 Moving Heads
Photometric Beam Angle Data
Standard 35° Beam Angle
LUX @1m LUX @ 2m LUX @ 3m
R 4248
2499 1315
G 8784
5167 2720
B 1422
836 440
W 11226
6604 3476
Full 25680
15106 7950

3
Features
 Multi-Colors
 Color Strobe
 Electronic Dimming 0-100%
 Built in Microphone
 DMX-512 protocol
 Master/Slave synchronization
 2 x 16 LCD operation menu with
function buttons
 Daisy Chain Units Together in DMX
Mode
Safety Precautions
 To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
 Do not spill water or other liquids into or on to your unit.
 Be sure that the local power outlet match that of the required voltage for your unit.
 Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to
remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of
electrical shock and fire in case of an internal short.
 Disconnect from main power before making any type of connection.
 Do not remove the cover under any conditions. There are no user serviceable parts inside.
 Never operate this unit when it’s cover is removed.
 Never plug this unit in to a dimmer pack.
 Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm)
between this device and a wall.
 Do not attempt to operate this unit, if it becomes damaged.
 This unit is intended for indoor use only; use of this product outdoors voids all warranties.
 During long periods of non-use, disconnect the unit’s main power.
 Always mount this unit in safe and stable matter.
 Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to the point they exit from the unit.
 Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See “Cleaning”
for details.
 Heat -The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
 The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
Set Up
Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required
voltage for your LED MH184, The model is workable in 90-250V/50~60Hz. Please make sure your unit
voltage matches the wall outlet voltage before attempting to operate you fixture.DMX Linking: To ensure
proper DMX data transmission, when using several DMX fixtures try to use the shortest cable path possible.
The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For
example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning,
at the end, or anywhere in the middle. When a fixture is assigned a DMX address of 1, the DMX controller
knows to send DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

4
Operating Instructions
Operating Modes: You can use the LED MH184 in 4 ways:
 Sound-Active mode - The unit will react to sound, chasing through the built in programs.
 Auto Mode - The unit will automatically chase through the different colors and built-in programs.
 Slave Mode – The unit will run under slave mode.
 DMX control mode - This function will allow you to control each individual fixtures traits with a standard
DMX 512 controller.
DMX Mode: Operating through a DMX controller give the user the freedom to create their own programs
tailored to their own individual needs. This function also allows you to use your fixtures as spot lights.
1. This function will allow you to control each individual fixture’s traits with a standard DMX 512 controller.
2. The LED MH184 uses 16 DMX channels (RGBW version) to operate. Please see “DMX Values and
Functions” for the DMX traits.
3. To run your fixture in DMX mode, plug in the fixture via the XLR connections to any standard DMX
controller. Set your desired DMX address following the setup specifications that come with your DMX
controller.
Touch Buttons
There four touch buttons under the LCD display: MENU, Down, Up and Enter
Normally, the LCD will display the current DMX address code of the fixture, as like
When the first line reads: “Select Menu<>”, press Menu to enter the main menu; press Up/Down to scroll in the menu or
submenu options; Press Enter to confirm your selection, and the first line will change to “Select Value <>”,At this time, press
Up/Down to change the value in the selected function. Any time press and hold Up or Down, the value will rapidly change and
stop when release. Once the value is set, press enter again to save and exit to the main menu.

5
“DMX512 Addr: 001”

6
When in Master/Slave Synchronization Mode, only one unit in a series chain can be set as the
master.

7
DMX Channels
The DMX Value below is for the RGBW version of MH184, MH1084, MH724, MH304 only.
Channel Value Functions
1 Pan 0-255 Pan, 0-540°
2 Tilt 0-255 Tilt, 0-270°
3 Pan fine 0-255 Pan fine, 0-1.8°
4 Tilt fine 0-255 Tilt fine, 0-1.8°
0-1 off
5 R
2-255 Red LED intensity
0-1 off
6 G
2-255 Green LED intensity
0-1 off
7 B
2-255 Blue LED intensity
0-1 off
8 W
2-255 White LED intensity
0 Default soft color (value 100 )
1-100 Fast to Slow
9 Soft color
101-255 Slow to Fast
0-3 Off
10 Macto 4-255 Color fade, fast to slow
0-1 Off
11 Dimmer 2-255 dimmer
0-1 Off
2-64 Strobe model1, slow to fast
65-127 Strobe model2, slow to fast
128-190 Random strobe( slow to fast)
191-253 Strobe, slow to the fast
12 Stobe
254-255 Full on
0-1 Off
13 Color close
2-255 The time color close, from short to long
0-1 Off
14 Color fade in
2-255 The time color fade in, from short to long
0-1 Off
15 Color open
2-255 The time color open, from short to long
0-1 Off
16 Color fade out
2-255 The time color fade out, from short to long

8
Chart Size:
Cleaning
Due to fog residue, smoke, and dust cleaning the internal and external optical lenses must be carried out
periodically to optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the outside casing.
2. Clean the external optics with glass cleaner and a soft cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog residue, dust,
dew).
Trouble Shooting ：Listed below are a few common problems the user may encounter, with solutions.
Unit not respond to DMX:
1. Check that the DMX cables are connected properly and are wired correctly (pin 3 is “hot”; on some
other DMX devices pin 2 may be ‘hot’). Also, check that all cables are connected to the right connectors;
it does matter which way the inputs and outputs are connected.
Unit does not respond to sound:
Quiet or high pitched sounds will not activate the unit. If problems are not resolved, contact your dealer for
service.