Omni Gym OG23 Instruction Manual

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Assembly and installation
OG10 Squat OG20 Back Extension OG23 Low Row OG24 Lat Pulldown OG30 Bench Press
OG31 Incline Bench Press OG41 Front Press OG70 Biceps Curl OG80 Triceps Press
OG81 Dip Bars OG90 Abdominal Bench OGC7 Core Rack OGFA24 Free Access
Lat Pulldown
OGFA41 Free Access
Front Press

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Movement Arm installation
Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland01/01/2021
Weight Unit installation
3.
1.
1. Weight Unit Light (1 iron plate)
Belongs to equipment: OG23
NOTE! The Weight Unit mass is
approximately 30 kg’s. Extreme
caution must be used while installing
the Weight Unit. Minimum 2 persons
are needed for the installation, or a
suitable lifting device must be used
with proper caution.
NOTE! The Weight Unit mass is
approximately 36 kg’s. Extreme
caution must be used while installing
the Weight Unit. Minimum 2 persons
are needed for the installation, or a
suitable lifting device must be used
with proper caution.
NOTE! The Weight Unit mass is
approximately 59 kg’s. Extreme
caution must be used while installing
the Weight Unit. Minimum 2 persons
are needed for the installation, or a
suitable lifting device must be used
with proper caution.
2. Weight Unit Medium (2 iron plates)
Belongs to equipment: OG24, OGFA24 and OG70
2.
OG23
OG24, OGFA24 and
OG70
OG10, OG30, OG31,
OG41, OGFA41 and OG80
3. Weight Unit Heavy (5 iron plates)
Belongs to equipment: OG10, OG30, OG31, OG41,
OGFA41 and OG80
www.omnigym.com
OG23
OG24,
OGFA24
OG10, OG30, OG31,
OG41, OGFA41,
OG70, OG80
Belongs to equipment: OG10, OG30, OG31, OG41,
OGFA41, OG70, OG80

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Concrete slab and positioning
Surface material
thickness max . 20 mm
1370 770
200
1000
2500
Concrete slab
Length 2500 mm
Width 1000 mm
Thickness 120-150 mm
• Ground frost insulation
• Rebaring
• Adequate drying time must be
ensured
Concrete slab cast
Top surface of the concrete base
must be on the ground level, max.
allowed deviation = - 20 mm to
compensate for the surface material
thickness

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Mounting Post installation
Positioning and securing the
Mounting Post
The Mounting Post shall be
positioned on the concrete slab
according to the Positioning
Diagram.
NOTE! The Post must be in upright
position, max. deviation is 2 mm /
1000 mm.
The Mounting Post must be secured
with 10 x 100 mm Galvanized or
Stainless Steel Concrete Screws.
For each Post 4 Screws and 4
washers are needed.
4 x OG6012 Concrete Screw 10 x 100
4 x OG611 Flat Washer M10

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Securing the Main Frame
Concrete slab
Make sure that the Main Frame and
the Movement Arm are properly
aligned before securing the Main
Frame to the concrete base.
If needed, loosen the Frame
aachment screws on the Mounting
Post in order to align the Frame and
the Movement Arm.
Next, secure the Main Frame to the
concrete base with Concrete Screws
as instructed on the next page and
nally tighten the Frame aachment
screws to the Upright Post as
instructed.
Securing the Main Frame
Check the Main Frame and
Movement Arm alignment as
instructed.
Secure the Main Frame to the
concrete base with 10 x 100
Galvanized or Stainless Steel
Concrete Screws.
4 Screws and 4 Washers are needed.
4 x OG612 Concrete Screw 10 x 100
4 x OG611 Flat Washer M10

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Weight unit assembly
1
remove after assembly
1
remove after assembly
OG10
remove after assembly
1
1
10
CL10
remove after assembly
Function of the sticker
Function of the sticker
1
remove after assembly
The “OG10”-sticker indicates which machine
the Weight Unit in question is applicable
The Weight Unit with sticker “1” must be installed
on the right side of the movement arm when
facing the machine.
There is a corresponding sticker on the right side
of the Mounting Post.

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Weight Unit installation
1. Detach the Weight Unit End Stop
by unscrewing 2 x OG632 M10 x 50
hex screws.
2. Li up the Weight Unit and slide
it all theway on the Movement arm
with the releaselever engaged.
Disengage the release lever
andmake sure that the Weight Unit is
secured andstable.
NOTE! The Weight Unit mass is
approximately 60 kg’s. Extreme
caution must be used while installing
the Weight Unit. Minimum 2 persons
are needed for the installation, or a
suitable liing device must be used
with proper caution.
3. Weight Unit: Heavy (5 iron plates)
4. Aach the Weight Unit End Stop
with 2 x OG632 M10 x 50 hex screws,
tightening torque is 24 Nm.
1.
3. 4.
2.

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Main Frame installation
1 x OG753 Threaded Sleeve
100 mm / d30
2 x OG607 Flat Washer M20
2 x OG609 Screw M20 x 40 / 420 Nm
Core Rack OGC7

Omnigym Oy Lintulahdenkuja 10, 00500 Helsinki, Finland
22/01/2021 omnigym.com
Commissioning Inspection
• Instruction Decal placement
• Mounting Post and Frame to concrete base aachment screws
• Main Frame to Post aachment screws
• Movement Arm aachment screws
• Weight Unit aachment screws
• Securing the aachment screws of all wooden parts
• Weight Unit End Stop aachment screws
• Weight Unit Release Lever function (all positions)
• Movement Arm Rubber Bumper aachment
• Unrestricted and smooth movement with all loading options
• Fill in and dispatch the Inspection Report
If you notice a manufacturing error in the product,
Please contact your dealer!