OmniCell G4 User manual

FingerprintScanner
& Card Reader
Guide
67-2100 Rev A
Install and Service for G4 Systems

Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
This guide is CONFIDENTIAL and designed only for Omnicell Technical personnel and/or designated
representatives.
This guide and accompanying software and/or hardware described in it are protected under copyright laws and may
not be copied, wholly or in part, without the express written consent of Omnicell, Inc. The same proprietary and
copyright notices must be attached to any permitted copies as were attached to the original documents.
Omnicell, Inc.
1201 Charleston Road
Mountain View, CA 94043
[phone]
www.omnicell.com
Omnicell and the Omnicell design mark, OmniBuyer, OmniCenter, OmniRx, OmniSupplier, SafetyMed, SafetyPak,
SafetyStock, and Sure-Med are registered trademarks. Anesthesia TT, Anesthesia Workstation, Anywhere RN,
Executive Advisor, Flexbin, Medication Surveillance, OmniDispenser, OmniLinkRx, OmniScanner, OmniTrack,
Omni TT, Open Touch, OptiFlex, OptiFlex MobileTrack, Point-to-Point Medication Safety, SecureVault, See & Touch,
SinglePointe, TempCheck, Touch & Go, vSuite, and WorkflowRx are trademarks of Omnicell, Inc. in the United States
and internationally. All other trademarks and trade names are the property of their respective owners.
Copyright 2011 Omnicell, Inc. All rights reserved.

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
iii
Table of Contents
Installing a Fingerprint Scanner on a 1-, 2-, and 3-Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Install the Fingerprint Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Installing a Fingerprint Scanner on an OmniRx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Remove the Omni Rx Keyboard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Install the Fingerprint Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Installing a Fingerprint Scanner on an AWS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Remove the AWS Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Install the Fingerprint Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Documentation Feedback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FB-1

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
1-1
Installing a Fingerprint Scanner
on a 1-, 2-, and 3-Cell
The fingerprint scanner on a 1-, 2-, and 3-cell cabinet is located on the card reader bracket and
should always be installed with the card reader bracket as a single piece.
Install the Fingerprint Scanner
1. Perform a graceful shutdown of the G4 cabinet and unplug the power cord from the back of
the unit.
2. Open the printer door.
3. Remove the filter access cover.
Figure 1-1. Remove the filter access panel

1-2 Installing a Fingerprint Scanner on a 1-, 2-, and 3-Cell
Install the Fingerprint Scanner
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
4. Use the # 2378 cam lock key to unlock the E-Box.
Figure 1-2. Unlock the eBox
5. Slide the console out until it locks into place.
6. Place the scanner and card reader bracket in place on the end of the eBox console.
Figure 1-3. Put the card reader and fingerprint scanner in place

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
Installing a Fingerprint Scanner on a 1-, 2-, and 3-Cell 1-3
Install the Fingerprint Scanner
7. Secure the fingerprint scanner bracket with the four screws provided.
Figure 1-4. Secure the scanner to the console with the four screws

1-4 Installing a Fingerprint Scanner on a 1-, 2-, and 3-Cell
Install the Fingerprint Scanner
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
8. If installing a fingerprint scanner and card reader combo, route the two USB cables through
the plastic cable clip provided on the side of the console. If only a scanner or card reader is
being installed, route the single USB cable through the plastic clip provided.
Figure 1-5. Route the cable(s) through the cable clip
9. Route the cable(s) through the clips on the top of the eBox console.
Figure 1-6. Route the cable(s) through the plastic routing clips on top of the console

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
Installing a Fingerprint Scanner on a 1-, 2-, and 3-Cell 1-5
Install the Fingerprint Scanner
10. Route the cable(s) through the two clips near the USB ports.
Figure 1-7. Route the cable(s) tough the two clips near the USB ports
11. Plug the USB cable(s) into the USB ports on the side of the eBox. The fingerprint scanner USB
ca ble should be plugged into USB0 and the card reader USB cable should be plugged into
USB1.
Figure 1-8. Plug the USB cable(s) into the USB ports
12. Push the eBox console back into the cabinet.

1-6 Installing a Fingerprint Scanner on a 1-, 2-, and 3-Cell
Install the Fingerprint Scanner
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
13. LAdd the M4x14 security screw to the top of the printer enclosure, securing it to the console
cover.
Figure 1-9. Add the M4x14 security screw
14. Lock the CT PC console into place using the #2378 key. Turn the key vertical to lock the G4
console into place.
Figure 1-10. Power on the cabinet
15. Replace the filter access panel.

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
Installing a Fingerprint Scanner on a 1-, 2-, and 3-Cell 1-7
Install the Fingerprint Scanner
16. Power on the cabinet.
17. Close the keyboard door.
18. Power up the G4 console.
19. Test the fingerprint scanner to ensure it is working properly.

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
2-1
Installing a Fingerprint Scanner
on an OmniRx
Remove the Omni Rx Keyboard
1. Perform a graceful shutdown of the OmniRx and unplug the power cord from the rear of the
unit.
2. Remove the two screws on the under side of the OmniRx G4 console that secure the keyboard.
Figure 2-1. Remove the bottom two keyboard screws

2-2 Installing a Fingerprint Scanner on an OmniRx
Remove the Omni Rx Keyboard
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
3. Remove the four screws on the keyboard tray that secure the keyboard to the console.
Figure 2-2. Remove the top four screws that secure the keyboard
4. Lift and remove the keyboard from the console. Set the keyboard aside.
Figure 2-3. Lift and remove the keyboard

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
Installing a Fingerprint Scanner on an OmniRx 2-3
Install the Fingerprint Scanner
5. Remove the nut that secures the keyboard ground cable.
Figure 2-4. Remove the keyboard ground cable nut
6. Remove the ground cable.
Install the Fingerprint Scanner
1. If there is a blank plate in place of the scanner location, remove the plate.

2-4 Installing a Fingerprint Scanner on an OmniRx
Install the Fingerprint Scanner
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
2. Ensure that the gasket around the fingerprint scanner is secure.
Figure 2-5. Ensure the gasket is secure
3. Ensure the gasket around the keyboard is secure as well.
Figure 2-6. Ensure the gasket around the keyboard is secure

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
Installing a Fingerprint Scanner on an OmniRx 2-5
Install the Fingerprint Scanner
4. Place the fingerprint scanner into place and secure it with the five screws provided. Ensure the
cable is facing toward the data cable.
Figure 2-7. Secure the fingerprint scanner to the keyboard tray
5. Plug the scanner into the USB port on the bottom of the keyboard tray.
Figure 2-8. Connect the USB cable to the extender
6. Reconnect the any cables that have been disconnected during the install of the fingerprint
scanner.

2-6 Installing a Fingerprint Scanner on an OmniRx
Install the Fingerprint Scanner
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
7. Set the keyboard in place.
8. Secure the keyboard with the screws previously removed.
9. Power on the unit and test the fingerprint scanner to ensure that it is working.

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
3-1
Installing a Fingerprint Scanner
on an AWS
Remove the AWS Keyboard
1. Remove the eight screws thatsecure the keyboard casing on the AWS or AWS G4.
Figure 3-1. Remove the eight screws that secure the keyboard casing

3-2 Installing a Fingerprint Scanner on an AWS
Remove the AWS Keyboard
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
2. If a card reader is present, remove the two innermost screws.
Figure 3-2. Remove the innermost screws on the card reader
3. Lift the keyboard from the keyboard holder.
Figure 3-3. Lift the keyboard from the keyboard enclosure
Note: Do not lift the keyboard too far from its resting place as there are cables attached to the keyboard
which need to be removed before the keyboard can fully be removed.

© 2011 Omnicell, Inc. Fingerprint Scanner & Card Reader Guide/67-2100 Rev A
Installing a Fingerprint Scanner on an AWS 3-3
Install the Fingerprint Scanner
4. Disconnect the keyboard and keypad cables.
Install the Fingerprint Scanner
1. If there is a blank plate in place of the scanner location, remove the plate.
2. Ensure that the gasket around the fingerprint scanner is secure.
Figure 3-4. Ensure the gasket is secure

3-4 Installing a Fingerprint Scanner on an AWS
Install the Fingerprint Scanner
Fingerprint Scanner & Card Reader Guide/67-2100 Rev A © 2011 Omnicell, Inc.
3. Ensure the gasket around the keyboard is secure as well.
Figure 3-5. Ensure the gasket around the keyboard is secure
4. Place the fingerprint scanner into place and secure it with the five screws provided. Ensure the
cable is facing toward the data cable.
Figure 3-6. Secure the fingerprint scanner to the keyboard tray