Omnik New Energy Omniksol-1k-TL2 User manual

User Manual
-Installation
-Operation
Omniksol-1k-TL2
Omniksol-1.5k-TL2
Omniksol-2k-TL2
Omniksol-2.5k-TL2-S
Omniksol-3k-TL2-S
Omnik New Energy Co., Ltd.

2
Catalog
1. Notes on this manual......................................................................................................... 4
1.1 Scope of Validation....................................................................................................... 4
1.2 Symbols Used............................................................................................................... 4
1.3 Target Group................................................................................................................. 5
2. Preparation........................................................................................................................ 6
2.1 Safety Instructions......................................................................................................... 6
2.2 Explanations of Symbols on Inverter............................................................................. 7
3. Product Information............................................................................................................ 8
3.1 Overview....................................................................................................................... 8
3.2 Major Characteristics ...................................................................................................10
3.3 Datasheet.....................................................................................................................11
4. Packing checklist ..............................................................................................................15
4.1 Assembly parts.............................................................................................................15
4.2 Product Appearance ....................................................................................................16
4.3 Product Identification....................................................................................................17
4.4 Further Information.......................................................................................................17
5. Installation.........................................................................................................................18
5.1 Safety...........................................................................................................................18
5.2 Mounting Instructions...................................................................................................19
5.3 Safety Clearance..........................................................................................................20
5.4 Mounting Procedure.....................................................................................................21
5.5 Safety lock....................................................................................................................23
6. Elektrické připojení............................................................................................................24
6.1 Zabezpečení ................................................................................................................24
6.2 Připojení střídavého proudu .........................................................................................24
6.3 Připojení na straně DC.................................................................................................28
6.4 Komunikační a monitorovací zařízení ..........................................................................33
7. Zobrazenía ovládání........................................................................................................34

3
7.1 LCD displej...................................................................................................................34
7.2 Uvedenído provozu.....................................................................................................35
7.3 Operace .......................................................................................................................35
7.4 Informace o stavu.........................................................................................................46
8. Komunikační parametr......................................................................................................47
8.1 Karta GPRS .................................................................................................................47
8.2 Instalace komunikační karty.........................................................................................48
8.3 Zaregistrujte se na monitorovacím místě .....................................................................51
8.4 Systém sledování připojení ..........................................................................................55
8.5 Kartu WiFi....................................................................................................................60
8.6 Nastavení sítě ..............................................................................................................61
8.7 Ethernetovákarta.........................................................................................................70
8.8 Instalace karty Ethernet ...............................................................................................72
9. Recycling and Disposal.....................................................................................................74
10. Trouble shooting...............................................................................................................75
11. Abbreviation......................................................................................................................77
12. Contact .............................................................................................................................78

4
1. Notes on this manual
1.1 Scope of Validation
The main purpose of this User’s Manual is to provide instructions and detailed
procedures for installing, operating, maintaining, and troubleshooting the following five
types of Omnik New Energy-Solar Inverters:
Omniksol-1k-TL2
Omniksol-1.5k-TL2
Omniksol-2k-TL2
Omniksol-2.5k-TL2-S
Omniksol-3k-TL2-S
Please keep this user manual all time available in case of emergency.
1.2 Symbols Used
CAUTION
CAUTION indicates a hazardous condition which, if not
avoided, can result in minor or moderate injury.
WARNING
WARNING indicates a hazardous situation which, if not
avoided, can result in death or serious injury or moderate
injury.
DANGER
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.

5
1.3 Target Group
Chapter 1, 2, 3, 4, 7, 8, 9, 10, 11 and chapter 12 are intended for anyone who is
intended to use Omnik Grid Tie Solar Inverter. Before any further action, the
operators must first read all safety regulations and be aware of the potential danger
to operate high-voltage devices. Operators must also have a complete understanding
of this device’s features and functions.
Chapter 5 and chapter 6 are only for qualified personnel who are intended to install
or uninstall the Omnik Grid Tie Solar Inverter.
NOTICE
Hereby qualified personnel means he/she has the valid
license from the local authority in:
•Installing electrical equipment and PV power systems (up to
1000 V).
•Applying all applicable installation codes.
•Analyzing and reducing the hazards involved in performing
electrical work.
•Selecting and using Personal Protective Equipment (PPE).
WARNING
Do not use this product unless it has been successfully
installed by qualified personnel in accordance with the
instructions in Chapter 5. “Installation”
NOTICE
NOTICE indicates a situation that can result in property
damage, if not avoided.

6
2. Preparation
2.1 Safety Instructions
WARNING
The installation, service, recycling and disposal of the
inverters must be performed by qualified personnel only in
compliance with national and local standards and
regulations. Please contact your dealer to get the
information of authorized repair facility for any maintenance
or repairmen. Any unauthorized actions including
modification of product functionality of any form will affect
the validation of warranty service; Omnik may deny the
obligation of warranty service accordingly.
DANGER
DANGER due to electrical shock and high voltage
DO NOT touch the operating component of the inverter, it
might result in burning or death.
TO prevent risk of electric shock during installation and
maintenance, please make sure that all AC and DC
terminals are plugged out.
DO NOT stay close to the instruments while there is severe
weather conditions including storm, lighting etc.

7
2.2 Explanations of Symbols on Inverter
Symbol
Description
Dangerous electrical voltage
This device is directly connected to public grid, thus all work to the
inverter shall only be carried out by qualified personnel.
DANGER to life due to high electrical voltage!
There might be residual currents in inverter because of large
capacitors. Wait 10 MINUTES before you remove the front lid.
NOTICE, danger!
This device directly connected with electricity generators and public
grid.
CAUTION
The PV inverter will become hot during operation; please
don’t touch the heat sink or peripheral surface during or
shortly after operation.
Risk of damage due to improper modifications. Never
modify or manipulate the inverter or other components of
the system.
NOTICE
Public utility only
The PV inverter designed to feed AC power directly into the
public utility power grid; do not connect AC output of the
device to any private AC equipment.

8
3. Product Information
3.1 Overview
Industrial Layout
Danger of hot surface
The components inside the inverter will release a log of heat during
operation, DO NOT touch aluminum housing during operating.
An error has occurred
Please go to Part 10 “Trouble Shooting” to remedy the error.
This device SHALL NOT be disposed of in residential waste
Please go to Part 9 “Recycling and Disposal” for proper treatments.
Without Transformer
This inverter does not use transformer for the isolation function.
Standards Association of Australian
The inverter complies with the requirement of the AS4777.
CE Mark
Equipment with the CE mark fulfils the basic requirements of the
Guideline Governing Low-Voltage and Electromagnetic Compatibility.
No unauthorized perforations or modifications
Any unauthorized perforations or modifications are strictly forbidden, if
any defect or damage (device/person) is occurred, Omnik shall not
take any responsibility for it.
Electrical Installation & Maintenance shall be conducted by licensed
electrician and shall comply with Australia National Wiring Rules.

9
Excellent Heat Elimination
Effective Shield For DC/AC/Communication Connections

10
3.2 Major Characteristics
Omnik inverter has following characteristics which make Omnik inverter “High Efficiency,
High Reliability, High Cost Effective Ratio”
Wide DC input voltage and current range, enables more PV panels connected.
Wide MPP voltage range ensure high yield under various weather conditions.
High MPP tracking accuracy, ensure the minimum power loses during converting.
Complete set of protection methods.
Also, following protection methods are integrated in Omnik inverter:
Internal overvoltage
DC insulation monitoring
Ground fault protection
Grid monitoring
Ground fault current monitoring
DC current monitoring
Integrated DC switch

11
3.3 Datasheet
Type
Omniksol-1k-TL2
Omniksol-1.5k-TL2
Omniksol-2k-TL2
Input (DC)
Max. PV Power
1300W
1750W
2300W
Max DC Voltage
500V
500V
500V
Nominal DC Voltage
360V
360V
360V
Operating MPPT Voltage
Range
80-360V
120-450V
120-450V
MPPT Voltage Range at
Nominal Power
150-360V
150-450V
150-450V
Start up DC Voltage
90V
150V
150V
Turn off DC Voltage
80V
120V
120V
Max. DC Current
16A
18A
18A
Max. Short Circuit Current for
each MPPT
20A
20A
20A
Number of MPP trackers
1
1
1
Number of DC Connection for
each MPPT
1
1
1
Max. inverter back feed current
to the array
0
0
0
DC Connection Type
MC4 Connector
MC4 Connector
MC4 Connector
Output (AC)
Max. AC Apparent Power
1100VA
1650VA
2200VA
Nominal AC Power
(cos phi = 1)
1000W
1500W
2000W
Nominal Grid Voltage
220V/230V/240V
220V/230V/240V
220V/230V/240V
Nominal Grid Frequency
50Hz/60Hz
50Hz/60Hz
50Hz/60Hz
Max. AC Current
5.8A
9A
11A
Maximum output fault current
8A
12A
14A
Maximum output protection
current
10A
14A
16A
Grid Voltage Range*
185-276V
185-276V
185-276V
Grid Frequency Range*
45-55Hz/55-65Hz
45-55Hz/55-65Hz
45-55Hz/55-65Hz
Power Factor
0.9i…1…0.9c
0.9i…1…0.9c
0.9i…1…0.9c
Total Harmonic Distortion
(THD)
<2%
<2%
<2%
Feed in Starting Power
30W
30W
30W
Night time Power Consumption
<1W
<1W
<1W
Standby Consumption
6W
6W
6W
AC Connection Type
Plug-in connector
Plug-in connector
Plug-in connector
Efficiency
Max. Efficiency (at 360Vdc)
97.5%
97.5%
97.5%
Euro Efficiency (at 360Vdc)
96.3%
96.5%
96.6%
MPPT Efficiency
99.9%
99.9%
99.9%

12
Type
Omniksol-1k-TL2
Omniksol-1.5k-TL2
Omniksol-2k-TL2
Safety and Protection
Protection Functions
Array ground insulation resistance monitoring Output over current protection
Residual current monitoring Surge protection
Array polarity reverse monitoring Output over/under voltage protection
Array over voltage protection Output over/under frequency protection
Anti-island protection Over temperature protection
Array over current protection Output short circuit protection
Protection Class
I (According to IEC 62103)
Overvoltage Category
PV II / Mains III (According to IEC 62109-1)
Reference Standard
Safety Standard
EN 62109, AS/NZS 3100
EMC Standard
EN 61000-6-1, EN 61000-6-3, EN 61000-6-2, EN 61000-6-4, EN61000-3-2, EN61000-3-3,
EN61000-3-11, EN61000-3-12
Grid Standard
VDE-AR-N-4105, VDE 0126-1-1, RD1699, CEI0-21, C10/11, G83/2, UTE C15-712-1, AS4777,
CQC
Physical Structure
Dimensions (WxHxD)
281x343x130mm
Weight
9.6kg
Environmental Protection
Rating
IP 65 (According to IEC 60529)
Cooling Concept
Natural convection
Mounting Information
Wall bracket
General Data
Operating Temperature Range
-25°C to +60°C(derating above 45℃)
Relative Humidity
0% to 100%, no condensation
Max. Altitude (above sea level)
2000m
Noise Level
< 40dB
Isolation Type
Transformer less
Islanding protection
Initiative, Frequency disturbance
DRM command
DRM0, DRM5, DRM6, DRM7, DRM8
Display
3 LED, Backlight, 4 x 20 Character LCD
Data Communication
Interfaces
RS485(WiFi, GPRS integrated)
Standard Warranty
5 - 25 years optional
*The AC voltage and frequency range may vary depending on specific country grid

13
Type
Omniksol-2.5k-TL2-S
Omniksol-3k-TL2-S
Input (DC)
Max. PV Power
2800W
3250W
Max DC Voltage
500V
500V
Nominal DC Voltage
360V
360V
Operating MPPT Voltage Range
120-450V
120-450V
MPPT Voltage Range at Nominal
Power
150-450V
150-450V
Start up DC Voltage
150V
150V
Turn off DC Voltage
120V
120V
Max. DC Current
18A
18A
Max. Short Circuit Current for each
MPPT
20A
20A
Number of MPP trackers
1
1
Number of DC Connection for each
MPPT
1
1
Max. inverter back feed current to
the array
0
0
DC Connection Type
MC4 Connector
MC4 Connector
Output (AC)
Max. AC Apparent Power
2750VA
3000VA
Nominal AC Power(cos phi = 1)
2500W
3000W
Nominal Grid Voltage
220V/230V/240V
220V/230V/240V
Nominal Grid Frequency
50Hz/60Hz
50Hz/60Hz
Max. AC Current
12.5A
14.0A
Maximum output fault current
15A
17A
Maximum output protection current
18A
20A
Grid Voltage Range*
185-276V
185-276V
Grid Frequency Range*
45-55Hz/55-65Hz
45-55Hz/55-65Hz
Power Factor
0.9i…1…0.9c
0.9i…1…0.9c
Total Harmonic Distortion (THD)
<2%
<2%
Feed in Starting Power
30W
30W
Night time Power Consumption
<1W
<1W
Standby Consumption
6W
6W
AC Connection Type
Plug-in connector
Plug-in connector
Efficiency
Max. Efficiency (at 360Vdc)
97.7%
97.7%
Euro Efficiency (at 360Vdc)
96.9%
97.0%
MPPT Efficiency
99.9%
99.9%

14
Type
Omniksol-2.5k-TL2-S
Omniksol-3k-TL2-S
Safety and Protection
Protection Functions
Array ground insulation resistance monitoring Output over current protection
Residual current monitoring Surge protection
Array polarity reverse monitoring Output over/under voltage protection
Array over voltage protection Output over/under frequency protection
Anti-island protection Over temperature protection
Array over current protection Output short circuit protection
Protection Class
I (According to IEC 62103)
Overvoltage Category
PV II / Mains III (According to IEC 62109-1)
Reference Standard
Safety Standard
EN 62109, AS/NZS 3100
EMC Standard
EN 61000-6-1, EN 61000-6-3, EN 61000-6-2, EN 61000-6-4, EN61000-3-2, EN61000-3-3,
EN61000-3-11, EN61000-3-12
Grid Standard
VDE-AR-N-4105, VDE 0126-1-1, RD1699, CEI0-21, C10/11, G83/2, UTE C15-712-1,
AS4777, CQC
Physical Structure
Dimensions (WxHxD)
281x343x150mm
Weight
9.9kg
Environmental Protection
Rating
IP 65 (According to IEC 60529)
Cooling Concept
Natural convection
Mounting Information
Wall bracket
General Data
Operating Temperature
Range
-25°C to +60°C(derating above 45℃)
Relative Humidity
0% to 100%, no condensation
Max. Altitude (above sea
level)
2000m
Noise Level
< 40dB
Islanding protection
Initiative, Frequency disturbance
DRM command
DRM0, DRM5, DRM6, DRM7, DRM8
Isolation Type
Transformer less
Display
3 LED, Backlight, 20 x4 Character LCD
Data Communication
Interfaces
RS485(WiFi, GPRS integrated)
Standard Warranty
5 - 25 years optional
*The AC voltage and frequency range may vary depending on specific country grid

15
4. Packing checklist
4.1 Assembly parts
After you receive the Omnik inverter, please check if there is any damage on the carton,
and then check the inside completeness for any visible external damage on the inverter
or any accessories. Contact your dealer if anything is damaged or missing.
Object
Quantity
Description
A
1
Omnik inverter
B
2 pairs
DC connector
C
1
AC connector
D
1
Wall mounting bracket
E
4
Screw (ST6×50)
F
4
Expansion tube
G
1
Installation and operating instructions
A
B
C
D
E
F
G

16
4.2 Product Appearance
Front
Object
Description
A
Removable front shield
B
LED light (3 pcs)
C
Function keys for displays and setting(4 pcs)
D
Monitoring LCD with backlighting
Bottom
A
B
C
D
A
D
B
C

17
Object
Description
A
DC switch
B
Plug connectors for DC input
C
Terminal for grid connection (AC output)
D
Communication interface(RS485/GPRS/WiFi/USB)
4.3 Product Identification
You can identify the inverter by the side name plate. Information such as type of the
inverter, as well as inverter specifications are specified on the side name plate. The
name plate is on the middle part of the right side of the inverter housing. And the
following figure is the side name plate example as on Omniksol-2k-TL2.
4.4 Further Information
If you have any further questions concerning the type of accessories or installation,
please check our website www.omnik-solar.com or contact our service hotline.

18
5. Installation
5.1 Safety
NOTICE
NOTICE due to the inappropriate or the harmonized
installation environment may jeopardize the life span of
the inverter.
Do NOT expose to direct sunlight to avoid power derating due to
increase in the internal temperature of the inverter.
Do NOT expose to rain and snow cover to enhance inverter life
time.
The installation site MUST have good ventilation condition.
DANGER
DANGER to life due to potential fire or electricity shock.
DO NOT installs the inverter near any inflammable or
explosive items.
This inverter will be directly connected with HIGH VOLTAGE
power generation device; the installation must be performed
by qualified personnel only in compliance with national and
local standards and regulations.

19
5.2 Mounting Instructions
Omnik inverter is designed for indoors and outdoors installation, Omnik suggests to
install the inverter in basement or garage where there’s no directly sunlight or rain.
Do not install in rooms where people live or where the prolonged presence of people
or animals is expected because of the noise that the inverter makes during operation.
Please mount the inverter in the direction as illustrated above.
Install the inverter in the vertical direction is recommended, with a max.15 degrees
backwards.
For the convenience of checking the LCD display and possible maintenance
activities, please install the inverter at eye level.
Make sure the wall you selected is strong enough to handle the screws and bear the
weight of the inverter.
Ensure the device is properly fixed to the wall.
It is not recommended that the inverter is exposed to the strong sunshine, because
the excess heating might lead to power reduction.
The ambient temperature of installation site should be between -25 °C and +60 °C .
Make sure the ventilation of the installation spot, not sufficient ventilation may reduce
the performance of the electronic components inside the inverter and shorten the life
of the inverter.

20
5.3 Safety Clearance
Observe the following minimum clearances to walls, other devices or objects to
guarantee sufficient heat dissipation and enough space for pulling the electronic solar
switch handle.
Direction
Minimum clearance
Above
30 cm
Below
40 cm
Sides
10 cm