Omron SYSMAC NYM12W-C1062 User manual

Industrial PC Platform
NY-series
Industrial Monitor
User's Manual
NYM15W-C100£
NYM15W-C106£
NYM12W-C100£
NYM12W-C106£
Industrial Monitor
W554-E2-03

NOTE
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or other-
wise, without the prior written permission of OMRON.
No patent liability is assumed with respect to the use of the information contained herein. Moreover,
because OMRON is constantly striving to improve its high-quality products, the information contained
in this manual is subject to change without notice. Every precaution has been taken in the preparation
of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions. Neither is
any liability assumed for damages resulting from the use of the information contained in this publica-
tion.
Trademarks
•Sysmac and SYSMAC are trademarks or registered trademarks of OMRON Corporation in Japan
and other countries for OMRON factory automation products.
•Windows is a registered trademark of Microsoft Corporation in the USA and other countries.
Other company names and product names in this document are the trademarks or registered trade-
marks of their respective companies.
Copyrights
Microsoft product screen shots reprinted with permission from Microsoft Corporation.

Introduction
Thank you for purchasing the Industrial Monitor.
This manual contains information that is necessary to use the Industrial Monitor (hereafter also named
as Monitor). Please read this manual and make sure you understand the functionality and perform-
ance of the Monitor before attempting to use it.
Keep this manual in a safe place where it will be available for reference during operation.
Intended Audience
This manual is intended for the following personnel, who must also have knowledge of electrical sys-
tems (an electrical engineer or the equivalent).
• Personnel in charge of introducing Factory Automation systems.
• Personnel in charge of designing Factory Automation systems.
• Personnel in charge of installing and maintaining Factory Automation systems.
• Personnel in charge of managing Factory Automation systems and facilities.
Applicable Products
This manual covers the following Industrial Monitor products:
Product Model
Industrial Monitor, 15.4 inch NYM15W-C100£
NYM15W-C106£
Industrial Monitor, 12.1 inch NYM12W-C100£
NYM12W-C106£
Additional Information
Refer to 1-4 Product Configuration on page 1 - 5 for configuration details.
Introduction
1
NY-series Industrial Monitor User's Manual (W554)

CONTENTS
Introduction .............................................................................................................. 1
Intended Audience...........................................................................................................................................1
Applicable Products .........................................................................................................................................1
Manual Information.................................................................................................. 7
Page Structure.................................................................................................................................................7
Special Information ..........................................................................................................................................8
Terms and Conditions Agreement.......................................................................... 9
Warranty and Limitations of Liability ................................................................................................................9
Application Considerations ............................................................................................................................10
Disclaimers ....................................................................................................................................................10
Safety Precautions................................................................................................. 11
Definition of Precautionary Information.......................................................................................................... 11
Symbols ......................................................................................................................................................... 11
Warnings........................................................................................................................................................12
Cautions.........................................................................................................................................................13
Precautions for Safe Use ...................................................................................... 14
Disassembly, Dropping, Mounting, Installation and Storage .........................................................................14
Wiring.............................................................................................................................................................14
Power Supply Design and Turning ON/OFF the Power Supply.....................................................................15
Operation .......................................................................................................................................................15
Cleaning, Maintenance and Disposal ............................................................................................................16
Precautions for Correct Use ................................................................................. 17
Storage, Installation and Mounting ................................................................................................................17
Wiring.............................................................................................................................................................17
Actual Operation and Operation ....................................................................................................................17
Cleaning and Maintenance ............................................................................................................................18
Regulations and Standards .................................................................................. 19
Conformance to EU Directives ......................................................................................................................19
Conformance to KC Standards......................................................................................................................20
Conformance to UL and CSA Standards.......................................................................................................20
Related Manuals..................................................................................................... 21
Related Industrial PC Manuals ......................................................................................................................21
Related Industrial PC Without Operating System Manuals ...........................................................................21
Related IPC Machine Controller Manuals......................................................................................................22
Related IPC RTOS Controller Manuals .........................................................................................................23
Related IPC Programmable Multi Axis Controller Manuals ...........................................................................23
Terminology and Abbreviations ........................................................................... 24
Industrial PC Platform ...................................................................................................................................24
Hardware ......................................................................................................................................................24
Software.........................................................................................................................................................24
Revision History..................................................................................................... 25
Sections in this Manual ......................................................................................... 27
CONTENTS
2NY-series Industrial Monitor User's Manual (W554)

Section 1 Overview
1-1 Intended Use ........................................................................................................................1 - 2
1-2 Hardware Features...............................................................................................................1 - 3
1-3 ID Information Label ............................................................................................................1 - 4
1-4 Product Configuration.........................................................................................................1 - 5
1-5 Industrial PC Platform Overview ........................................................................................1 - 6
1-5-1 Industrial Monitor ......................................................................................................................1 - 6
1-5-2 Industrial Box PC .....................................................................................................................1 - 7
1-5-3 Industrial Panel PC ..................................................................................................................1 - 7
Section 2 Hardware
2-1 Component Names and Functions.....................................................................................2 - 2
2-1-1 Front and Top of the Industrial Monitor .....................................................................................2 - 2
2-1-2 Bottom of the Industrial Monitor ................................................................................................2 - 3
2-2 LED Indicators......................................................................................................................2 - 4
2-2-1 Logo LED ..................................................................................................................................2 - 5
2-2-2 Status LED Indicator .................................................................................................................2 - 5
2-3 Connectors ...........................................................................................................................2 - 6
2-3-1 Power Connector ......................................................................................................................2 - 6
2-3-2 DVI-D Connector (Optional) ......................................................................................................2 - 7
2-3-3 NY Monitor Link Connector (Optional) ......................................................................................2 - 7
2-3-4 USB Type-A Connector .............................................................................................................2 - 8
2-3-5 USB Type-B Connector (Optional) ............................................................................................2 - 9
2-4 Optional Hardware .............................................................................................................2 - 10
2-4-1 DVI Cables ..............................................................................................................................2 - 10
2-4-2 USB Type-A to USB Type-B Cables .......................................................................................2 - 11
2-4-3 NY Monitor Link Cables ..........................................................................................................2 - 12
2-4-4 Power Supply ..........................................................................................................................2 - 13
Section 3 Software
3-1 Operating Systems ..............................................................................................................3 - 2
3-1-1 Touch Functionality ...................................................................................................................3 - 2
3-1-2 Determine Your Version of the Windows Operating Systems ...................................................3 - 3
3-2 Support Software .................................................................................................................3 - 4
3-2-1 Overview IPC Support Software for Windows...........................................................................3 - 4
3-2-2 Industrial Monitor Utility ............................................................................................................3 - 5
3-2-3 Industrial Monitor Brightness Utility ..........................................................................................3 - 8
3-2-4 Industrial PC Tray Utility .........................................................................................................3 - 10
3-3 Software for Developers....................................................................................................3 - 13
3-3-1 Overview IPC Developer Software for Windows.....................................................................3 - 13
3-3-2 Industrial Monitor API .............................................................................................................3 - 14
Section 4 Specifications
4-1 General Specifications .......................................................................................................4 - 2
4-1-1 Dimensions and Weight ............................................................................................................4 - 2
4-1-2 General Electrical Specifications...............................................................................................4 - 3
4-2 Connector Specifications ...................................................................................................4 - 4
4-2-1 Power Connector Specifications ...............................................................................................4 - 4
4-2-2 DVI-D Connector Specifications................................................................................................4 - 5
CONTENTS
3
NY-series Industrial Monitor User's Manual (W554)

4-2-3 NY Monitor Link Connector Specifications................................................................................4 - 7
4-2-4 USB Type-A Connector Specifications......................................................................................4 - 9
4-2-5 USB Type-B Connector Specifications....................................................................................4 - 10
4-3 Display Specifications....................................................................................................... 4 - 11
4-4 Environmental Specifications...........................................................................................4 - 12
4-4-1 Operation Environment Specifications ....................................................................................4 - 12
4-4-2 Temperature and Humidity Specifications...............................................................................4 - 13
4-4-3 Recycling Specifications .........................................................................................................4 - 14
Section 5 Installation
5-1 Unpack ..................................................................................................................................5 - 2
5-1-1 Unpack Procedure ....................................................................................................................5 - 2
5-1-2 Items Supplied ..........................................................................................................................5 - 3
5-2 Mount ....................................................................................................................................5 - 4
5-2-1 Installation Method in Control Panels........................................................................................5 - 4
5-2-2 Product Orientation ...................................................................................................................5 - 5
5-2-3 Temperature ..............................................................................................................................5 - 6
5-2-4 Humidity ....................................................................................................................................5 - 8
5-2-5 Vibration and Shock ..................................................................................................................5 - 8
5-2-6 Atmosphere...............................................................................................................................5 - 9
5-2-7 Electrical Environment ..............................................................................................................5 - 9
5-2-8 Prepare the Mounting Surface ................................................................................................5 - 14
5-2-9 Mount the Industrial Monitor....................................................................................................5 - 16
5-3 Wire .....................................................................................................................................5 - 17
5-3-1 Ground ....................................................................................................................................5 - 17
5-3-2 Wire the Power Connector ......................................................................................................5 - 24
5-4 Connect...............................................................................................................................5 - 26
5-4-1 Connector Identification ..........................................................................................................5 - 26
5-4-2 Connection Procedure ............................................................................................................5 - 27
5-5 Initial Power ON .................................................................................................................5 - 28
5-5-1 Initial Power ON Procedure.....................................................................................................5 - 28
Section 6 Operating Procedures
6-1 Touchscreen Operation.......................................................................................................6 - 2
6-2 Power ON / Power OFF / Standby.......................................................................................6 - 3
6-3 Support Software and Product Information .....................................................................6 - 4
6-4 React to Product Messages ................................................................................................6 - 5
Section 7 Maintenance
7-1 Preventive Maintenance ......................................................................................................7 - 2
7-1-1 Preventive Maintenance Schedule............................................................................................7 - 2
7-1-2 Clean the Touchscreen Surface ................................................................................................7 - 3
7-1-3 Clean the Monitor......................................................................................................................7 - 3
7-1-4 Check the Gasket Seal .............................................................................................................7 - 4
7-1-5 Keep Software Updated ............................................................................................................7 - 4
7-2 Corrective Maintenance ......................................................................................................7 - 5
7-2-1 Warning and Error Messages....................................................................................................7 - 5
7-2-2 Windows Event Viewer..............................................................................................................7 - 5
7-2-3 Correct Display Functionality when Nothing is Displayed .........................................................7 - 8
7-2-4 Correct Touchscreen Functionality............................................................................................7 - 9
CONTENTS
4NY-series Industrial Monitor User's Manual (W554)

Index
CONTENTS
5
NY-series Industrial Monitor User's Manual (W554)

CONTENTS
6NY-series Industrial Monitor User's Manual (W554)

Manual Information
This section provides information about this manual.
Page Structure
The following page structure is used in this manual.
A
B
C
C D
E
F
B
C
H
5 Installation
5 - 3
NY-series User's Manual (W555)
5-1 Unpack
5
5-1-1 Unpack Procedure
G
5-1 Unpack
This section provides details on how to unpack the Industrial Panel PC.
5-1-1 Unpack Procedure
1Check the package for damage.
If there is any visible damage:
• Take photos of the package and save them.
• Inform your supplier immediately.
2Open the package.
Ensure not to damage the contents.
3Ensure that all items are present.
Additional Information
Refer to 5-1-2 Items Supplied with the Product for the items supplied.
Note: This illustration is provided as a sample. It will not literally appear in this manual.
Item Explanation Item Explanation
A Level 1 heading E Special Information
B Level 2 heading F Manual name
C Level 3 heading G Page tab with the number of the main section
D Step in a procedure H Page number
Manual Information
7
NY-series Industrial Monitor User's Manual (W554)

Special Information
Special information in this manual is classified as follows:
Precautions for Safe Use
Precautions on what to do and what not to do to ensure safe usage of the product.
Precautions for Correct Use
Precautions on what to do and what not to do to ensure proper operation and performance.
Additional Information
Additional information to read as required.
This information is provided to increase understanding or make operation easier.
Version Information
Information on differences in specifications and functionality between different versions.
Manual Information
8NY-series Industrial Monitor User's Manual (W554)

Terms and Conditions Agreement
Warranty and Limitations of Liability
Warranty
•Exclusive Warranty
Omron’s exclusive warranty is that the Products will be free from defects in materials and workman-
ship for a period of twelve months from the date of sale by Omron (or such other period expressed
in writing by Omron). Omron disclaims all other warranties, expressed or implied.
•Limitations
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF
THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE
PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based
on infringement by the Products or otherwise of any intellectual property right.
•Buyer Remedy
Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally
shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-com-
plying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal
to the purchase price of the non-complying Product; provided that in no event shall Omron be re-
sponsible for warranty, repair, indemnity or any other claims or expenses regarding the Products un-
less Omron’s analysis confirms that the Products were properly handled, stored, installed and main-
tained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any
Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall
not be liable for the suitability or unsuitability or the results from the use of Products in combination
with any electrical or electronic components, circuits, system assemblies or any other materials or
substances or environments. Any advice, recommendations or information given orally or in writing,
are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.
Limitations of Liability
OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CON-
SEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY
WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Com-
panies exceed the individual price of the Product on which liability is asserted.
Terms and Conditions Agreement
9
NY-series Industrial Monitor User's Manual (W554)

Application Considerations
Suitability for Use
Omron Companies shall not be responsible for conformity with any standards, codes or regulations
which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buy-
er’s request, Omron will provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not sufficient for a complete
determination of the suitability of the Product in combination with the end product, machine, system, or
other application or use. Buyer shall be solely responsible for determining appropriateness of the par-
ticular Product with respect to Buyer’s application, product or system. Buyer shall take application re-
sponsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR
PROPERTY WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO
ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND IN-
STALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
Disclaimers
Performance Data
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for
the user in determining suitability and does not constitute a warranty. It may represent the result of
Omron’s test conditions, and the user must correlate it to actual application requirements. Actual per-
formance is subject to the Omron’s Warranty and Limitations of Liability.
Change in Specifications
Product specifications and accessories may be changed at any time based on improvements and oth-
er reasons. It is our practice to change part numbers when published ratings or features are changed,
or when significant construction changes are made. However, some specifications of the Product may
be changed without any notice. When in doubt, special part numbers may be assigned to fix or estab-
lish key specifications for your application. Please consult with your Omron’s representative at any
time to confirm actual specifications of purchased Product.
Errors and Omissions
Information presented by Omron Companies has been checked and is believed to be accurate; how-
ever, no responsibility is assumed for clerical, typographical or proofreading errors or omissions.
Terms and Conditions Agreement
10 NY-series Industrial Monitor User's Manual (W554)

Safety Precautions
Definition of Precautionary Information
The following notation is used in this manual to provide precautions required to ensure safe usage of
the Industrial Monitor. The safety precautions that are provided are extremely important to safety.
Always read and heed the information provided in all safety precautions.
The following notation is used.
WARNING
Indicates a potentially hazardous situation which, if not avoid-
ed, could result in death or serious injury. Additionally, there
may be severe property damage.
Caution
Indicates a potentially hazardous situation which, if not avoid-
ed, may result in minor or moderate injury, or property damage.
Symbols
The circle and slash symbol indicates operations that you must not do. The
specific operation is shown in the circle and explained in text.
This example indicates prohibiting disassembly.
The triangle symbol indicates precautions (including warnings). The specific
operation is shown in the triangle and explained in text.
This example indicates a precaution for electric shock.
The triangle symbol indicates precautions (including warnings). The specific
operation is shown in the triangle and explained in text.
This example indicates a general precaution.
The filled circle symbol indicates operations that you must do. The specific
operation is shown in the circle and explained in text.
This example shows a general precaution for something that you must do.
Safety Precautions
11
NY-series Industrial Monitor User's Manual (W554)

Warnings
WARNING
Ensure that installation and post-installation checks are performed by per-
sonnel in charge who possess a thorough understanding of the machinery
to be installed.
Do not use the input functions of the touchscreen in applications that involve
human life, in applications that may result in serious injury, or for emergency
stop switches.
Water or other liquid present on the touchscreen surface may create false
touch behavior and unexpected operation. Wipe away liquid on the
touchscreen before operation.
Disassembly and Dropping
Do not attempt to disassemble, repair, or modify the product in any way. Do-
ing so may result in malfunction or fire.
Installation
Always connect to a ground of 100 Ω or less when installing the product.
Safety Precautions
12 NY-series Industrial Monitor User's Manual (W554)

Cautions
Caution
Wiring
The product has an internal non-isolated DC power supply. Circuit ground (0
VDC) and frame ground are connected together. When connecting a non-
isolated device or a non-isolated interface to the product, take appropriate
actions to avoid communication failures or damage to the mentioned ports.
Industrial PC Platform Product Non-isolated
Device
Non-isolated
Interface
24 VDC
0 VDC
Operation
When using a system with multiple touchscreens, multiple users can per-
form simultaneous operations. Make sure that this can not result in unin-
tended actions.
Safety Precautions
13
NY-series Industrial Monitor User's Manual (W554)

Precautions for Safe Use
Disassembly, Dropping, Mounting, Installation and Storage
• Do not drop the product or subject it to abnormal vibration or shock. Doing so may result in product
malfunction or burning.
• When unpacking, check carefully for any external scratches or other damages. Also, shake the
product gently and check for any abnormal sound.
• Always use the devices specified in the relevant manual.
• The product must be installed in a control panel.
• Always install equipment that is included in the product specifications. Not doing so may result in
failure or malfunction.
• Install the product in the correct orientation and temperature according to the specifications in the
manual to prevent overheating. Not doing so may result in malfunction.
• When connecting peripheral devices to the product, ensure sufficient countermeasures against
noise and static electricity during installation of the peripheral devices.
• The mounting panel must be between 1.6 and 6.0 mm thick. Tighten the Mounting Brackets evenly
to a torque of 0.6 N·m to maintain water and dust resistance. If the tightening torque exceeds the
specified value, or the tightening is not even, deformation of the front panel may occur. Additionally,
make sure the panel is not dirty or warped and that it is strong enough to hold the product.
• Do not let metal particles enter the product when preparing the panel. Do not allow wire clippings,
shavings, or other foreign material to enter any product. Otherwise, the product burning, failure, or
malfunction may occur. Cover the product or take other suitable countermeasures, especially during
wiring work.
Wiring
• Follow the instructions in the manual to correctly perform connector wiring and insertion. Double-
check all wiring and connector insertion before turning ON the power supply.
• Always ensure connectors and cables are completely locked in place to prevent accidental discon-
nection.
• Do not bend or pull the cables beyond normal limit. Do not place heavy objects on top of the cables
or other wiring lines. Doing so may break the cables.
• Always use power supply wires with sufficient wire diameters to prevent voltage drop and burning.
Make sure that the current capacity of the wire is sufficient. Otherwise, excessive heat may be gen-
erated. When cross-wiring terminals, the total current for all the terminals will flow in the wire. When
wiring cross-overs, make sure that the current capacity of each of the wires is not exceeded.
• Use a power cable with a conductor cross-section of 0.2 mm2 to 2.5 mm2. Remove 7 mm of sheath
before connecting the wires.
• Be sure that all mounting bracket screws and cable connector screws are tightened to the torque
specified in the relevant manuals. The loose screws may result in fire or malfunction.
• Use crimp terminals for wiring.
• Observe the following precautions to prevent broken wires.
• When you remove the sheath, be careful not to damage the conductor.
• Connect the conductor without twisting the wires.
• Do not weld the conductors. Doing so may cause the wires to break with vibration.
Precautions for Safe Use
14 NY-series Industrial Monitor User's Manual (W554)

• Emergency stop circuits, interlock circuit, limit circuits, and similar safety measures must be provid-
ed in external control circuits.
•For an NY Monitor Link connection, always follow the cable type and connection method specifica-
tions in the manual. Otherwise, communications may be faulty.
Power Supply Design and Turning ON/OFF the Power Supply
• Always use a power supply that provides power within the rated range.
•Do not perform a dielectric strength test.
• Power ON after the DVI cable is connected between the host PC and the product.
• Power ON after the NY Monitor Link cable is connected between the host PC and the product.
• Always check the power supply and power connections before applying power. Incorrect power con-
nections can damage the product or cause burning.
• Always turn OFF the power supply to system before you attempt any of the following.
• Connecting cables
• Connecting or disconnecting the connectors
• Use a DC power supply with a slight voltage fluctuation that will provide a stable output even if the
input is momentarily interrupted for 10 ms. Use a DC power supply with reinforced insulation or dou-
ble insulation. The rated power supply voltage of the product is 24 VDC with an allowable range of
19.2 to 28.8 VDC.
• Do not turn ON the power supply to the product when a part of a human body or a conductive object
is touching the surface of the touchscreen. Doing so will cause the touchscreen functionality to be
disabled. Remove the conductive object and cycle the power supply to restore the touchscreen
functionality.
Operation
• Do not carry out the following operations when accessing a USB device or an SD Memory Card.
•Turn OFF the power supply of the product.
• Press the power button of the host PC.
• Remove a USB device.
• Confirm the safety of the system before using the touch panel.
• Signals from the touchscreen may not be entered if the touchscreen is pressed consecutively at
high speed. Only move on to the next operation after confirming that the product has detected the
previous input of the touchscreen.
• Do not accidentally press the touchscreen when the backlight is not lit or when the display does not
appear. Confirm the safety of the system before pressing the touchscreen.
• Do not use hard or pointed objects to operate or scrub the touchscreen, otherwise the surface of the
touchscreen may be damaged.
• Before you connect a computer to the product, disconnect the power supply plug of the computer
from the AC outlet. Also, if the computer has an FG terminal, make the connections so that the FG
terminal has the same electrical potential on the product. A difference in electrical potential between
the computer and the product may cause failure or malfunction.
• In systems with multiple screens in extended view, an interruption in the video signal of one screen
will cause all windows on that screen to be moved to the primary screen. Make sure that this situa-
tion is properly handled.
Precautions for Safe Use
15
NY-series Industrial Monitor User's Manual (W554)

Cleaning, Maintenance and Disposal
• Periodically check the installation conditions in applications where the product is subject to contact
with oil or water.
• As the rubber gasket will deteriorate, shrink, or harden depending on the operating environment, pe-
riodical inspection is necessary.
Precautions for Safe Use
16 NY-series Industrial Monitor User's Manual (W554)

Precautions for Correct Use
Storage, Installation and Mounting
• Do not operate or store the product in the following locations. Operation may stop or malfunctions
may occur.
• Locations subject to direct sunlight
• Locations subject to temperatures or humidity outside the range specified in the specifications
• Locations subject to condensation as the result of severe changes in temperature
• Locations subject to corrosive or flammable gases
• Locations subject to dust (especially iron dust) or salts
• Locations subject to exposure to water, oil or chemicals
• Locations subject to shock or vibration
• Locations outdoors subject to direct wind and rain
• Locations subject to strong ultraviolet light
• Take appropriate and sufficient countermeasures when installing the product in the following loca-
tions
• Locations subject to strong, high-frequency noise
• Locations subject to static electricity or other forms of noise
• Locations subject to strong electromagnetic fields
• Locations subject to possible exposure to radioactivity
• Locations close to power lines
• Always touch a grounded piece of metal to discharge static electricity from your body before starting
an installation or maintenance procedure.
• The backlight has a finite life and if that is exceeded, the product may fail or malfunction. Check the
brightness periodically and if necessary, replace the product.
Wiring
• Always ensure the rated supply voltage is connected to the product.
• Do not use cables exceeding the maximum specified length. Doing so may cause malfunction.
• Do not connect an AC power supply to the DC power connector.
• Never ground the 24 VDC side of the power supply. This may cause a short circuit.
Actual Operation and Operation
• The touchscreen supports 5 simultaneous touches. When the number of touches is exceeded, not
all touch points will be detected.
• The capacitive touchscreen reacts to contact on its surface. Accidental touching the surface of the
touchscreen may cause unintended behavior.
• You can operate the touchscreen even when you wear some gloves. Confirm that you can correctly
operate the touchscreen while wearing gloves prior to actual operation.
Precautions for Correct Use
17
NY-series Industrial Monitor User's Manual (W554)

Cleaning and Maintenance
• Do not use corrosive substances to clean the product.
•Turn OFF the product or disable the touchscreen for cleaning with water.
Precautions for Correct Use
18 NY-series Industrial Monitor User's Manual (W554)