Omron CX-SUPERVISIOR - GETTING STARTED V2.0 User manual

Cat. No. W08E-EN-01
CX-Supervisor
Software Release 2.0
GETTING STARTED
Cat. No. W08E-EN-01 Note: Specifications subject to change without notice.
Authorized Distributor:
Printed in Europe
Cat. No. W08E-EN-01 CX-Supervisor Software Release 2.0 GETTING STARTED

CX-Supervisor
Getting Started
Software Release 2.0

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page i
Notice
OMRON products are manufactured for use according to proper procedures by a qualified operator
and only for the purposes described in this manual.
The following conventions are used to indicate and classify precautions in this manual. Always heed
the information provided in them. Failure to heed precautions can result in injury to people or
damage to the product.
DANGER! Indicates information that, if not heeded, is likely to result in loss of life or
serious injury.
WARNING Indicates information that, if not heeded, could possibly result in loss of
life or serious injury.
Caution Indicates information that, if not heeded, could result in relatively serious
or minor injury, damage to the product, or faulty operation.
OMRON Product References
All OMRON products are capitalised in this manual. The word “Unit” is also capitalised when it
refers to an OMRON product, regardless of whether or not it appears in the proper name of the
product.
The abbreviation “PLC” means Programmable Logic Controller and is not used as an abbreviation for
anything else.

Getting Started with CX-Supervisor OMRON
Page ii Revision 2.0

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page iii
Visual Aids
The following headings appear in the left column of the manual to help you locate different types of
information.
Note: Indicates information of particular interest for efficient and convenient
operation of the product.
1, 2, 3… Indicates lists of one sort or another, such as procedures, checklists etc.
Represents a shortcut on the Toolbar to one of the options available on the
menu of the same window.
Indicates a program must be started, usually by clicking the appropriate
option under the standard Windows ‘Start’ button.


OMRON, 2007
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form, or by any means, mechanical, electronic, photocopying, recording, or
otherwise, without the prior written permission of OMRON.
All copyright and trademarks acknowledged.
No patent liability is assumed with respect to the use of the information contained herein. Moreover,
because OMRON is constantly striving to improve its high-quality products, the information
contained in this manual is subject to change without notice. Every precaution has been taken in the
preparation of this manual. Nevertheless, OMRON assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from the use of the information contained in
this publication.

Getting Started with CX-Supervisor OMRON
Page iv Revision 2.0

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page v
About this Manual
This manual describes the CX-Supervisor application and its installation.
This manual contains the following:
Getting Started. A description of CX-Supervisor installation and its use for the first time.
Basic Tutorial. A quick guide of use for the first time.
Advanced Tutorial. A detailed step by step tutorial for the key areas.
A Glossary of Terms and Index are also provided.
Warning: Failure to read and understand the information provided in this manual may result in
personal injury or death, damage to the product, or product failure. Please read each
section in its entirety and be sure you understand the information provided in the
section and related sections before attempting any of the procedures or operations
given.

Getting Started with CX-Supervisor OMRON
Page vi Revision 2.0

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page vii
TABLE OF CONTENTS
CX-Supervisor ............................................................................................................... Page
Getting Started with CX-Supervisor ............................................ 1
Welcome to CX-Supervisor........................................................................................... 1
About this Manual ......................................................................................................... 2
System Requirements .................................................................................................... 3
Installing CX-Supervisor ............................................................................................... 4
Copy Protection ............................................................................................................. 4
Starting CX-Supervisor.................................................................................................. 8
Customising CX-Supervisor Settings ............................................................................ 9
The CX-Supervisor Help System................................................................................... 9
Basic Tutorial................................................................................ 11
Advanced Tutorial........................................................................ 25
Glossary of Terms......................................................................... 49
Index............................................................................................... 53

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page 1
Getting Started with CX-Supervisor
This chapter introduces the CX-Supervisor application to a new user.
Welcome to CX-Supervisor
CX-Supervisor is dedicated to the design and operation of PC based visualisation and machine
control. It is not only simple to use for small supervisory and control tasks, but it also offers a wealth
of power for the design of the most sophisticated applications. CX-Supervisor boasts powerful
functions for a wide range of PC based HMI requirements. Simple applications can be created rapidly
with the aid of a large number of predefined functions and libraries, and even very complex
applications can be generated with a powerful programming language or VBScript. CX-Supervisor
has an extremely simple, intuitive handling and high user friendliness. Importing ActiveX®
components makes it possible to create flexible applications and extend functionality.
CX-Supervisor offers a comprehensive range of facilities for the developer and is capable of
developing solutions with the following features:
♦Operator interface to processes
♦Data acquisition and monitoring
♦Information management
♦Manufacturing control
♦Supervisory control
♦Batch sequencing
♦Continuous process control
♦Alarm monitoring and reporting
♦Material handling (monitoring and control)
♦Simulation and modelling through graphic animation
♦Data Logging
♦Error logging
♦Project Editor and cross referencing
♦Multi-lingual user interfaces
♦Report editor
♦Database Connectivity
♦Connection to OPC Servers
♦Use of ActiveX objects

Getting Started with CX-Supervisor OMRON
Page 2 Revision 2.0
♦Use of Visual Basic script and Java Script
CX-Supervisor runs on standard PC desktop computers running Microsoft Windows. CX-Supervisor
is intuitive and easy to use, and allows the developer to rapidly configure, test and debug a project.
CX-Supervisor comprises two separate executable Windows programs, CX-Supervisor Development
environment and CX-Supervisor Runtime environment. Applications are created and tested using the
development environment and then delivered as a final customer application with the runtime
environment.
The runtime-only environment may only be used for executing an application previously generated
using the development environment. It is not possible to generate a new runtime application using
the runtime environment.
Note: It is important that this copy of the CX-Supervisor software is registered on the OMRON
web site, in order to qualify for technical support and maintenance updates. OMRON will
not be able to help unless this copy has been registered.
About this Manual
This manual helps a new user get started with CX-Supervisor, by describing the software installation
and computer configuration, and by leading the user through the basics of CX-Supervisor application
programming.
Separate OMRON manuals describe the related software products; CX-Server, CX-Programmer etc.
Some small example applications are included with the CX-Supervisor software to demonstrate some
of the most useful features. These can be used to help with product familiarity.
CX-Supervisor comes with a comprehensive context-sensitive on-line help system, which is designed
to complement this manual, and provide a quick reference at any point in the CX-Supervisor
application when the manual is not to hand. This general help system uses a fast 'hypertext' system
that allows progressively more information to be obtained about any topic by selecting keywords
within the descriptive text.
Throughout this manual, it is assumed that the user has a working knowledge of Microsoft Windows,
and can:
♦Use the keyboard and mouse.
♦Select options from Windows menus.
♦Operate dialog boxes.
♦Locate, open and save data files.
♦Edit, cut and paste text.
♦Drag and drop.
♦Start programs from the “START” button.

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page 3
If Windows has not been used before, spending some time working with the Microsoft
documentation is recommended before using CX-Supervisor.
This introductory chapter deals with several important aspects of installing CX-Supervisor and setting
it up for use. It is recommended that this entire chapter be read before installing the software.
System Requirements
CX-Supervisor operates on the following hardware and operating systems:
Hardware Requirements
The following configuration is the minimum system requirements for running CX-Supervisor:
♦IBM PC compatible 600 MHz Pentium II processor or better.
♦256Mbyte of RAM minimum.
♦650Mbyte available hard disk space.
♦1024 x 768 XGA display.
♦A CD ROM drive is required in order to install the CX-Supervisor software.
Note: These are requirements when using minimum operating system. For other operating
systems consult your documentation.
The following configuration is the recommended minimum system environment for running CX-
Supervisor effectively:
♦IBM PC compatible Pentium II 1.0 GHz processor.
♦512Mbyte of RAM.
♦650Mbyte available hard disk space.
♦1024 x 768 XGA display.
Operating Systems and Environments
The operating systems on which this software should be run are:
♦Microsoft Windows 2000 (SP2)
♦Microsoft Windows XP Professional
Note: This product does not install or run on Windows NT, Windows ME, Windows98 or
Windows 95.
Note: CX-Supervisor is not guaranteed to be compatible with computers running Windows
emulation (e.g. Apple Macintosh or VMWare).

Getting Started with CX-Supervisor OMRON
Page 4 Revision 2.0
Note: Internet Explorer 5.0 or later is required to use the version of CX-Server installed with this
product
Interfaces to Hardware Communications
CX-Supervisor utilises communications driver CX-Server for direct communication with OMRON
factory automation equipment.
If it is intended for a PLC to be connected to the development computer for executing program code
and testing, one of the following is required:
♦RS-232C connection via a standard serial port on the computer (COM1 etc.)
♦RS-422 connection to a 422 serial board
♦Standard Ethernet board
♦Standard USB port
♦An OMRON Network Service Board
Refer to the appropriate hardware system manuals for full information about connecting and
configuring these devices for the environment.
Installing CX-Supervisor
The CX-Supervisor software is supplied on CD-ROM and is installed easily from within Windows.
To install CX-Supervisor, load the disk in the CD-ROM drive. The AutoRun feature should
automatically start the setup program and the installation of CX-Supervisor should take no more than
a few minutes. If this has been disabled see the README.TXT on the CD-ROM for manual
launching instructions.
After installation the text file README.HTML in the CX-Supervisor directory contains up-to-date
information about the software. Read this file for details of any changes or new features in CX-
Supervisor made since this manual was produced.
Copy Protection
CX-Supervisor is copy protected to prevent illegal use. During installation a valid License Key must
be entered. The CX-Supervisor Runtime environment has additional protection and if the protection
is not installed certain features are inaccessible. To gain access to these features the USB protection
must be installed.
Copy Protection using a USB Dongle
The Runtime copy protection method consists of a small box called a “Dongle” which is plugged into
a USB port. When CX-Supervisor is run the port is checked for a valid dongle and the program fails
if it is not present.

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page 5
Fitting a CX-Supervisor USB Dongle
Simply connect the dongle to any spare USB port of the computer noting any instructions supplied. If
there are no spare sockets a “USB Hub” device may be used to add extra sockets.
Once fitted, Windows will automatically detect the new hardware and the power light on the USB
Dongle will illuminate.
Note: Old 'USB Dongles' from previous versions cannot be used with this version. The version 2.0
Runtime can only be activated with a new version 2.0 USB Dongle which are clearly identified as
either ‘Machine Edition’ dongle or ‘PLUS’ dongle. A 'Machine Edition' dongle will only allow
projects compiled for 'Machine Edition' to run. A 'PLUS' dongle will allow both 'Machine Edition'
and 'PLUS' projects to run.
Feature Machine
Edition PLUS
ActiveX Yes Yes
VBScript Yes Yes
Recipes Yes Yes
Alarms 300 5000
Animations Yes Yes
Max no. Devices
(PLCs etc.) 15 256
OPC Connections Yes Yes
Max user defined
Points 500 8000
Max Regular
Interval Scripts 10 100
Max no. Pages 100 500
Supported
Databases MS Access
SQL, ODBC, MS
Access, MS Excel,
dBase, CSV
Activating a CX-Supervisor USB Dongle
The USB Dongle should not require any additional activation. The CX-Supervisor installation
process should correctly install and configure the required USB Dongle drivers, which should be
automatically loaded when the USB Dongle is fitted as above.
In exceptional circumstances, the CX-Supervisor USB Dongle Drivers can be
installed manually if required. The USB Dongle Driver installation shortcut can
be started from the Start button, and can be found under the Omron and CX-
Supervisor groups.

Getting Started with CX-Supervisor OMRON
Page 6 Revision 2.0
Copy Protection using a Parallel Dongle
Old parallel port 'Hardlock Dongles' from previous versions cannot be used with this version. The
version 2.0 Runtime can only be activated with a new USB Dongle..
Copy Protection using a Software Token
Old 'Software Tokens' from previous versions cannot be used with this version. The version 2.0
Runtime can only be activated with a new USB Dongle.
Starting CX-Supervisor
After the software installation the Programs option from the Start button shows a new group window
for CX-Supervisor under the OMRON heading. The software is ready to run and can be started by
clicking on the CX-Supervisor Developer icon.
When CX-Supervisor Developer is started and a new Project created, it displays a window similar to
the one shown below. When launched automatically from the installation, the Engine demo is
automatically loaded, and by default when started thereafter the last loaded project is automatically
loaded. The CX-Supervisor window offers many features to ease the process of programming, using
the mouse or keyboard or both. It is possible to configure the display for any size monitor so that as
much or as little information is visible as required, using options from the View menu. Any display
configuration changes are saved in the Windows environment, and restored next time CX-Supervisor
is run.
Use this section to become familiar with the layout of the CX-Supervisor display, and to set it up as
desired.

OMRON Getting Started with CX-Supervisor
Revision 2.0 Page 7
Customising CX-Supervisor Settings
By default CX-Supervisor shows the Workspace, Output view, Toolbar, Control bar and Status bar.
The display of these can be selected by activating the options from the View menu.
To display a toolbar, Window or the palette toolbox, click on the menu item with the mouse. A tick
next to a name indicates that it is currently displayed. CX-Supervisor saves the settings when it is
exited and restores them when it is next executed.
The CX-Supervisor Help System
CX-Supervisor comes with a detailed context-sensitive help system: at any time while using the
software, help can be obtained on the particular point currently being worked on, or on general

Getting Started with CX-Supervisor OMRON
Page 8 Revision 2.0
aspects of CX-Supervisor. This system is intended to complement the manual, by providing on-line
reference to specific functions of the software and how to use them.
There are three types of CX-Supervisor help: index, context sensitive help and status bar help. An
index of help topics can be accessed at any time by clicking Index from the Help menu. Instructions
on how to use help can be accessed by clicking Using Help from the Help menu.
Alternatively, help on the topic currently in use can be obtained by pressing <F1>. Some dialogs also
provide a Help button.
At the bottom of the CX-Supervisor screen is a general status bar, which provides several helpful
pieces of information as the mouse is moved over display components.
CX-Supervisor also includes “point and click” help. To use this facility click on
the icon. The cursor changes to an arrow with a question mark next to it. Use
this cursor to point at any menu item or button on the display, and then click.
Context-sensitive help for that item is then displayed.
General information regarding CX-Supervisor can be obtained by selecting About CX-Supervisor
from the Help menu.

OMRON Basic Tutorial
Revision 2.0 Page 9
Basic Tutorial
This chapter illustrates how to create a simple application using CX-Supervisor. It should only take about 20
minutes and should explain some key concepts:
•The difference between the Development and Runtime applications.
•The system is wholly controlled by data in the points, whether in memory or from a PLC
•Controls can set the data
•Graphical controls use Animations to control how the data is displayed
Introduction
This chapter describes how a simple traffic signal is drawn using the Graphics Editor and how it is
animated via the Animation Editor so that it changes colour −just as if it were a real traffic signal
controlling a road or rail junction.
As the first tutorial proceeds, important concepts about CX-Supervisor are introduced by this
symbol.
By the end of this tutorial, sufficient understanding of CX-Supervisor should have been gained to
allow progression to the second, more advanced tutorial which demonstrates some of the more
popular key features.
Note: CX-Supervisor uses standard Microsoft Windows dialogs and conventions wherever
possible so that experienced Windows users should immediately feel comfortable.
Inexperienced Windows users should refer to standard Windows documentation.
The First Step
Before the tutorial can be started, the development version of CX-Supervisor must be installed on a
suitable machine, as described earlier in this manual. When this has been done, invoke CX-
Supervisor Development from the Start button.
When CX-Supervisor has initialised, the main screen is displayed as shown (or similar):