One Forall ONE FOR ALL URC3110 User manual

Distributed by: Audiovox Accessories Corporation
111 Congressional Blvd., Suite 350
Carmel, IN 46032
* May not work with all models of all brands listed.
* Quizá no funcione con todos los modelos de todas
las marcas que aparecen en la lista.
LIMITED
LIFETIME
WARRANTY
LIMITED
LIFETIME
WARRANTY
Works With
All Major
Brands*
Works With All
Major Brands*
Works with all
major brands*
Works with all major brands*

2
TABLE OF CO TE TS
Introduction ..............................................................3
Features And Functions ...................................................4
KeyCharts..............................................................4
Installing Batteries........................................................5
Setting Up Your Components ..............................................5
Programming T / CR Combo Control ......................................6
Programming T /D D Combo Control ......................................6
Searching For Your Code...................................................7
Checking The Codes ......................................................7
Re-Assigning Device Keys .................................................7
Changing olume Lock ...................................................8
ToChange olumeLockToAnotherMode......................................8
Unlocking olumeControl..................................................8
Troubleshooting ..........................................................9
Instructions To The User .................................................10
Limited Lifetime Warranty ................................................10
Additional Information ...................................................11
Manufacturer’s Codes ....................................................12
SetupCodesForCableBoxes..............................................12
Setup Codes For Cable Box / P R (or D R) Combos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SetupCodesForSatelliteReceiver..........................................12
Setup Codes For Satellite Receiver / P R (or D R) Combos. . . . . . . . . . . . . . . . . . . . . . . 12
SetupCodesForT s.....................................................13
SetupCodesFor CRs....................................................14
SetupCodesForP Rs(orD Rs) ...........................................15
SetupCodesForT / CRCombos...........................................16
SetupCodesForD DPlayers..............................................16
Setup Codes For D D Players / CR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
SetupCodesForT /D DPlayerCombos .....................................17
Setup Codes For T / CR/D D Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

I TRODUCTIO
The One For All 3 Devices Universal Remote Control is designed to
operate three home entertainment devices,depending on the model
purchased (see Key Charts, Mode Keys on the right).
The remote control requires two fresh AAA alkaline batteries (not included)
and easy programming to control your devices.For best results,please
read and perform all instructions listed here.Also,keep these instructions
for future reference.
3

4
FEATURES A D FU CTIO S
Use the Key Charts to learn how to use the universal functions of the One For
All 3 Devices Universal Remote Control.
Key Charts
The LED (red light) blinks to show that the
remote control is working and is sending
signals.
Use SET for all programming sequences.
Press POWER once to turn on or off the
selected device.
Device Keys for 3 Devices:
Press VCR/DVD, CBL/SAT, or TV once to select a
home entertainment device to control.
Press SLEEP to activate your device’s sleep
timer (not available for all devices).
Use TV/VID to switch the TV’s input to view TV
or video program.
Use the keypad (0~9) to directly select chan-
nels (for example,09 or 31).
Press E TER once after entering channel
numbers on some TV models.
Press PREV CH once to recall the last-viewed
channel and to page back one screen on the
main menu.
Press MUTE once to turn sound off or on.
Use ME U (or EXIT)to choose options (or exit)
from your selected device’s menu or guide.
Use CH+ (or CH -) to select the next higher(or
lower) channel.
Use VOL+ (or VOL-) to raise (or lower) the
sound volume.
When controlling a DVD player, use SKIP FOR-
WARD to next DVD chapter.,use SKIP REVERSE
to the last DVD chapter.
Press SHIFT and use the Up/Down/Left/ Right
cursor keys to move the cursor in the pro-
gram guide and menu screens.
Press SHIFT and MUTE to select a menu item.
Use the transport keys to control yourVCR,
CD or DVD player,or VOD.To record a
program,press the record key (REC) twice.

I STALLI G BATTERIES
1. On the remote control’s back,push the tab and lift off the battery
cover.
2. Obtain two (2) new AAA alkaline batteries.Match the + and –
marks on the batteries to the + and – marks in the battery case,
then insert the new batteries.
3. Press the battery cover back into place.The tab should click when
the cover is locked.
4. Test the unit by pressing POWER and any mode key (e.g.,TV). f the
batteries are inserted correctly,the LED will blink once.
NOTE: When batteries need replacement, the remote control will stop operating.
Remove the old batteries and insert new ones within 30 minutes to ensure all of
your programming information is restored.
Battery Precautions: Do not mix old and new batteries.• Do not mix alkaline, stan-
dard (carbon-zinc) or rechargeable (nickelcadmium)batteries.• Always remove old,
weak or worn-out batteries promptly and recycle ordispose of them in accordance with
Local and National Regulations.
SETTI G UP YOUR COMPO E TS
The One For All 3 Devices remote control is preprogrammed at the fac-
tory to operate an RCA TV and VCR,a Motorola (G ) cable box, and a
Toshiba DVD player.To control devices other than the default brands,
perform the following steps; otherwise skip this section:
NOTE: For T / CR Combo control, see the next section.
1. Turn on a device (e.g.,VCR) and, if applicable, insert media, (e.g.,
cassette or disc).
NOTE: Please read steps 2-4 completely before proceeding.Highlight or write
down the codes and device you wish to program before moving on to step 2.
2. On the remote control,press a device key once (i.e., VCR/DVD,
CBL/SAT,or TV).Press and hold SET until the LED blinks twice,
then release SET.
3. Use the Manufacturer’s Codes (starting on page 11) to locate the
type of device and brand name and then enter the first four-digit
code for your component. f performed correctly, the LED will blink
twice.
5

NOTE: If the LED did not blink twice,then repeat steps 2 through 3 and try
entering the same code again.
4. Aim the remote control at the device and press POWER once.
The device should turn off. f it does not respond,repeat
steps 2-3,trying each code for your brand until you find one
that works. f it still does not work,try Searching For Your
Code.
NOTE: If the device does not have a POWER key, press the (PLAY) key.
5. Repeat steps 1 through 4 for each device you want to control.
PROGRAMMI G TV/VCR COMBO CO TROL
Perform the following instructions to control a TV/VCR Combo:
1. Turn on the TV/VCR Combo and insert a video cassette.
NOTE: Please read steps 2-4 completely before proceeding.Highlight or write
down the codes and device you wish to program before moving on to step 2.
2. On the remote control,press VCR/DVD.Press and hold SET until
the LED blinks twice,then release SET.
3. Use the Setup Codes For T / CR Combos (on page 12) to locate the
brand name and then enter the first four-digit code for your device.
f performed correctly, the LED will blink twice.
NOTE: If the LED did not blink twice,then repeat steps 2 through 3 and try
entering the same code again.
4. Aim the remote control at the device and press POWER once.
t should turn off. f the device does not respond,repeat
steps 2-3,trying each code for your brand until you find one
that works. f it still does not work,try Searching For Your
Code.
NOTE: If the device does not have a POWER key, press the (PLAY) key.
PROGRAMMI G TV/DVD COMBO CO TROL
Perform the following instructions to control a TV/DVD Combo:
1. Turn on your TV/DVD and insert a disc.
2. On the remote control,press VCR/DVD.Press and hold SET
until LED blinks twice, then release SET.
3. Use the Setup Codes For T /D D Combos (on
page 12) to locate the brand name and then enter the first four-
digit code for your device. f performed correctly, the LED will blink
twice.
4. Aim the remote control at your TV/DVD and press POWER.
Your TV/DVD should turn off. f your original TV/DVD
remote control did not have a POWER key, press PLAY.Your
TV/DVD should start to play. f your TV/DVD does not
respond,repeat steps 2-4,trying each code listed for your
brand until you find the one that operates your TV/DVD.
5. Your One For All 3 Devices is now programmed to operate your
TV/DVD.Write your TV/DVD code for future reference.
Remember, if you want to use your One For All 3 Devices to operate
your TV/DVD, press theVCR/DVD key first.
6

SEARCHI G FOR YOUR CODE
f your device does not respond to the remote control after trying all
codes listed for your brand,or if your brand is not listed at all,try search-
ing for your code. For example,to search for a code for your TV:
1. On the remote control,press TV once.
2. Press and hold SET until the LED blinks twice, then release
SET.
3. Enter 9-9-1.The LED will blink twice.
4. Aim the remote control at the the TV and slowly alternate
between pressing POWER and TV. Stop when the TV turns
off.
NOTE: In the search mode, the remote control will send IR codes
from its library to the selected device, starting with the most popular
code first.
5. To lock in the code,press and hold SET until the LED blinks
twice, then release SET.
6. To search for the codes of your other devices,repeat steps 1 through
5,but substitute the appropriate device key for the device you are
searching for.
CHECKI G THE CODES
f you have set up the remote control using the Searching For Your Code
procedure, you may need to find out which four-digit code is operating
your equipment:
For example, to find out which code is operating your TV:
1. On the remote control,press TV once.
2. Press and hold SET until the LED blinks twice, then release
SET.
3. Enter 9-9-0.The LED will blink twice.
4. To view the code for the first digit,press 1once.Wait 3 seconds,
count the LED blinks (e.g., 3 blinks = 3) and write down the num-
ber.
NOTE: If a code digit is“0”,the LED will not blink.
5. Repeat step 4 three more times for remaining digits.Use 2for the
second digit, 3for the third digit,and 4for the fourth digit.
6. To check for codes of other devices, repeat steps 1 through 5,but
substitute the appropriate device key for each device you are check-
ing. As before, write down each four-digit code.
RE-ASSIG I G DEVICE KEYS
The One For All 3 Devices can be set to control a second TV,VCR,or
DVD player.
For example, to control two TVs, a VCR,and a cable box, you will need
to re-assign the unused VCR/DVD key to operate the second TV as fol-
lows:
1. On the remote control,press and hold SET until the LED
blinks twice, then release SET.
7

8
2. Enter 9-9-2.The LED will blink twice.
3. Press TV once, then press VCR/DVD once.
4. The VCR/DVD key is now ready to be programmed for your second
TV.
(see Setting Up Your Components).
To re-assign other device keys, repeat steps 1 through 4 by substituting
the key sequence from the below chart for the most popular compo-
nents:
To Re-Assign Key Sequence Perform
VCR/DVDas2ndTVkey: SET -9-9-2-TV -VCR/DVD
VCR/DVDas2ndCBLkey: SET -9-9-2-CBL/SAT -VCR/DVD
VCR/DVDas2ndSATkey: SET -9-9-2-CBL/SAT -VCR/DVD
VCR/DVD backtoVCR/DVD:SET -9-9-2-VCR/DVD -VCR/DVD
When a re-assignment is done,the LED will blink twice to confirm your
choice.At that time,you will need to program the remote control for the
new device (see Setting Up Your Components).
CHA GI G VOLUME LOCK
The One For All 3 Devices is set to control the volume of your TV in the
TV,VCR, CBL/SAT, and DVD modes. f you want the volume to be con-
trolled by a mode other than TV (e.g.,CBL/SAT),change theVolume
Lock as follows:
To Change Volume Lock To Another Mode:
1. On the remote control,press and hold SET until the LED
blinks twice, then release SET.
2. Enter 9-9-3and then press any mode key once (except
TV).The LED will blink twice.
3. Now, whenever you press VOL+, or VOL–, volume will be con-
trolled by your
mode choice.
Unlocking Volume Control:
NOTE: Perform these instructions when you want independent volume control for
each programmed device (e.g., T volume control in T mode, CBL/SAT volume
control in CBL/SAT mode, etc.)
1. On the remote control,press and hold SET until the LED
blinks twice, then release SET.
2. Enter 9-9-3and then press VOL+.The LED will blink four
times.
3. Volume will again be controlled according to its default states.

TROUBLESHOOTI G
PROBLEM: LED does not blink when you press a key.
SOLUT ON: Replace batteries with four new AAA alkaline
batteries.
PROBLEM: LED blinks when you press a key, but home enter-
tainment component does not respond.
SOLUT ON: Make sure the remote control is aimed at your home
entertainment device and is not farther than 15 feet
away.
PROBLEM: The unit does not control home entertainment devices
or commands are not working properly.
SOLUT ON: Try all listed codes for thecomponent brands being
set up. Make sure they can be operated with an
infrared remote control.
PROBLEM: TV/VCR combo does not respond properly.
SOLUT ON: Use the VCR codes for your brand.Some combo
units may require both a TV code and aVCR code
for full operation.
PROBLEM: Changing channels does not work properly.
SOLUT ON: f original remote control required pressing ENTER
to change channels,press E TER on the remote
control after entering the channel number.
PROBLEM: Tried“Search Method”and still could not find a
working code.
SOLUT ON: Clear the device key as follows: Press and hold SET
until the LED blinks twice, then release.Next enter 9
-9-2.Then press the device key to be cleared twice.
Now repeat the“Search Method.”
PROBLEM: CH + and CH - do not work for your RCA TV.
SOLUT ON: Due to RCA design (1983- 1987),only the original
remote control will operate these functions.
PROBLEM: Remote control does not turn on Sony or Sharp
TV/VCR Combo.
SOLUT ON: For power on,these products require programming
TV codes.For Sony, use TV code 0000 and VCR
code 0032.For Sharp, use TV code 0093 and VCR
code 0048.
PROBLEM: Need additional information:
SOLUT ON: • Please visit : www.oneforall.com
9

I STRUCTIO S TO THE USER
This equipment has been tested and found to comply with the limits for a
class B digital device,pursuant to part 15 of the FCC Rules.These limits are
designed to provide a reasonable protection against harmful interference in a
residential installation.This equipment generates,uses,and can radiate radio
frequency energy and if not installed and used in accordance with the
instructions,may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. f this equipment does cause harmful interference to radio or tel-
evision reception,which can be determined by turning the equipment off
and on,the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• ncrease separation between equipment and receiver.
• Connect equipment into an outlet or a circuit different from that to which
the receiver is connected.
• Consult dealer or experienced radio/TV technician for help.
LIMITED LIFETIME WARRA TY
Audiovox Electronics Corporation (the“Company”) warrants to you the original
retail purchaser of this product that should it,under normal use and conditions,
be proven defective in material or workmanship during its lifetime while you
own it,such defect(s) will be repaired or replaced (at the Company’s option)
without charge for parts and repair labor. To obtain repair or replacement within
the terms of this Warranty, the product is to be delivered with proof of warranty
coverage (e.g.dated bill of sale),specification of defect(s),transportation pre-
paid, to the Company at the address shown below. This Warranty does not cover
product purchased,serviced or used outside the United States or Canada.This
Warranty is not transferable and does not extend to costs incurred for installa-
tion, removal or reinstallation of the product.This Warranty does not apply if in
the Company’s opinion,the product has been damaged through alteration,
improper installation, mishandling, misuse, neglect, accident, or the simultane-
ous use of different battery types (e.g.alkaline,standard or rechargeable).
THE EXTENT OF THE COMPANY’S L AB L TY UNDER TH S WARRANTY S
L M TED TO THE REPA R OR REPLACEMENT PROV DED ABOVE AND, N
NO EVENT, SHALL THE COMPANY’S L AB L TY EXCEED THE PURCHASE
PR CE PA D BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities.ANY
MPL ED WARRANT ES, NCLUD NG ANY MPL ED WARRANTY OF MER-
CHANTAB L TY OR F TNESS FORA PART CULAR PURPOSE SHALL BE L M-
TED TO DURAT ON OF TH S WARRANTY. N NO CASE SHALL THE COMPA-
NY BE L ABLE FOR ANYCONSEQUENT AL OR NC DENTAL DAMAGES
WHATSOEVER.No person or representative is authorized to assume for the
Company any liability other than expressed herein in connection with the sale of
this product.Some states/provinces do not allow limitations on how long an
implied warranty lasts or the exclusion or limitation of incidental or consequen-
tial damage so the above limitations or exclusions may not apply to you.
ThisWarranty gives you specific legal rights and you may also have other
rights,which vary from state/province to state/province.U.S.A.:Audiovox
Electronics Corporation, 150 Marcus Blvd., Hauppauge,New York 11788 CANA-
DA: Audiovox Return Center, c/o Genco,6685 Kennedy Road,Unit 3, Door 16,
Mississauga,Ontario L5T 3A5Mississauga,Ontario L5T 3A5
10

ADDITIO AL I FORMATIO
ONE FOR ALL® is the registered trademark of Universal Electronics
nc. Audiovox Accessories Corporation is the Licensee of the ONE FOR ALL®
brand for North America.
Copyright 2006 by Universal Electronics nc.No part of this publication
may be reproduced,transmitted,transcribed,stored in any retrieval sys-
tem, or translated to any language, in any form or by any means, elec-
tronic, mechanical, magnetic, optical, manual, or otherwise, without the
prior written permission of Universal Electronics nc.
One For All® 3 Devices is compatibile for use in North America excluding
Mexico.
URC-3110 07/08
11

12
MA UFACTURER’S CODES
Setup Codes for Cable Boxes
ABC 0003, 0008
Americast 0899
Bell South 0899
Digeo 1187
General nstrument 0003, 0276
Jerrold 0003, 0276
Memorex 0000
Motorola 0276, 1187, 1376
Pace 0008, 1877
Panasonic 0000
Paragon 0000
Pioneer 0533, 1877
Pulsar 0000
Quasar 0000
Runco 0000
Scientific Atlanta 0008, 1877
Starcom 0003
Supercable 0276
Torx 0003
Toshiba 0000
Zenith 0000, 0899
Setup Codes for Cable Box/PVR (or DVR) Combos
Setup Codes for Satellite Receivers
DirecTV 1377, 0099, 0247, 0392, 0566,
0639, 0724, 0749, 0819, 1076,
1108, 1142,1392, 1442, 1609,
1639, 1640, 1749, 1856
Dish Network 0775
Dish Network System 0775, 1005, 1505, 1775
Dishpro 0775, 1005, 1505, 1775
Echostar 0775, 1005, 1505, 1775
Expressvu 0775, 1775
GE 0392, 0566
General nstrument 0869
GO 0775, 1775
Hisense 1535
Hitachi 0819
HTS 0775, 1775
Hughes 0749, 1442, 1749
Hughes Network
Systems 0749, 1142, 1442, 1749
iLo 1535
Jerrold 0869
JVC 0775, 1775
Magnavox 0724
Memorex 0724
Mitsubishi 0749
Motorola 0856, 0869
Next Level 0869
Panasonic 0247, 0701
Paysat 0724
Philips 0099, 0724, 0749, 0819, 1076,
1142, 1442, 1749
Pioneer 442
Proscan 0392, 0566
Proton 1535
RadioShack 0869
RCA 0392, 0566, 0855, 1392
Samsung 1108, 1142, 1276, 1377, 1442,
1609
Sony 0639, 1639, 1640
Star Choice 0869
Tivo 1142, 1442
Toshiba 0749, 0790, 0819, 1285, 1749
UltimateTV 1392, 1640
Uniden 0724
US Digital 1535
USDTV 1535
Voom 0869
Zenith 1856
Americast 0899
Digeo 1187
Motorola 1376, 1187
Pace 1877
Pioneer 1877
Scientific Atlanta 1877
Zenith 0899
DirecTV 1377, 0099, 0392, 0639,
1076, 1142, 1392, 1442,1640
Dish Network System 0775, 1505
Dishpro 0775, 1505
Echostar 0775, 1505
Expressvu 0775
Hughes Network
Systems 1142, 1442
Motorola 0869
Philips 1142, 1442
Proscan 0392
RCA 1392
Samsung 1442
Sony 0639, 1640
Star Choice 0869
continued on next page...
Setup Codes for Satellite Receiver/PVR (or DVR) Combos

13
MA UFACTURER’S CODES
Setup Codes for TVs
Admiral 0093, 0463
Advent 0761, 0783, 0815, 0817, 0842
Aiko 0092
Akai 0030, 0060, 0672, 0702, 0812
America Action 0180
Anam 0180
AOC 0030
Apex Digital 0156, 0748, 0765, 0767, 0879
Audiovox 0092, 0180, 0451
Aventura 0171
Bell & Howell 0154
Bradford 0180
Broksonic 0180, 0236, 0463
Candle 0030
Carnivale 0030
Carver 0054
Celebrity 0000
Celera 0765
Changhong 0765
Citizen 0030, 0060, 0092
Clarion 0180
CommercialSolutions 0047
Contec 0180
Craig 0180
Crosley 0054
Crown 0180
Curtis Mathes 0030, 0047, 0054, 0060, 0093,
0145, 0154, 0166, 0451, 0702
CXC 0180
Daewoo 0092, 0451, 0672, 1661
Denon 0145
Diamond Vision 1996, 1997
Dumont 0017
Durabrand 0171, 0178, 0180, 0463, 1034
Dwin 0093
Electroband 0000
Electrograph 1755
Emerson 0154, 0171, 0178, 0180, 0236,
0451, 0463, 1944, 1963
Envision 0030
ESA 0171, 0812
Fisher 0154
Funai 0171, 0180
Futuretech 0180
Gateway 1755, 1756
GE 0047, 0051, 0178, 0451
Gibralter 0017, 0030
GoldStar 0030, 0178
Grunpy 0180
Haier 1034
Hallmark 0178
Harman/Kardon 0054
Harvard 0180
Havermy 0093
Hello Kitty 0451
Hisense 0748
Hitachi 0145
iLo 1286
nfinity 0054
nsignia 1204
nteq 0017
JBL 0054
JCB 0000
Jensen 0761, 0815, 0817
JVC 0053
KEC 0180
Kenwood 0030
KLH 0765, 0767
KTV 0030, 0180
LG 0178, 1265
LX 0047, 0054, 0154, 0156, 0178
Magnavox 0030, 0054, 1944, 1963
Marantz 0030, 0054
Matsushita 0250
Maxent 1755
Megatron 0145, 0178
Memorex 0150, 0154, 0178, 0463
MGA 0030, 0150, 0178
Midland 0017, 0047, 0051
Mitsubishi 0093, 0150, 0178, 1250
Motorola 0093
MTC 0030, 0060
Multitech 0180
NAD 0156, 0178
NEC 0030
NetTV 1755
Nikko 0030, 0092, 0178
Norcent 0748
Norwood Micro 1286
NTC 0092
Onwa 0180
Optimus 0154, 0166, 0250
Optonica 0093, 0165
Orion 0236, 0463
Panasonic 0051, 0250
Penney 0030, 0047, 0051, 0060, 0156,
0178
Philco 0030, 0054
Philips 0054, 0690
Pilot 0030
Pioneer 0166, 0679
Polaroid 0765
Portland 0092
Prima 0761, 0783, 0815, 0817
Prism 0051
Proscan 0047
Proton 0178
Pulsar 0017
Quasar 0051, 0165, 0250
RadioShack 0030, 0047, 0154, 0165, 0178,
0180
RCA 0047, 0090, 0679
Realistic 0030, 0154, 0165, 0178, 0180
Runco 0017, 0030
Sampo 0030, 1755
Samsung 0030, 0060, 0178, 0702, 0812
Sansui 0463
Sanyo 0154

14
Scotch 0178
Scott 0178, 0180, 0236
Sears 0047, 0054, 0154, 0156, 0171,
0178
Sharp 0093, 0165
Sheng Chia 0093
Sony 0000
Soundesign 0178, 0180
Squareview 0171
SSS 0180
Starlite 0180
Superscan 0093
Supreme 0000
SVA 0748
Sylvania 0030, 0054, 0171, 1944, 1963
Symphonic 0171, 0180
Tandy 0093
Tatung 1286, 1756
Technics 0051, 0250
Techwood 0051
Teknika 0054, 0060, 0092, 0150, 0180
Telefunken 0702
TMK 0178
TNCi 0017
Toshiba 0060, 0154, 0156, 1265
TVS 0463
US Logic 1286
Vector Research 0030
Victor 0053
Vidikron 0054
Vidtech 0178
Viewsonic 1755
Vizio 1756
Wards 0030, 0054, 0165, 0178
Waycon 0156
Westinghouse 0000, 0451
White Westinghouse 0463
Yamaha 0030
Zenith 0017, 0092, 0178, 0463, 1265
ABS 1972
Admiral 0048, 0209
Adventura 0000
Aiwa 0000, 0037
Alienware 1972
American High 0035
Asha 0240
Audiovox 0037
Beaumark 0240
Bell & Howell 0104
Broksonic 0121, 0184, 0209, 1479
Calix 0037
Canon 0035
Carver 0081
CCE 0072
Citizen 0037, 1278
Colt 0072
Craig 0037, 0047, 0072, 0240
Curtis Mathes 0035, 0060, 0162, 1035
Cybernex 0240
CyberPower 1972
Daewoo 0045, 1278
Dell 1972
Denon 0042
DirecTV 0739
Durabrand 0039
Dynatech 0000
Electrohome 0037, 0043
Electrophonic 0037
Emerex 0032
Emerson 0000, 0037, 0043, 0121, 0184,
0209, 0593, 1278, 1479, 1593
Fisher 0047, 0104
Fuji 0035
Funai 0000, 0593, 1593
Garrard 0000
Gateway 1972
GE 0035, 0060, 0240, 0807, 1035,
1060
Go Video 0240
GoldStar 0037, 1237
Gradiente 0000
Harley Davidson 0000
Harman/Kardon 0081
Harwood 0072
Hewlett Packard 1972
H -Q 0047
Hitachi 0000, 0042
Howard Computers 1972
HP 1972
Hughes Network
Systems 0042, 0739
Humax 0739
Hush 1972
iBUYPOWER 1972
JVC 0067
KEC 0037
Kenwood 0067
KLH 0072
Kodak 0035, 0037
Linksys 1972
Lloyd's 0000
Logik 0072
LX 0037
Magnasonic 0593, 1278
Magnavox 0000, 0035, 0039, 0081, 0593
Magnin 0240
Marantz 0035, 0081
Marta 0037
Matsushita 0035, 0162
Media Center PC 1972
ME 0035
Memorex 0000, 0035, 0037, 0039, 0047,
0048, 0104, 0162, 0209, 0240,
1237
MGA 0043, 0240
MGN Technology 0240
Microsoft 1972
Mind 1972
continued on next page...
Setup Codes For VCRs

15
Setup Codes for PVRs (or DVRs)
Minolta 0042
Mitsubishi 0043, 0067, 0807
Motorola 0035, 0048
MTC 0000, 0240
Multitech 0000, 0072
NEC 0067, 0104
Nikko 0037
Niveus Media 1972
Noblex 0240
Northgate 1972
Olympus 0035
Optimus 0037, 0048, 0104, 0162, 0593,
1062
Orion 0184, 0209, 1479
Panasonic 0035, 0162, 0616, 1035, 1062
Penney 0035, 0037, 0042, 0240, 1035,
1237
Pentax 0042
Philco 0035
Philips 0035, 0081, 0618, 0739
Pilot 0037
Pioneer 0067
Polk Audio 0081
Presidian 1593
Profitronic 0240
Proscan 0060, 1060
Protec 0072
Pulsar 0039
Quasar 0035, 0162, 1035
RadioShack 0000
Radix 0037
Randex 0037
RCA 0042, 0060, 0240, 0807, 0880,
1035, 1060
Realistic 0000, 0035, 0037, 0047, 0048,
0104
ReplayTV 0614, 0616
Ricavision 1972
Runco 0039
Samsung 0045, 0240, 0739, 1014
Sanky 0039, 0048
Sansui 0000, 0067, 0209, 1479
Sanyo 0047, 0104, 0240
Scott 0043, 0045, 0121, 0184
Sears 0000, 0035, 0037, 0042, 0047,
0104, 1237
Sharp 0048, 0807
Shintom 0072
Shogun 0240
Singer 0072
Sonic Blue 0614, 0616
Sony 0000, 0032, 0035, 0636, 1232,
1972
Stack 9 1972
STS 0042
Sylvania 0000, 0035, 0043, 0081, 0593,
1593
Symphonic 0000, 0593, 1593
Systemax 1972
Tagar Systems 1972
Teac 0000
Technics 0035, 0162
Teknika 0000, 0035, 0037
Thomas 0000
Tivo 0618, 0636, 0739
TMK 0240
Toshiba 0043, 0045, 0209, 0845, 1008,
1145, 1972, 1503
Totevision 0037, 0240
Touch 1972
Unitech 0240
Vector 0045
Video Concepts 0045
Videomagic 0037
Videosonic 0240
Viewsonic 1972
Villain 0000
Voodoo 1972
Wards 0000, 0035, 0042, 0047, 0048,
0060, 0072, 0081, 0240
White Westinghouse 0072, 0209
XR-1000 0000, 0035, 0072
Zenith 0000, 0039, 0209, 1479
ZT Group 1972
MA UFACTURER’S CODES
Setup Codes for VCRs (continues)
ABS 1972
Alienware 1972
CyberPower 1972
Dell 1972
DirecTV 0739
Gateway 1972
Hewlett Packard 1972
Howard Computers 1972
HP 1972
Hughes Network
Systems 0739
Humax 0739
Hush 1972
iBUYPOWER 1972
Linksys 1972
Media Center PC 1972
Microsoft 1972
Mind 1972
Niveus Media 1972
Northgate 1972
Panasonic 0616
Philips 0618, 0739
RCA 0880
ReplayTV 0614, 0616
Samsung 0739
Sonic Blue 0614, 0616
Sony 0636, 1972
Stack 9 1972
Systemax 1972
Tagar Systems 1972
Tivo 0618, 0636, 0739

16
Toshiba 1008, 1972
Touch 1972
Viewsonic 1972
Voodoo 1972
ZT Group 1972
Setup Codes For TV/VCR Combos
Broksonic 1479
Citizen 1278
Colt 0072
Curtis Mathes 1035
Daewoo 1278
Emerson 0593, 1278, 1479
Funai 0000
GE 0240, 0807, 1035, 1060
GoldStar 1237
Harley Davidson 0000
Hitachi 0000
Lloyd's 0000
Magnasonic 0593, 1278
Magnavox 0000, 0593
Magnin 0240
Memorex 0162, 1237
MGA 0240
Mitsubishi 0807
Optimus 0162, 0593
Orion 1479
Panasonic 0162, 1035
Penney 0240, 1035, 1237
Quasar 0162, 1035
RadioShack 0000
RCA 0240, 0807, 1035, 1060
Samsung 1014
Sansui 0000, 1479
Sanyo 0240
Sears 0000, 1237
Sony 0000, 1232
Symphonic 0000, 0593
Thomas 0000
Toshiba 0845, 1145
Zenith 0000, 1479
Setup Codes for DVD Players
Akai 0695, 0899
Alco 0790
Apex Digital 0672, 0717, 0755, 0794, 0796,
0830, 1020, 1056, 1061
Aspire Digital 1168
Audiovox 0790
Blaupunkt 0717
Blue Parade 0571
Broksonic 0695
CaliforniaAudioLabs 0490
Citizen 1277
CyberHome 1129
Daewoo 1169, 1172
Denon 0490
Diamond Vision 1316, 1609, 1610
Disney 0675, 1270
Durabrand 1127
DVD2000 0521
Emerson 0675, 0821, 1268
Funai 0675, 1268, 1334
Gateway 1073, 1158
GE 0522, 0717
Go Video 0741, 0744, 1044, 1075, 1158,
1304, 1730
GoldStar 0741
Gradiente 0490
Greenhill 0717
Grundig 0539
Hitachi 0573, 1247
Hiteker 0672
iLo 1348, 1472
nitial 0717, 1472
nsignia 1830
ntegra 0571, 0627
JVC 0558, 0623, 0867, 1164
Kawasaki 0790
Kenwood 0490
KLH 0717, 0790, 1020, 1149
Lecson 1533
Lenoxx 1127, 1938
LG 0741
LiteOn 1158, 1416, 1440
Magnavox 0503, 0539, 0646, 0675, 0821,
1268
Marantz 0539
Mc ntosh 1533
Memorex 0695, 1270
Microsoft 0522
Mintek 0717, 1472
Mitsubishi 0521, 1521
NAD 0741
Nesa 0717
NexxTech 1402, 1830
Norcent 1830
Onkyo 0503, 0627
Panasonic 0490, 0503, 0703, 1362, 1462,
1490, 1762
Philips 0503, 0539, 0646, 0675, 1260,
1267, 1354
Pioneer 0525, 0571
Polaroid 1020, 1061, 1316
Polk Audio 0539
Presidian 0675
Proceed 0672
Proscan 0522
RCA 0522, 0571, 0717, 0790, 0822,
1022, 1132
Regent 1938
Rotel 0623
Samsung 0490, 0573, 0744, 0820, 0899,
1044, 1075
Sansui 0695
Sanyo 0695
Sensory Science 1158
Sharp 0630, 0675, 1256
continued on next page...

17
Setup Codes For DVD Player/VCR Combos
Setup Codes For TV/DVD Player Combos
Apex Digital 1061
Broksonic 0695
Emerson 0675
Funai 0675
Go Video 0741, 0744, 1044, 1075
GoldStar 0741
JVC 0867, 1164
LG 0741
Memorex 0695
Panasonic 1762
Philips 0675, 1267
Polaroid 1061
Presidian 0675
RCA 0522, 0822
Samsung 0820, 1044, 1075
Sansui 0695
Sharp 0630
Sony 0864, 1033, 1431
Sylvania 0675
Symphonic 0675
Toshiba 0503
Zenith 0741
Akai 0695
Apex Digital 0830
Broksonic 0695
Diamond Vision 1610
Emerson 0675, 1268
Hitachi 1247
iLo 1472
nitial 1472
Magnavox 1268
Mintek 1472
Panasonic 1490
Philips 1260
RCA 1022
Samsung 0899
Sansui 0695
Sylvania 0675, 1268
Toshiba 0695
Setup Codes For TV/VCR/DVD Player Combos
Akai 0899
Diamond Vision 1609
Emerson 0821
Funai 1334
Magnavox 0821
Panasonic 1362, 1462
RCA 1132
Sharp 0630
Superscan 0821
Sylvania 0821
Toshiba 1045
MA UFACTURER’S CODES
Setup Codes for DVD Players (continues)
Shinsonic 0533
Sony 0533, 0864, 1033, 1431, 1533
Superscan 0821
Sylvania 0675, 0821, 1268
Symphonic 0675, 1268
Teac 0790
Technics 0490, 0703
Theta Digital 0571
Toshiba 0503, 0695, 1045, 1154
Urban Concepts 0503
Venturer 0790
Xbox 0522
Yamaha 0490, 0539
Zenith 0503, 0741