One Lux OS/5.8/C User manual

OS/5.8/C User Guide
www.one-lux.com
Document Number: 19932/B
Page 1
Properties
Detects movement and presence through glass and plastic diffusers.
Light sensor configurable within the Casambi App.
User-configurable DIP Switch settings for Sensitivity.
Casambi controlled built-in relay for local switched live out.
Ultra-low microwave power, around 1/10th of that emitted by mobile phones.
For mounting heights of 2m to 6m in internal applications*.
Compatible for multi-sensor operation of a single luminaire.
Push-wire terminals for solid conductors up to 1.5mm2.
Common neutral provided for easy input/output wiring.
Complies with ETSI EN300 440, EN60669-1 & EN60669 Part 2_1.
* Microwave sensors may not be suitable for certain outdoor applications
Product description
OS/5.8/C is a UK designed and built microwave presence detector with built-in Casambi wireless node capable of remote intelligent ON/OFF
switching control via the Casambi ecosystem.
Their Radar Doppler technology operates at 5.8Ghz and achieves a detection range of 6m in typical office environments.
Presence detection status and light sensor output can be configured from within the Casambi App to control other Casambi-enabled equipment
without need for complex wiring.
The compact, low-profile enclosure is ideal for fixing within a luminaire, so provides simple, reliable cost-effective means of instantly reducing
lighting energy bills.
Technical Specifications
Input Supply Voltage 230Vac +/- 10% 50Hz
Standby/ Operating Power 1.2W/ 1.7W
Maximum switching current 0.5A
Detection Area (Typical) 4 - 6m Radius at 2.5m Ceiling Height)
Operating Temperature 0° to 50°C
Detector Operating Frequency 5.8GHz
Casambi Operating Frequency 2.4GHz
Sensitivity Settings 100, 75, 50, 25, 10%
On-time Settings Casambi App Configured
Light sensor range 0-1000lux - Casambi App Configured
IP Rating IP20
Weight 50g
Rated Load 400W (inductive load), 800W (resistive load)
Detection Area 4-6m radius at 2.5m ceiling height (typical)
On time 5sec, 30sec, 180sec, 300sec, 15min, 25min
Daylight Sensor 2lux, 5lux, 20lux, 30lux, Disable
Sensor Principle Microwave motion detector
Microwave Frequency 5.8GHz Continuous Wave
Transmitting Power <0.5mW (1% of transmitting power of cell phone)
Parasitic Load <1.7W (daylight/motion sensing only)
Operating Temperature 0-50C
IP Rating IP20

Page 2
Movement Sensor
The OS/5.8/C is designed for installation at a height of 1-6m with a
suggested mounting height of 1-1.8m (wall mounting) and 2.5-6m
(ceiling mounting). The sensitivity of detection can be reduced from
100% down to 10% with the user selectable DIP switches. Typical
detection patterns are illustrated above, but please note many factors
can affect the level of detection, such as speed of walking, amount of
arm movement etc. Microwaves cannot pass through metal or brick
walls thicker than 20cm. They will pass through thinner walls but
there will be some attenuation.
Installation inside a glass or plastic housing will result in a reduction
of sensitivity. Expect a reduction of approximately 20% for every 3mm
of thickness.
Light Sensor
An internal light sensor is located near the supply terminal block and can
transmit information to the Casambi App where the level can be calibrated
for use in the lighting scheme as required.
The sensor should be positioned so facing the ambient light to be
measured and to avoid detecting light from the luminaire’s own light
source.
Status Indicator
An LED status indicator illuminates red for power on/ detecting and green
when movement is detected.
Typical Microwave Detection Pattern and Settings
Installation & Wiring
Fix the sensor to a solid surface within the luminaire (or suitable
protective enclosure) and with the microwave antenna (Printed
surface of the lid) pointing towards the area requiring presence
detection. The sensor should be wired according the diagrams
below. Please visit www.casambi.com for latest information and
configuration details within the Casambi app.