Onix OIA82 User manual

OIA82
OWNER MANUAL'S
INTEGRATED AMPLIFIER
VOLUME
INPUT
ON / STANDBYON /STANDBY
INTEGRATED AMPLIFIER 2OIA8INTEGRATED AMPLIFIER OIA82

We thank you for purchasing this ONIX Integrated Amplifier. Please read all the safety and operating instructions before
using the product. Retain the manual for future reference and adhere to all warnings in the manual or on the amplifier.
Notices for Use
CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN.
The lightning flash with an arrowhead symbol within an equilateral triangle is intended
to alert the user to the presence of un-insulated dangerous voltage within the product s
enclosure which may be of sufficient magnitude to constitute a risk of electric shock.
'
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the
literature accompanying the product.
Fig.1 Fig.2
1. Do not open this device yourself to repair or modify it.
Opening this device or
attempting to carry out any modification without approval may affect the performance or quality of this device.
2. For good ventilation, a minimum of 10cm clearance shall be maintained at the back and two sides and 20cm at the top of
the unit.
Allow no water dripping or splashing into the unit. Place no object containing liquid on the unit, e.g. Vase.
4. Do not cover any ventilation hole with newspaper, cloth, curtain, etc. in case of ventilation blocking.
5. Allow no exposed flame source on the unit, e.g. burning candle.
The unit shall be connected toAC power output socket with grounding protection.
If power plug and appliance coupler are used as disconnecting device, the disconnecting device shall be easily operable.
8. Any batteries requiring disposal must be handled in accordance with local regulations.
9. This device is intended for safe use in an area with elevation under 2000m. (Fig.1)
10. This device is intended for safe use under non-tropical climate conditions. (Fig.2)
You should never attempt to service the product beyond that
described in this manual. All other servicing should be referred to qualified service personnel.
3.
6.
7.

ON / STANDBYON /STANDBY
VOLUME
INPUT
INTEGRATED AMPLIFIER 2OIA8INTEGRATED AMPLIFIER OIA82
R
PHONO
L
CD DVD AUX BYPASS PRE
XLR RCA
R
L
UPDATE
STEREO
MONO
MONO AMP
MONO AMP XLR
MONO AMP RCA
HIGH GAINHIGH GAIN
LOW GAINLOW GAIN
XLR
IN OUT1
IR
OUT2
MONO INMONO IN
MONO AMP IN
POWER
AC INAC IN
ONOFF
FUSE
100V - 120V: T10AL100V -120V: T10AL
220V - 240V: T8AL220V-240V: T8AL
MODEL: OIA82MODEL: OIA82
POWER CONSUMPTION: 600WPOWER CONSUMPTION: 600W
INTEGRATED AMPLIFIER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
USE ONLYWITH A 250V FUSEUSE ONLYWITH A 250V FUSE
SPEAKER RIGHTSPEAKER RIGHT SPEAKER LEFTSPEAKER LEFT
A
B
A
B
~/220V 50Hz~/220V 50Hz
IN-STEREO-OUTIN -STEREO -OUT
ONIX ENGLAND ELECTRONICS LTD
SERIAL NO.:
Names of Parts
1. Signal selection button
2. Display window
3. Standby contact switch (the whole metal bar)
4. Standby indicator light
5. Remote control receiving window
6. Volume adjusting knob
1. PRE AMP signal output interface
2. BYPASS pass signal input interface
3. AUX signal input interface
4. DVD signal input interface
5. CD signal input interface
6. PHONO player signal input interface
7. XLR signal input interface
8. Right sound channel s output interface
9. Mode selection switch (built in STEREO)
peaker
10. Adding selection switch
11. Ground terminal
12. AC input socket (fuse attached)
13. Software upgrading interface
14. Remote control signal input interface
15. Main power switch
16. Remote control signal output interface 1
17. Remote control signal output interface 2
18. Right sound channel s output interfacepeaker
I. Stereo Mode

R
PHONO
L
CD DVD AUX BYPASS PRE
XLR RCA
R
L
UPDATE
STEREO
MONO
MONO AMP
MONO AMP XLR
MONO AMP RCA
HIGH GAINHIGH GAIN
LOW GAINLOW GAIN
XLR
IN OUT1
IR
OUT2
MONO INMONO IN
MONO AMP IN
POWER
AC INAC IN
ONOFF
FUSE
100V - 120V: T10AL100V -120V: T10AL
220V - 240V: T8AL220V-240V: T8AL
MODEL: OIA82MODEL: OIA82
POWER CONSUMPTION: 600WPOWER CONSUMPTION: 600W
INTEGRATED AMPLIFIER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
USE ONLYWITH A 250V FUSEUSE ONLYWITH A 250V FUSE
SPEAKER RIGHTSPEAKER RIGHT SPEAKER LEFTSPEAKER LEFT
A
B
A
B
~/220V 50Hz~/220V 50Hz
IN-STEREO-OUTIN -STEREO -OUT
ONIX ENGLAND ELECTRONICS LTD
SERIAL NO.:
RR
PHONOPHONO
LL
CDCD DVDDVD AUXAUX BYPASSBYPASS PREPRE
XLRXLR RCARCA
RR
LL
UPDATE
STEREO
MONO
MONO AMP
MONO AMP XLR
MONO AMP RCA
HIGH GAINHIGH GAIN
LOW GAINLOW GAIN
XLR
IN OUT1
IR
OUT2
MONO INMONO IN
MONO AMP IN
POWER
AC INAC IN
ONOFF
FUSE
100V - 120V: T10AL100V -120V: T10AL
220V - 240V: T8AL220V-240V: T8AL
MODEL: OIA82MODEL: OIA82
POWER CONSUMPTION: 600WPOWER CONSUMPTION: 600W
INTEGRATED AMPLIFIER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
USE ONLYWITH A 250V FUSEUSE ONLYWITH A 250V FUSE
SPEAKER RIGHTSPEAKER RIGHT SPEAKER LEFTSPEAKER LEFT
A
B
A
B
~/220V 50Hz~/220V 50Hz
IN-STEREO-OUTIN -STEREO -OUT
ONIX ENGLAND ELECTRONICS LTD
SERIAL NO.:
II. Mono Bridged Mode
1. AUX signal input interface
2. DVD signal input interface
3. CD signal input interface
4. PHONO player signal input interface
5. XLR signal input interface
6. Speaker output interface "-" end
7. Mode selection switch (built in Mono)
8. Adding selection switch
9. Ground terminal
10. AC input socket (fuse attached)
11. Software upgrading interface
12. Remote control signal input interface
13. Main power switch
14. Remote control signal output interface 1
15. Remote control signal output interface 2
16. Speaker output interface "+" end
III. Mono Sound Channel Back End Mode
1. RCA signal input interface
2. XLR signal input interface
3. output interface "-" end
4. Mode selection switch (built in MONO AMP)
5. Input source selection switch
6. AC input socket (fuse attached)
Speaker
7. Software upgrading interface
8. Remote control signal input interface
9. Main power switch
10. Remote control signal output interface 1
11. Remote control signal output interface 2
12. output interface "+" endSpeaker

Install Battery
1. Open the battery cover.
3. Close the battery cover.
Mute button
Input shift selection button
Volume up button
Volume down button
2. Insert 2 AAA batteries and check the positive and negative polarity of the
batteries is correct.
Remote Control Diagram
Brightness adjusting button
Standby switch button
(press and hold)
Device mode shift button
(placing at CD/AMP position)
Notes:
The unmarked button are not functional buttons
of the device, therefore pressing those button is
invalid operation.

Operation Instructions
Preparations
3. When the device needs to be powered off, touch the metal bar on the panel (more than 1 second) or press and hold on the
CD/AMP button, the indication light will turn red. At this time, the device is in a standby mode. Move the power
switch on the back panel to off position and the device is powered off.
1. Properly connect the power line, signal line of the device and the amplifier, and make sure the connection of the output line
of the amplifier has no short circuit. Rotate the volume adjusting knob counterclockwise to the minimal position.
2. Move the power switch on the back-panel to ON position. The indication light of the ON/STANDBY on the panel
will turn red. At this time, touch the metal bar (more than 1 second) or press and hold the CD/AMP button on the
remote control, the indication light will turn to green, and the device will start to work. After about 3 seconds, the relay
closes, then you can select corresponding input interface, and adjust the volume by rotating the knob slowly to a proper
position, then the device will start to work.
4. If the device will not be used for a long time, please unplug the AC power line connected to the device.
Input shift
Rotate the INPUT knob on the board or press the button on the remote control, the audio source can be
shifted to the corresponding input interface, and the current input will be displayed on the display screen.
INPUT
Volume adjusting
Adjusted volume by rotating VOLUME knob on the front-panel, while rotating counterclockwise is reducing the
volume, rotating clockwise is increasing the volume. The volume can also be adjusted by pressing the
button on the remote control.
VOLUME + -
Notes: Before starting the device, please make sure the volume knob is not rotated to an excessive position, otherwise the
sound box will be burnt.
Mute
1. When the audio function is normally working, press the MUTE button on the remote control, there will be a
MUTE on the display screen, then the audio output of the device is stopped.
2. When the device is in a mute condition, press the MUTE button once, the audio function is restarted.
Output protection
When the device is overloaded, the relay that protects the device will disconnect at once, and there will be a PROTECT
displayed on the display screen. At this time, you should power off the device and check and remove the overloading. 5
minutes later, restart the device, and the device will start to work in normal state.
Gain adjusting
This function enables users to choose different devices (amplifier or signal source). When the sensitivity of the amplifier is
low or the signal source output electric level is low, please move the gain selection switch to a HIGH GAIN position;
when the amplifier is highly sensitive or the signal source output electric level is high, please move the gain selection switch
to a LOW GAIN position.
Mode selection
Users can select different mode according to their requirement.

Display brightness adjusting
1. Combining the brightness of play environment, press the DIMMER button on the remote control to adjust the
brightness of the displayed words.
2. Press DIMMER button on the remote control, the display brightness intensity circulate among bright, dim, off ,
and each time the users press, the brightness will be changed to the next mode.
3. When the device is started, the display screen is automatically put into a bright status.
Note: If the amplifier still exhibits a fault after checking the possible causes, please contact your local distributor or service
centre. Return the machine to service centre if necessary.
Troubleshooting
Fault
No power
No sound
No remote control
Possible causes
Poor connection in socket or no utility.
Audio cable not connected.
Volume knob is at min.
Remote battery misplaced or depleted.
Solution
Check power source and connect socket tightly.
Re-connect audio cables.
Adjust volume to preferred level
Reinstall or replace batteries.

Accessories
User manual
Power source line
Remote control
Input sensitivity rate 300mV (RCA); 600mV (XLR) (H GAIN)
600mV (RCA); 1.2V (XLR) (L GAIN)
Frequency response: 10Hz-30KHz (-1dB)
Player input sensitivity rate (MM) 2mV (H GAIN)
4mV (L GAIN)
THD <0.009% (5W)
Maximum output power 360W/4 Ohm 2; 200W/8 Ohm 2 (Stereo)
SNR >98dB
Power consumption 600W
Dimension (W D H) 480 468 210mm
Net weight About 28kg
Technical Specification
500W/8 Ohm (Mono)

ON / STANDBYON /STANDBY
VOLUME
INPUT
INTEGRATED AMPLIFIER 2OIA8INTEGRATED AMPLIFIER OIA82
R
PHONO
L
CD DVD AUX BYPASS PRE
XLR RCA
R
L
UPDATE
STEREO
MONO
MONO AMP
MONO AMP XLR
MONO AMP RCA
HIGH GAINHIGH GAIN
LOW GAINLOW GAIN
XLR
IN OUT1
IR
OUT2
MONO INMONO IN
MONO AMP IN
POWER
AC INAC IN
ONOFF
FUSE
100V - 120V: T10AL100V -120V: T10AL
220V - 240V: T8AL220V-240V: T8AL
MODEL: OIA82MODEL: OIA82
POWER CONSUMPTION: 600WPOWER CONSUMPTION: 600W
INTEGRATED AMPLIFIER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
USE ONLYWITH A 250V FUSEUSE ONLYWITH A 250V FUSE
SPEAKER RIGHTSPEAKER RIGHT SPEAKER LEFTSPEAKER LEFT
A
B
A
B
~/220V 50Hz~/220V 50Hz
IN-STEREO-OUTIN -STEREO -OUT
ONIX ENGLAND ELECTRONICS LTD
SERIAL NO.:

R
PHONO
L
CD DVD AUX BYPASS PRE
XLR RCA
R
L
UPDATE
STEREO
MONO
MONO AMP
MONO AMP XLR
MONO AMP RCA
HIGH GAINHIGH GAIN
LOW GAINLOW GAIN
XLR
IN OUT1
IR
OUT2
MONO INMONO IN
MONO AMP IN
POWER
AC INAC IN
ONOFF
FUSE
100V - 120V: T10AL100V -120V: T10AL
220V - 240V: T8AL220V-240V: T8AL
MODEL: OIA82MODEL: OIA82
POWER CONSUMPTION: 600WPOWER CONSUMPTION: 600W
INTEGRATED AMPLIFIER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
USE ONLYWITH A 250V FUSEUSE ONLYWITH A 250V FUSE
SPEAKER RIGHTSPEAKER RIGHT SPEAKER LEFTSPEAKER LEFT
A
B
A
B
~/220V 50Hz~/220V 50Hz
IN-STEREO-OUTIN -STEREO -OUT
ONIX ENGLAND ELECTRONICS LTD
SERIAL NO.:
RR
PHONOPHONO
LL
CDCD DVDDVD AUXAUX BYPASSBYPASS PREPRE
XLRXLR RCARCA
RR
LL
UPDATE
STEREO
MONO
MONO AMP
MONO AMP XLR
MONO AMP RCA
HIGH GAINHIGH GAIN
LOW GAINLOW GAIN
XLR
IN OUT1
IR
OUT2
MONO INMONO IN
MONO AMP IN
POWER
AC INAC IN
ONOFF
FUSE
100V - 120V: T10AL100V -120V: T10AL
220V - 240V: T8AL220V-240V: T8AL
MODEL: OIA82MODEL: OIA82
POWER CONSUMPTION: 600WPOWER CONSUMPTION: 600W
INTEGRATED AMPLIFIER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
MONO
SPEAKER
USE ONLYWITH A 250V FUSEUSE ONLYWITH A 250V FUSE
SPEAKER RIGHTSPEAKER RIGHT SPEAKER LEFTSPEAKER LEFT
A
B
A
B
~/220V 50Hz~/220V 50Hz
IN-STEREO-OUTIN -STEREO -OUT
ONIX ENGLAND ELECTRONICS LTD
SERIAL NO.:

Due to continuous improvement, every specification and design is
subject to change at any time without further notice.
www.onix-audio.co.uk
ONIX ELECTRONICS LTDENGLAND