Openpath 2ESH User manual

Single Door Controller
Quick Start Guide
Openpath Technical Support
[email protected]
1-844-673-6728 ext 2
The 5150-5350MHz band is allocated for indoor use only in EU
member countries.
Single Door Controller
Power rating:
DC Input: 24/12VDC 1.1A/2.2A
PoE Input: 48VDC 0.55A
⎓
⎓
Install guides:
FCC COMPLIANCE INFORMATION
PRODUCT: Single Door Controller
Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his own expense.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 centimeters between the radiator and your body.
RESPONSIBLE PARTY:
Openpath Security, Inc. 13428 Maxella Ave, #866 Marina Del Rey, CA 90292 • 1-844-673-6728 • www.openpath.com
Industry Canada Notice and Marking
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
Ce produit répond aux spécifications techniques applicables à l'innovation, Science et Développement économique Canada.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
“Operations in the 5.15-5.25Ghz band are restricted to indoor usage only.”
Le fonctionnement sur la bande 5,15–5,25Ghz est limité à une utilisation intérieure uniquement.
This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and
operated with minimum distance 20cm between the radiator & your body.
Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps.

G
A
B
B
E
D
D
F
C
C
G
A
B
E
D
F
C
C
Admin app:
WARNING: Remove DC Input
Power and PoE before changing
the voltage of the relays.
Voltage Switches
To power relays without
external supply, select 12V or
24V, and connect locking
hardware to NO/NC and GND
( ). To use external power,
select DRY and use NO/NC
and C, and wire to external
supply.
24V
Provision
1. Open the Admin app
2. Search for org name
3. Press Admin button on SDC
4. Tap Provision in Admin
app and follow instructions
OP Readers
Sensors
Locks
Solid
Blinking
Normal operation
Error state
Solid
Blinking
Solid
Blinking
Active
EOL shorted or cut
Relay is energized
Fault detection
PORT LEDS
Solid White
Blinking Red
Solid Cyan
Solid Yellow
Blinking Yellow
Solid Blue
Solid Purple
Blinking Purple
Solid Red
Normal operation
No Internet
Booting
Restoring software
Updating software
Unprovisioned state
Connected to app
Ready to connect to app
Error, see Control Center
STATUS LED
To set up this device, download the Openpath Admin app at openpath.com/su/adminapp
Output Ratings
• Power Out can supply up to
100mA @ 12V or 50mA @ 24V
• 2 reader ports, max power
output: 250mA @ 12V each
• 2 relays, max power output:
PoE: Max 3W combined output
(250mA @ 12V, 125mA @ 24V)
PoE+: Max 9W combined output
(750mA @ 12V, 375mA @ 24V)
REX
NO
C
NC
STATUS LED
ADMIN BUTTON
SIDE VIEW
power out
relay 1
reader 1
reader 2
wiegand 1
rex 1
contact 1
rex 2
contact 2
relay 2
wiegand 2
power in
24V
12V
NO
C
NC
NO
C
NC
R1
C1
12V
A-
B+
D1
D0
R2
C2
12V
A-
B+
D1
D0
VDC
12V (WET)
24V (WET)
DRY
SD CARD
ETHERNET
ENTRY 1
ENTRY 2
Orange
Violet
Blue
Gray READER
USB USB
EXTERNAL
24V
POWER
SUPPLY
–
+
24V FAIL
SAFE MAG
LOCK
24V locking
hardware
requires PoE
or a 24V
power supply.
12V (WET)
24V (WET)
DRY
External Power Input for backup or if
PoE not available. 12V @ 2A (min) or
24V @ 1A (min). 24V required if locking
hardware requires 24V.
WIEGAND
READER
–
+
12V FAIL
SECURE
DOOR
STRIKE
DOOR
CONTACT
Mounting Instructions
Install Single Door Controller onto electrical box using provided 6-32 screws or on drywall using provided anchors and
screws.
For a standard US 1-gang box:
1. Use two 6-32 screws (A) to attach backplate (B) to gang box
Recommended: Use the provided drywall screws (C) and anchors (not shown) on drywall for added stability
2. Snap on main housing (D) to backplate (B)
• On the right side of the main housing (D), ensure that the two edge clips fit into
their respective notches on the backplate (B)
• Press firmly on the main housing (D) to snap into place
3. Partially unscrew pre-installed M4 set screw (E) to secure
main housing (D) to backplate (B)
4. Use the cable slot (F) to hold cables while wiring
5. Snap on front cover (G)
End-of-Line Supervision
REX 1-2 and Contact 1-2 have support for
user-installed single or double 1k ohm
termination.
Tamper Sensor
Removal of front cover will trigger tamper
detection during normal operation.
USB Ports
The Single Door Controller has two USB ports that
you can use with Openpath expansion boards.
Expansions require separate power.
SD Slot
Do not remove the SD card unless instructed by Openpath.
WiFi and Device Placement
The Single Door Controller is WiFi-enabled. If using WiFi,
ensure that the SDC is installed within range of an access
point, and is away from sources of noise and interference,
like microwave ovens.
Hard Reset
Warning: Hard Reset will erase all data on device. Only
reset if instructed by Openpath.
1. Remove power
2. Press and hold down Admin button
3. Reconnect power
4. Continue holding Admin button until LED turns solid
yellow (about 30 seconds), then release
STEP 2 VIEW