Ophit WRO-100 User manual

WRO-100
Wireless Router
1 OPHIT CO., LTD.
OPHIT CO., LTD.
USER MANUAL
Model: WRO-100
Rev.1.0

WRO-100
Wireless Router
2 OPHIT CO., LTD.
Table of Contents
1. Connection
2. Operation Mode
3. Internet Settings
4. Wireless Settings
5. Firewall
6. Administration
7. Product Specification and port list of TCP/IP
8. Environmental Conditions for operation
9. Trouble shooting guide & Cleaning Instruction
10. Warranty & Warning
11. Parts

WRO-100
Wireless Router
3 OPHIT CO., LTD.
Symbol Definitions
The Following symbols appear on the product, label or the product packing.
Each symbol carries a special definition, as defined below.
Symbol
Definition
Symbol
Definition
V~
AC Voltage
Consult accompanying
documents
S/N :
Serial Number
Underwriters Lavatories(UL) Classification:
MEDICAL EQUIPMENT
WITH RESPECT TO ELECTRIC SHOCK FIRE, AND MECHANICAL
HAZARDS ONLY IN ACCORDANCE WITH UL60601-1/CAN/CSA
C22.2 No. 601.1 45MG
Indicates proof of conformity to applicable European Economic Community
Council directives and to harmonized standards published in the official journal
of the European Communities.
Tested to comply with FCC Class B standard.
This symbol indicates that the waste of electronic equipment must not be
disposed as unsorted municipal waste and must be collected separately.
Please contact the manufacturer or other authorized disposal company to
decommission your equipment.
- IEC60601-1 (EN60601-1, Safety of Medical Equipment)
- IEC60601-1-2 (EN60601-1-2, Electromagnetic Compatibility Requirements)
* Class A for Noise-emission, and Level B for Noise-immunity

WRO-100
Wireless Router
4 OPHIT CO., LTD.
Safety Instructions
Please read the following safety instructions as they are designed to prevent damage to property and
harm to the user.
“Warning”Indicates the presence of a hazard that could result in severe personal injury, death
Or substantial property damage if ignored.
An exclamation mark within a triangle is intended to alert the user to the presence of important
Operating and maintenance instructions in the manual.
Caution
“Caution”indicates the presence of the hazard that could result in minor injury, or property
Damage if ignored.
NOTE
“Note”describes information for the installation, operation, or maintenance of which is
Important but hazard related if ignored.
*This device is built to connect a medical device to medical facilities
router/routers or to network system for data transferring. WRO-100 can be
connected to medical devices wirelessly and also using LAN cable.

WRO-100
Wireless Router
5 OPHIT CO., LTD.
1. Connecting to WRO-100 Setting Page
Open Windows explorer and connect to 10.10.10.254 (WRO-100 default IP address)
Input User name/ Password
User name: admin / Password: admin
Initial Setup screen will appear as below.

WRO-100
Wireless Router
6 OPHIT CO., LTD.
2. Operation Mode
Default Value is Gateway Mode and normally changing Mode is not recommended except for Technicians
or Engineers.

WRO-100
Wireless Router
7 OPHIT CO., LTD.
3. Internet Settings
WAN
Configured when using VDSL/ADSL (Dynamic IP) or Cable modem.
NOTE
DHCP(Auto configuration)
Configured when VDSL, LAN, Cable, ADSL Service.
Dynamic IP is automatically configured form Modem, and you can check
WAN IP at Administration/Status menu.

WRO-100
Wireless Router
8 OPHIT CO., LTD.
Configured when ADSL Modem (Dynamic IP) and PPPoE Connection
(ID and Password is needed when connecting to Internet)
NOTE
PPPoE Setting
On PPPoE setting you need ID and Password.
ID and Password is delivered form ISP (Internet Service Provider).
ISP may provide IP address to connect. In this case you can input IP
Address

WRO-100
Wireless Router
9 OPHIT CO., LTD.
Static IP
Static IP Address
1. Input IP address provided by ISP
2. Click “Apply” to save.
If you do not click “Apply” data will not be saved after rebooting.
WRO-100 Wireless Feature Description
You can select SSID (Ophit) in Windows98, Me, 2000, vista, 7, 8 in the Wireless setup driver on your PC.
(Mostly you can find it on the lower right corner of you window screen, double click to configure and
activate)
Example

WRO-100
Wireless Router
10 OPHIT CO., LTD.
How to connect wireless LAN card to WRO-100 in Windows 8
If you want to activate connection on Windows 8’s wireless LAN setup refer to the below pictures in this
page.
For reference there is a Wi-Fi quick access switch on some LAPTOP/PC, you can set it on to activate
Wireless LAN or in some LAPTOP PC you can set it on by function Key.
Control Panel Network and Internet Network Connection Wireless Network Connection (Wi-Fi),
Click Mouse Right button Click Connect / Disconnect Click/Select ‘Ophit’Click Connect Button

WRO-100
Wireless Router
11 OPHIT CO., LTD.
LAN
IP Address: WRO-100 IP setting. Factory default setting Gateway is 10.10.10.254.
DHCP Type: Automatic setting for IP address for PC. Select Default value.
Range of IP Address: Automatic IP address setting by server and configures the range of IP address.

WRO-100
Wireless Router
12 OPHIT CO., LTD.
Advanced Routing
Routing Table
Configure for Internal LAN of AP to other Network.
Add HOST
If you want to add HOST, you can select type of HOST.
Add Host IP to destination.
Adding Routing table to designated Host’s LAN’s Gateway address.
Click "Apply" button and you can input the Routing table of HOST.
Adding Network
You can set type of NET when you want add Network.
Input Network address and Net mask to destination.
Input Gateway address of LAN to Routing table of Dedicated NET.
Click "Apply" and then Routing table for NET.
Table Initialization
If you click "Initialization" button, all the value setting will go back to default value.

WRO-100
Wireless Router
13 OPHIT CO., LTD.
4. Wireless Settings
Basic
You can configure basic wireless settings including Network Name (SSID), etc.

WRO-100
Wireless Router
14 OPHIT CO., LTD.
Security
Security option list: Open system, Sharing Key, Automatic, WPA, WPA2, WPA-PSK, WPA2-PSK
Open System
No Use for Securities
Shared
Setup with pre-defined Key value, Technology of WEP
WEPAUTO
Using both Open System and Sharing Key
WPA2-PSK
Most Powerful Security in Wi-Fi standard
Apply button
If there’s changes you must click “Apply” button to update and save
NOTE
If you do not use Wireless Security function, other users may connect to
WRO-100 and use internet or control your PC.
Most powerful wireless security is WPA2-PSK mode. When activating
WPA2-PSK you must always remember the password.
Windows XP: Version should be above Service Pack 2.
With Windows 98, ME, 2000, driver installed on PC should support
WPA2-PSK password.
If there are other APs near WRO-100, 2.4GHz frequency channel may be
interrupted and with other Aps. Normally WRO-100 uses channel 6, if you
find out channel 3~9, you’d better change channel as below.
Channel Search program is installed in the Wireless LAN card driver.
Other channel + 3 examples) If other AP’s channel is 4 ,you’d better
change channel as 7.(4+3 = 7)
Other channel –3 example) If other AP’s channel is 8 ,you’d better

WRO-100
Wireless Router
15 OPHIT CO., LTD.
change channel as 5 .(8–3 = 5)
WEP Mode setup security
Change security mode as “WEPAUTO” →Input WEP KEY1~4 in 10 digit letter or 26 digit numeric.
You must remember this Key1~4 value
If you want string, you can change Hex to ASCII at the drop box on the right side of WEP Key input box.
You can input 5 digit letter or 13 digit numeric.

WRO-100
Wireless Router
16 OPHIT CO., LTD.
On Windows
Control Panel Network and Internet Network Connection Wireless Network Connection (Wi-Fi),
Click Mouse Right button Click Connect / Disconnect Click ‘Ophit’Click Connect Button
Input network Key password Click Connect
If ‘Connected” message shows up, you are successfully connected (Do not forget network key)

WRO-100
Wireless Router
17 OPHIT CO., LTD.
WPA-PSK Security
Security Mode SettingSelect WPA / TKIP - > Input Network Key “Click Apply”
Network Key is determined by User.
(Do not forget Network Key.)

WRO-100
Wireless Router
18 OPHIT CO., LTD.
5. WDS
WRO-100 WDS Setting
Set IP as 10.10.10.xxx on connecting device (setting IP of the device in the same network area but
different IP with WRO-100 for connection) and open Internet Explorer.
After getting connected to WRO-100 AP on wireless, type 10.10.10.254 on explorer and then press enter
to be connected on setting page. (User name/Password: admin/admin)
Go to Wireless Distribution System Setting page by clicking WDS on Menu
-Default value is set as “Disable”. Select “Bridge Mode”, “Repeater Mode” for Main AP and “Lazy
Mode”, “Repeater Mode” for Slave AP.
-Wi-Fi can’t be searched from device when set on “Bridge Mode” because Wireless works through
WAN port. Please check your settings before applying because device has to be connected by
cable to be connected.
-Repeater Mode is a mode using AP and Bridge simultaneously. MAC address of AP needs to be
inputted when setting Bridge Mode and Repeater Mode. MAC address can be found on Local
Network box of Status page.

WRO-100
Wireless Router
19 OPHIT CO., LTD.
On “Lazy Mode”, Mac Address registered on Master AP is used so you don’t need to input MAC address.
Radio frequency channel needs to be same and IP of AP needs to be set as different IP on same range
when setting WDS. (Master AP : 10.10.10.254, Slave AP : 10.10.10.253)
If DHCP Type is set as “Server” you need to change setting to “Disable”.
When setting WDS there are CCK, OFDM, HTMIX, GREENFIELD in “Phy Mode”
CCK : 802.11b OFDM : 802.11g HTMIX : 802.11b/g/n GREENFIELD : 802.11n
Phy Mode and Encryp Type needs to be set same on connecting AP.

WRO-100
Wireless Router
20 OPHIT CO., LTD.
On “AP Mac Address” input AP Mac Address of device you will connect.
After setting is done click “Apply” and then reboot, Device must be rebooted for WDS function to operate.