Opt PD3000-RGB User manual

PD3000-RGB
PD4000-RGB PD9000-RGB
PD5000-RGB PD10000-RGB
PD6000-RGB PD12000-RGB
PD7000-RGB PD15000-RGB
PD20000-RGB PD25000-RGB
PD26000-RGB PD30000-RGB
USER MANUAL
Noce
AVOID EYE OR SKIN EXPOSURE TO
DIRECT OR SCATTERED LIGHT
CLASS 4 LASER PRODUCT
Manufactured/ Cerfied by
Shenzhen Optlaser Technologies Co.,Ltd
Thank you for purchasing our products, please take some minutes to read this manual
before operang any of these laser projectors!
PD8000-RGB
.......
www.optlaser.com

Content
INTRODUCTION
PACKING LIST
UNPACKING INSTRUCTIONS
GENERAL INFORMATION
SAFETY NOTES
LASER AND SAFETY NOTES
LABELLING REFERENCE
PROPER USAGE
RIGGING
OPERATIONS
INTERLOCK DIAGRAM
LCD Display Seng introducon
PD3 SERIES
INTRODUCTIONS of PD3 SERIES
Specificaons of PD3 SERIES
PD6 SERIES
INTRODUCTIONS of PD6 SERIES
Specificaons of PD6 SERIES
PD8 SERIES
INTRODUCTIONS of PD8 SERIES
Specificaons of PD8 SERIES
PD20 SERIES
Display mode introducon
SD Card Introducon
DMX CHART
FB4 integrated Devices
INTRODUCTIONS of FB4 INTEGRATED DEVICES
INTRODUCTIONS OF RE-ALIGNMENTS. REF.
Maintenance Instrucon
Aer sale service and warranty
2
2
2
2
3
4
5, 6
7
7
8, 9
10
11
12
13
14
15
16
17
18
19
20
21
22
Specificaons of PD20 SERIES
23
23
24, 25
26
27
28, 29
30
30

INTRODUCTION
Thank you for purchasing our products. To opmize the performance of your laser, please read these
operang instrucons carefully and familiarize yourself with the basic operaons of this system. These
instrucons contain important safety informaon regarding the use and maintenance of this system as well.
Please keep this manual with the unit, for future reference. If you sell this product to another user, be sure
that they also receive this document.
Noce
We are constantly striving to improve the quality of our products. As such, the content of this
manual may be changed without noce.
We have tried our best to guarantee the accuracy of this manual. If you have any quesons or find
any errors, please contact us directly to help correct this.
UNPACKING INSTRUCTIONS
Open the package and carefully unpack everything inside.
Ensure all parts are present and in good condion.
Do not use any equipment that appears to be damaged.
If any parts are missing or damaged then please immediately nofy your carrier or local distributor.
GENERAL INFORMATION
The following chapters explain important informaon about lasers in general, basic laser safety and
some ps about
how to use this device correctly. Please read this informaon as it contains crical
informaon you must be aware of, prior to using this system.
PACKING LIST
LASER projector
Name Qty(pcs)
1
AC power cord 1
Keys for Key switch 2
Power output connector 1
Remote Interlock connector 2
Allen key 1
2

WARNING! This projector is a Class 4 laser product. It must never be used for audience-scanning
applicaons. The output beam of the projector must always be at least 3 meters above the floor in the
audience. See the Operang Instrucons secon for further informaon.
Please read the following notes carefully! They include important safety informaon about the
installaon, usage, and maintenance of this product.
SAFETY NOTES
Keep this User Manual for future consultaon. If you sell this product to another user, be sure that they also receive
this document.
Always make sure that the voltage of the outlet to which you are connecng this product is within the range stated on
the decal or rear panel of the product.
This product is not designed for use outdoors in adverse weather condions. To prevent risk of fire or shock, do not
expose this product to rain or moisture.
Always disconnect this product from the power source before cleaning it or replacing the fuse.
Make sure to replace the fuse with another of the same type and rang.
If mounng it overhead, always secure this product to a fastening device using a safety chain or cable.
In the event of a serious operang problem, stop using the projector immediately. Never try to repair the unit except in
a controlled environment under trained supervision. Repairs carried out by unskilled people can lead to damage or
malfuncon of the unit, as well as exposure to dangerous laser light.
Never connect this product to a dimmer pack.
Make sure the power cord is not crimped or damaged.
Never disconnect the power cord by pulling or tugging on the cord.
Never carry a product from the power cord or any moving part. Always use the hanging/mounng bracket or the
handles.
Always avoid eye or skin exposure to direct or scaered light from this product.
Lasers can be hazardous and have unique safety consideraons. Permanent eye injury and blindness is possible if lasers
are used incorrectly. Pay close aenon to each safety REMARK and WARNING statement in this user manual. Read all
instrucons carefully BEFORE operang this device.
Never intenonally expose yourself or others to direct laser light.
This laser product can potenally cause instant eye injury or blindness if laser light directly strikes the eyes.
It is illegal and dangerous to shine this laser into audience areas, where the audience or other personnel could get direct
laser beams or bright reflecons into their eyes.
It is a US Federal offense to shine any laser at aircra.
No service allowed by customer. There are no user serviceable parts inside the unit. Do not aempt any repairs
yourself.
Service is only to be handled by the factory or authorized factory trained technicians.
Product is not to be modified by the customer.
Cauon – use of controls or adjustments or performance of procedures other than those specified herein may result
in hazardous radiaon exposure.
3

LASER AND SAFETY NOTES
STOP AND READ ALL THE LASER SAFETY NOTES BELOW
Laser Light is different from any other light sources with which you may be familiar. The light from this
product can cause eye and skin injury if not set up and used properly. Laser light is thousands of mes
more concentrated than light from any other kind of light source. This concentraon of light can cause
instant eye injuries, primarily by burning the rena (the light sensive poron at the back of the eye). Even
if you cannot feel “heat” from a laser beam, it can sll potenally injure or blind you or your audience. Even
very small amounts of laser light are potenally hazardous even at long distances. Laser eye injuries can
happen quicker than you can blink. It is incorrect to think that because these laser entertainment products
use high speed scanned laser beams, that an individual laser beam is safe for eye exposure. It is also
incorrect to assume that because the laser light is moving, it is safe. This is not true.
Since eye injuries can occur instantly, it is crical to prevent the possibility of any direct eye exposure. It is
not legal to aim this laser projector into areas where people can be exposed. This is true even if it is aimed
below people’s faces, such as on a dance floor.
Do not operate the laser without first reading and understanding all safety and technical data in this
manual.
Always set up and install all laser effects so that all laser light is at least 3 meters (9.8 feet) above the
floor on which people can stand. See the “Proper Usage” secon later in this manual.
Aer set up, and prior to public use, test the laser to ensure proper funcon. Do not use if any
defect is detected.
Laser Light - Avoid Eye or Skin Exposure to Direct or Scaered Light.
Do not point lasers at people or animals.
Never look into the laser aperture or laser beams.
Do not point lasers in areas where people can potenally be exposed, such as uncontrolled
balconies, etc.
Do not point lasers at highly reflecve surfaces, such as windows, mirrors and shiny metal objects.
Even laser reflecons can be hazardous.
Never point a laser at aircra, as this is a US Federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output opc (aperture) to cleaning chemicals.
Do not use the laser if the housing is damaged, open, or if the opcs appear damaged in any way.
Never leave this device running unaended.
In the United States, this laser product may not be purchased, sold, rented, leased or loaned for
use unless the recipient possesses a valid Class 4 laser light show variance from the US FDA CDRH.
This product must always be operated by a skilled and well-trained operator who is familiar with the
data included in this manual. Note that use of this projector in the United States also requires a
valid Class 4 laser light show variance from the CDRH as stated above.
The legal requirements for using laser entertainment products vary from country to country. The
user is responsible for the legal requirements at the locaon/country of use.
Always use appropriate lighng safety cables when hanging this projector overhead.
4

LABELLING REFERENCE
5

Laser wavelength nm( )
R 637 638
G 520 532
B 445 465
Total P ow er:
A C Powe r Su ppl y 100-120V 100-24 0 V 20-240V , 50 -6 0Hz
NE VER A IM AT AI RCRAFT, IT IS UNS AFE A ND I LLEGA L
In c ompli anc e w ith IEC-EN60825- 1 and 2 1 CF R1040.10 & 1040. 11
4
See the following reproducons of the product labels. All these labels must be intact and legible
prior to be used on the projector.
Hazard warning symbol
Aperture steering label
2
6

Stainless steel cable(safety rope)
PROPER USAGE
This product is for overhead mounng only. For safety purposes, this projector should be mounted on
steady elevated plaorms or sturdy overhead supports using suitable hanging clamps. In all cases, you must
use safety cables.
Internaonal laser safety regulaons require that laser products must be operated in the fashion illustrated
below, with a minimum of 3 meters (9.8 .) of vercal separaon between the floor and the lowest laser
light vercally. Addionally, 2.5 meters of horizontal separaon is required between laser light and
audience or other public spaces.
The audience area can be passively protected by sliding the aperture cover plate upwards and fixing it in
proper posion by the two thumb screws.
RIGGING
3 meters
laser beams
Be sure that the structure onto which you are mounng this product can support its weight.
Mount the product securely. You can do this with a screw, a nut, and a bolt. You may also use a mounng clamp if
rigging this product onto a truss. The U-shaped support bracket has three mounng holes which may be used to
secure the clamps to the projector.
Always consider ease of access to the unit before deciding on a locaon for this product
When mounng this product overhead, always use a safety cable.
7

OPERATIONS
PD SERIES units come with diode-based only laser sources and all sources have beam correcon ,thus have
great beam show with analog FULL colors modulaon.
The PD SERIES units can be controlled over ILDA and have a bult-in memory with preset
paerns ,also with SD-card slot for freely programs export onto it, that can be easily
triggered through DMX. They can also be operated in automac and sound-to-light mode.
The laser projector provides a master-slave-mode. Show lasers of the same series (slave
projectors), connected via DMX to a main projector (master projector) project the same
paerns like the master projector.
This Series will be applicable for clubs, bars, and those Small/medium venues or theater
events, pares, business acvies, large venues etc.
“PD series projectors are not supplied with standard "E-Stop Box" and "Remote Interlock bypass"
Instead, a simplified “E-Stop Box” featured with “Mushroom switch” and “Key switch” will be supplied in
the purchase accordingly to request.
The “E-stop Box” is generally with a CAT5 cable of 2m length unless there would be different requests.
If user doesn't need adional "E-Stop Switch", Then the “RJ45 jack interlock connector” should be
insterted into the rear plate of the projector’s INTERLOCK posion(with silkscreen INTERLOCK marking) ,only
by this way user will be able to light up the laser projector during operaons.
8

Several steps to start up the laser projector(s)
1. Use the included power cord to connect the laser device to a proper power outlet(AC100-240V, 50/60Hz)
2. Use one of the included keys( 2 sets included in the package, either one
of them will work) to insert into the key-chassis and switch to the “ON” posion
3. Use one of the the included INTERLOCK connectors to insert into the INTERLOCK posion
on the backplate of the device. (2 x RJ45 connectors(well made) included in the package
Remark: There are 2 posions for INTERLOCK on the backplate of the devices ≥10W
herein, either one of the posions will work(one only posion needs to be with
INTERLOCK connector inserted if the laser projector will be used alone.
Both INTERLOCK posions will work if user wants to daisy chain 2 or
more laser projectors through E-stop box.
4. Turn on the power switch from to , then the laser device will
start output laser light.
INTERLOCK connector
Only pin4 & pin5
short-circuited
will be workable
9
Single INTERLOCK connecon
at standard PD3 SERIES backpanel
Dual INTERLOCK connecons
at standard PD6 SERIES backpanel

E ST OP-
( Mus hro om sw i tch )
Key
1
2
3
4
5
6
7
8
Ca ble to E-sto p box & laser projector
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Laser Projector #1
Laser Projector #2
INTERLOCK PORT#1
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
INTERLOCK PORT#1
INTERLOCK PORT#2
INTERLOCK PORT#2
cable between
projector#1 to projector #2
cable to more
following proectors if in desire
INTERLOCK CONNECTION DIAGRAM
Restart
Power In
E-Stop Box
Indicator(RED light-stay on-Emergency stop)
Indicator(RED light-flash-Key switch off)
Indicator(YELLOW light-flash-cable disconnected)
Indicator(GREEN light-stay on-laser ready emits)
Indicator(RED& GREEN light-flash 8s-laser ready to emit)
Indicator(RED& GREEN light-stay on-laser working)
Green Red Yellow
indicators
There may be a few models of the show systems that do not have the DUAL INTERLOCKS due to the limited space inside the compact
size of the system to have the board assembled, therefore, remote interlock control in a low(daisy-chain) for them is not possible.
Mechanical shutter plate
Laser beams at Galvoscanner’s mirrors
According to safety regulaons in the US, CLASS 4 laser show systems must be equipped with the safety elements such as
mechanical shuer plate to prevent a potenal single laser beam shot.
10
We’re capable of carrying out laser systems with such requirements, upon order request.

LCD Display Seng introducon
DMX Address 1
Show Mode ILD
Program Program 1
SD file No SD
SIZE 80
Phase Invert X+ Y+
Scan Speed 30
DMX STATE Show Mode
Slave Mode Slave
X Phase Posive
Y Phase Posive
Laser Lock Off
Sound sense 80
SD Sound Off
LOAD FLASH Off
Color RGB
R 100
G 100
B 100
Language English
Actual view of the LCD display gets lighten on, you need to rotate the menu knob to choose the needed status then
make the preferable sengs.
DMX Address 1
Show Mode ILD
Program Program 1
SD file No SD
SIZE 80
Phase Invert X+ Y+
Scan Speed 30
DMX STATE Show Mode
Slave Mode Slave
X Phase Posive
Y Phase Posive
Laser Lock Off
Sound sense 80
SD Sound Off
LOAD FLASH Off
Color RGB
R 100
G 100
B 100
Language English
DMX Address 1
Show Mode ILD
Program Program 1
SD file No SD
SIZE 80
Phase Invert X+ Y+
Scan Speed 30
DMX STATE Show Mode
Slave Mode Slave
X Phase Posive
Y Phase Posive
Laser Lock Off
Sound sense 80
SD Sound Off
LOAD FLASH Off
Color RGB
R 100
G 100
B 100
Language English
Note:
All the contents listed on the LCD display can be freely changed to the preferable status. The most important
step is to “double-click” the menu knob to SAVE the preferred status when all selecons/sengs get done.
(The other sengs should be operated step by step as DMX seng reference as the guidance following)
e.g. Default Status Click the DMX column once and
manually rotate the menu knob
to change the DMX address(1-17 for
opons)
Double-click the menu knob
to save the preferred status.(When
this step done, the background
of the status will turn to red)
1
23
Important Remark:
While there’s no ILDA signal input and if you don’t need the devices to run in AUTO mode, you can make the seng on “DMX STATE” from
“Show-Mode” switching to “Black OutI” , then will bypass the “AUTO mode”.
11

Front Rear
Side Top view
PD3 SERIES
Standard Verisons(without FB4 built-in)
12

1
2
3
4
5
6
7
8
9
10
11
12
13
14
1 Laser aperture (covered by masking plate)
DO NOT look directly into this aperture once the masking plate gets loosen
When this indicator is lit up the laser system is ready to emit the laser
radiaon as soon as it receives instrucons from control soware.
Laser Emission
LCD Display
2
3
4
5
6
7
8
9
10
11
12
13
14
Integrated with mul sengs on the projector, please refer to detailed
sengs (on Page 11. ) for the LCD
ILDA Input & Output
DMX Input & Output
PowerCON Input & Output
MicroPhone
INTERLOCK (RJ45 jack)
Power Switch
FUSE
Keyhole
Menu knob for LCD Seng
SD-Card Slot
Safety Ring
DB25 connecons input and output for ILDA mode display
3-pin DMX connecons input and thru for DMX512 mode display
Power connecons input and output
Sound receiver
Laser output is available only when the interlock is connected.
It could be used to connect a laser emergency switch(E-stop box).
Power On/Off
Safety element; current rang 4amps
Key Switch, laser output is available when the key is moved to posion “on”
The knob for the main sengs on LCD, click it to wake the LCD and rotate
it for corresponding status seng
Slot for SD-Card which you may have your own laser files to export on
The ring for enwinding a safety rope when the laser device will be installed
on out-of-reach locaons.
INTRODUCTIONS of PD3 SERIES
13

Type of Laser Pure diode-based full colors(semiconductor diode laser systems)
Laser Classificaon Class 4
Laser Power
PD3000-RGB
PD4000-RGB
PD5000-RGB
PD6000-RGB
638nm 520nm 445nm
R/650mW+G/900mW+B/1500mW
R/1200mW+G/900mW+B/1800mW
R/1500mW+G/1000mW+B/2500mW
R/1800mW+G/1100mW+B/3100mW
Scanning-system 40 kpps ILDA@8° , Scan angle Max 60°
Beam Size@aperture 2.5*6 mm
Beam Divergence
Modulaon
Power Supply
Power Consumpon
156*224*125mmDimension
Net Weight
<1.1 mRad
90-110W
AC 100-240V, 50/60Hz
4.26 kg
>60 KHz
Controls Auto, Sound to light, SD-Card, DMX512 , ILDA
Keyed interlock, emission delay, magnec interlock, scan-fail safety,
mechanical shuer(on request), adjustable aperture masking plate.
Safety elements
Operaon Temperature minus 20℃ to 40℃
Protecon Rang IP54
Due to Advanced Opcal Correcon technology used in our laser
systems the opcal power output of each laser colour within the
system may slightly differ from the specificaon of respecve laser
module(s) installed. This does not affect the total guaranteed power
output.
Important statement
Specificaons of PD3 SERIES
14

PD6 SERIES
Standard Verisons(without FB4 built-in)
This enclosure covers RGB laser power rated 7W, 8W, 9W and 10W
300mm
280mm
260mm
220mm
165mm
15

1 Laser aperture (covered by masking plate)
DO NOT look directly into this aperture once the masking plate gets loosen
When this indicator is lit up the laser system is ready to emit the laser
radiaon as soon as it receives instrucons from control soware.
Laser Emission
LCD Display
2
3
4
5
6
7
8
9
10
11
12
13
14
Integrated with mul sengs on the projector, please refer to detailed
sengs (on Page 11. ) for the LCD
ILDA Input & Output
DMX Input & Output
PowerCON Input & Output
Color intensity knobs
INTERLOCK (RJ45 jack)
Power Switch
FUSE
Keyhole
Menu knob for LCD Seng
SD-Card Slot
Safety Ring
DB25 connecons input and output for ILDA mode display
3-pin DMX connecons input and thru for DMX512 mode display
Power connecons input and output
R/G/B power intensity adjustment, rotate or an-rotate to adjust power
Power On/Off
Safety element; current rang 4amps
Key Switch, laser output is available when the key is moved to posion “on”
The knob for the main sengs on LCD, click it to wake the LCD and rotate
it for corresponding status seng
Slot for SD-Card which you may have your own laser files to export on
The ring for enwinding a safety rope when the laser device will be installed
on out-of-reach locaons.
Laser output is available only when the interlock is connected.
Both posions can be used to connect a laser emergency switch(E-stop box).
8
134
5
6
9
10
11
12
7
13
14
INTRODUCTIONS of PD6 SERIES
16

Type of Laser Pure diode-based full colors(semiconductor diode laser systems)
Laser Classificaon Class 4
Laser Power
PD7000-RGB
PD8000-RGB
PD9000-RGB
PD10000-RGB
R/2000mW+G/2000mW+B/3000mW
638nm 520nm 445nm
R/3000mW+G/3000mW+B/3000mW
Scanning-system 40kpps ILDA@8° , Scan angle Max 60°
Beam Size@aperture 3.5*6.5 mm
Beam Divergence
Modulaon
Power Supply
Power Consumpon
260*220*150mmDimension
Net Weight
<1.1 mRad
160W 160W 170W 180W
AC 100-240V, 50/60Hz
8.04 kg
>60 KHz
Controls Auto, Sound to light, SD-Card, DMX512 , ILDA
Keyed interlock, emission delay, magnec interlock, scan-fail safety,
mechanical shuer, adjustable aperture masking plate.
Safety elements
Operaon Temperature minus 20℃ to 40℃
Protecon Rang IP54
Due to Advanced Opcal Correcon technology used in our laser
systems the opcal power output of each laser colour within the
system may slightly differ from the specificaon of respecve laser
module(s) installed. This does not affect the total guaranteed power
output.
Important statement
R/2000mW+G/3000mW+B/3000mW
R/3000mW+G/3000mW+B/4000mW
Specificaons of PD6 SERIES
17

360mm
265mm
260mm
353mm
175mm
PD8 SERIES
Standard Verisons(without FB4 built-in)
18

1 Laser aperture (covered by masking plate)
DO NOT look directly into this aperture once the masking plate gets loosen
When this indicator is lit up the laser system is ready to emit the laser
radiaon as soon as it receives instrucons from control soware.
Laser Emission
LCD Display
2
3
4
5
6
7
8
9
10
11
12
13
14
Integrated with mul sengs on the projector, please refer to detailed
sengs (on Page 11. ) for the LCD
ILDA Input & Output
DMX Input & Output
PowerCON Input & Output
INTERLOCK (RJ45 jack)
Power Switch
FUSE
Keyhole
Menu knob for LCD Seng
SD-Card Slot
Safety Ring
DB25 connecons input and output for ILDA mode display
3-pin DMX connecons input and thru for DMX512 mode display
Power connecons input and output
Laser output is available only when the interlock is connected.
BotLaser output is available only when the interlock is connected.
Power On/Off
Safety element; current rang 8amps
Key Switch, laser output is available when the key is moved to posion “on”
The knob for the main sengs on LCD, click it to wake the LCD and rotate
it for corresponding status seng
Slot for SD-Card which you may have your own laser files to export on
The ring for enwinding a safety rope when the laser device will be installed
on out-of-reach locaons.
1
2
3
4
5
6
9
10
Color intensity knobs R/G/B power intensity adjustment, rotate or an-rotate to adjust power
7
8
11 12
13
14
INTRODUCTIONS of PD8 SERIES
19