OPT7 AURA ROCK LIGHT User manual

LED ROCK LIGHT
INSTRUCTION MANUAL
Rock Light
Durable DIY Design
Bluetooth
Control Features
Downloadable
QR Code
for Smartphone
Input Voltage
input Power
16LEDs
DC12V
13 Watts
2 Four-Core Cree per pod
Raw Lumens
Waterproof
Operating Temperature
340 LM(All 8 Pods combined)
IP68(Only Pod)
-5℉~120℉
Simple to Follow
Installation Guide
SPECIFICATIONS

WHAT’S INCLUDED
×8
×8
STEP1
STEP2
STEP3STEP 4
×8 ×1
×16
TWO WAYS TO MOUNT
FLAT /ROUNT INSTALL WITH RUBBER MOUNT
ROCK LIGHT POD FITMENT STEPS
Remember, the rock light pods become extremely hot when in use, so
you will not want to install the pods or control box underneath or on any
sensitive material or power lines under your vehicle for safety.
LIGHT POD
FLAT RUBBER MOUNT ROUND RUBBER MOUNT CONTROL BOX
M4 NUT
M4 SCREW
1.
2.
3.
4.
Make sure the pods are flush with the rubber mounts.
Begin inserting the screws into the screw holes.
Now you’re ready to mount the pods onto your vehicle.
Once the pods are mounted, connect each pod power line to the fuse
box power line ends and tighten the caps together with your fingers.

2.5mm Allen wrench
7mm wrenchor socket
5/32 inch drill bit
WHERE TO INSTALL
1. Choose the mounting locations for each of
the LED pods and the control box. Please refer
to your vehicles owner’s manual for safe areas
to install additional lighting and wiring.
2. Determine where the wires will run through.
If needed, drill a hole(s) for the wire connector
to pass through.
3. Mark and begin drilling each mounting hole
with a 5/32” drill bit.
4. Install the LED Pods by themselves for a flat
install or with the Rubber Mounting Pads for
rounded surfaces.
5. Insert the two 25mm Screws through the
LED Pod screw holes and Rubber Mounting
Pad.
6. Secure the Screw and Pods with the Washers
and Nuts to install flush with the drilled holes.
7. Secure the Pods by tightening the Screws for
a snug fit away from any wiring or moving
parts. Caution: The Pods become very hot
during use, which can cause severe damage to
any electrical, rubber, or moving parts that are
exposed and too close to your Pods. Keep Pods
away from any parts that can be damaged by
extreme heat exposure.
8. Connect all of the Pod Cables to the Splitter
Cable and secure by screwing locking the
collars from the Splitter Cable. Secure the Caps
by tightening the end connections with your
fingers.
9. Connect both sets of Splitter Cable input
wires to the vehicle electrical system using
additional power wire and fuse with fuse
holder. Red is positive (+). Black is negative (-).
10. Once the Pods and Control Box electrical
wiring are all safely connected to your vehicle’s
electrical system, you can now begin using the
Rock Light Pods with the Bluetooth App on
your Smartphone. Feel free to share a review
of your installation with info about your exact
off-road vehicle so other customers
understand too! Rock on!
TOOLS REQUIRED
FRONT
REAR
Rock Light Pods Recommended Locations
INSTALLATION STEPS

HOW TO USE THE APP
Once you’ve downloaded the PRO RGB App, you will then turn on your
Smartphone’s Bluetooth connection and connect to the app. (See Figure 1)
You can use the App for up to 30 feet away from your vehicle.
PRO RGB LIGHTING APP
ROCK LIGHT FREE DOWNLOADABLE APP
COMPATIBLE WITH:
Download the free
PRO RGB app by taking
a photo of the QR
Code below, or go to
either of these links:
Android 4.4 or later
https://play.google.com
/store/apps/details?id=
cs.com.testbluetooth
64.2 mm (2.53 inch)
72.5 mm (2.85 inch)
40.3 mm
(1.59 inch)
4.2 mm
(0.17 inch)
LED ROCK LIGHT POD DIMENSIONS
We provide you with 3 control methods for you to choose. You can quickly click the "Control"
button at the bottom of the screen to easily control the style you want. (See Figure 2)
You can also click the "Setting" button to view the detailed information
described in "GUIDE". (See Figure 3 & 4)
IOS 9.0 or later
https://apps.apple.com
/us/app/pro-rgb/
id1485141574
1
2
Figure 1 Figure 2 Figure 3 Figure 4