OPT7 Aura User manual

LED BOAT INTERIOR LIGHT
INSTRUCTION MANUAL
Boat Light
Durable DIY Design
Bluetooth
Control Features
Downloadable
QR Code
for Smartphone
Input Voltage
input Power
12LEDs
DC12~24V
9.6 Watts
3 Tri-Core Cree per pod
Raw Lumens
Waterproof
Operating Temperature
400 LM(All 4Pods combined)
IP68(Only Pod)
-5℉~120℉
HOW TO USE THE APP
Once you’ve downloaded the BLEDIM App, you will then turn on your
Smartphone’s Bluetooth connection and connect to the app.
You can use the App for up to 30 feet away from your boat.
BLEDIM APP BUTTONS
BOAT LIGHT FREE DOWNLOADABLE APP
IOS 7.0 Android 4.3
Download the free
BLEDIM app by taking
a photo of the QR
Code below, or go to
either of these links:
1.
2.
3.
4.
5.
6.
https://apps.apple.co
m/us/app/bledim/id1
027450939
https://play.google.com
/store/apps/details?id=
com.forwell.bledim
Click Top Left Bluetooth Icon.
Search the Bluetooth devices and it will appear the name of
“Bluetooth_Dimmer”.
Click to connect it., and then the connection will successful .
Begin using the color listings to change the LED colors.
12
5
3
4 6
OTHER MENU SETTINGS
Simple to Follow
Installation Guide
SPECIFICATIONS
Power button
Quick Connect
Scene Modes
DIY Mode
Controlling mode
SoundSync Mode
TM
64.2 mm (2.53 inch)
72.5 mm (2.85 inch)
40.3 mm
(1.59 inch)
4.2 mm
(0.17 inch)
LED BOAT LIGHT POD DIMENSIONS

WHAT’S INCLUDED
×4
×1
STEP1
STEP2
STEP3STEP 4
×1 ×1
×8
2.5mm Allen wrench
7mm wrenchor socket
5/32 inch drill bit
TWO WAYS TO MOUNT
FLAT /ROUNT INSTALL WITH RUBBER MOUNT
BOAT LIGHT POD FITMENT STEPS
WHERE TO INSTALL
1. Choose the mounting locations for each of
the LED pods and the control box. Please refer
to your boat owner’s manual for safe areas to
install additional lighting and wiring.
2. Determine where the wires will run through.
If needed, drill a hole(s) for the wire connector
to pass through.
3. Mark and begin drilling each mounting hole
with a 5/32” drill bit.
4. Install the LED Pods by themselves for a flat
install or with the Rubber Mounting Pads for
rounded surfaces.
5. Insert the two 25mm Screws through the
LED Pod screw holes and Rubber Mounting
Pad.
6. Secure the Screw and Pods with the Washers
and Nuts to install flush with the drilled holes.
7. Secure the Pods by tightening the Screws for
a snug fit away from any wiring or moving
parts. Caution: The Pods become very hot
during use, which can cause severe damage to
any electrical, rubber, or moving parts that are
exposed and too close to your Pods. Keep Pods
away from any parts that can be damaged by
extreme heat exposure.
8. Connect all of the Pod Cables to the Splitter
Cable and secure by screwing locking the
collars from the Splitter Cable. Secure the Caps
by tightening the end connections with your
fingers.
9. Connect both sets of Splitter Cable input
wires to the boat electrical system using
additional power wire and fuse with fuse
holder. Red is positive (+). Black is negative (-).
10. Once the Pods and Control Box electrical
wiring are all safely connected to your boat’s
electrical system, you can now begin using the
boat Light Pods with the Bluetooth App on your
Smartphone. Feel free to share a review of
your installation with info about your exact
boat so other customers understand too!
Rock on!
Remember, the boat light pods become extremely hot when in use, so
you will not want to install the pods or control box underneath or on any
sensitive material or power lines under your boat for safety.
TOOLS REQUIRED
FRONT
REAR
Boat Light Pods Recommended Locations
INSTALLATION STEPS
LIGHT POD
FLAT RUBBER MOUNT ROUND RUBBER MOUNT CONTROL BOX
WASHER
M4 NUT
M4 SCREW
1.
2.
3.
4.
Make sure the pods are flush with the rubber mounts.
Begin inserting the screws into the screw holes.
Now you’re ready to mount the pods onto your boat.
Once the pods are mounted, connect each pod power line to the fuse
box power line ends and tighten the caps together with your fingers.