OPTIX LCDQUAD4SW User manual

IMAGE
PROCESSOR
OPTIMIZE YOUR SENSES
MODEL : LCDQUAD4SW

TABLE OF CONTENTS
2
INTRODUCTION
Contents
DEVICE
Remotes
INSTALLATION
Camera Pins
Wiring
PROGRAMMING
Camera Setup
Camera Naming
OSD Setup
System Setup
Trigger Setup
Trigger Priority
Reset
3
3
4
6
DISPLAY MODES 9
MODEL : LCDQUAD4SW

3
INTRODUCTION
CONTENTS
1 - Image Processor Module
1 - Power Cable
1 - IR Remote Control
1 - Wired Remote Control (Oponal)
1 - Live Video Out Cable
4 - Camera Cables
Congratulaons on your purchase of the Opx 360 “Image Processor”. With this image processor you can watch up to 4
different camera inputs. Priority can be given to specific cameras depending on needs, with trigger inputs to allow
images to be shown when using turn indicators, reversing, etc, with split, PIP display modes. Recording is supported
when connected to an oponal DVR.
DEVICE
VIDEO IN POWER IN VIDEO REC
OUT
LIVE VIDEO
OUT
AUDIO IN CAM. 2 IN
AUDIO REC
OUT
WIRED REMOTE
IN
CAM. 4 IN
CAM. 1 IN CAM. 3 IN
MODEL : LCDQUAD4SW

4
DEVICE
INSTALLATION
WIRED REMOTE IR REMOTE
UP / FRONT CAM
DOWN / REAR CAM
RIGHT / RIGHT CAM
DISPLAY MODE / NEXT
MENU ENTER / EXIT
CONNECTOR TO KEY IN
LEFT / LEFT CAM
MUTE
SPEAKER ON / OFF
(BACKSIDE)
AV ENTER / EXIT
JUMP KEY
CAF
CAB
CARCAL
QUADAV
MENUJUMP
CAF
CAB
CARCAL
MENU
MODE
REST
SEL
IMG
P/N
AV
LEFT / LEFT CAM
DISPLAY MODE / NEXT
IMAGE RESERVE
MENU ENTER / EXIT
JUMP KEY
RESET
UP / FRONT CAM
RIGHT / RIGHT CAM
PAL / NTSC SELECTOR
A/V ENTER / EXIT
POWER ON / OFF
DOWN / REAR CAM
MODEL : LCDQUAD4SW
POWER
GROUND
VIDEO
AUDIO
CAMERA OUTPUT 4 PIN KEY IN
POWER
N/A
GROUND
N/A
I.R.
1
1
2
4
32
3
4
5

5
MODEL : LCDQUAD4SW
INSTALLATION
DVD VIDEO WIRED REMOTE MONITOR
VIDEO OUT
AUDIO
AUDIO RECORD OUT
VIDEO
Red (+)
(-)
(+)
(+)
(+)
(+)
(+)
(+)
Black
White
Green
Blue
Brown
Yellow
Orange
12v+ In
Ground In
Le Camera Trigger
Front Camera Trigger
Right Camera Trigger
Back Camera Trigger
Double Split Trigger
Not Used
POWER CABLE
CAMERA 1 IN
CAMERA 2 IN
CAMERA 3 IN
CAMERA 4 IN
CAF
CAB
CARCAL
QUADAV
MENUJUMP
MONITOR

6
MODEL : LCDQUAD4SW
OPTION PROGRAMMING
CAMERA SETUP
1. Press Menu to enter Menu mode.
2. Press CAF / CAB / SEL(JUMP) to select “CAMERA SETUP”, then press CAL / CAR to enter.
3. Press CAL / CAB to select the camera to adjust (Le, Right, Front, or Back)
4. Press CAF / CAB / SEL(JUMP) to choose the opon to adjust the following opons:
CAMERA NAMING
1. Press Menu to enter Menu mode.
2. Press CAF / CAB / SEL(JUMP) to select “CAMERA NAME”, then press CAL / CAR to enter.
3. Press CAF / CAB / SEL(JUMP) to select the camera to adjust (default name of each is Le, Right, Front, Back)
To rename the camera the leers can be revised by pressing CAL/CAR. Pressing CH- will select the next character
to a maximum of 62 characters
4. Press CAF / CAB / SEL(JUMP) to select “DISP”, then press CAL / CAR to select ON or OFF. When set to ON, the
camera name will be displayed in the window view of each camera.
0-100
0-100
0-100
<OFF - Normal> <H-V -Upside Down> <V - Upside Down Reverse> <H - Reversed>
<ON - the ens cover is open all the me> <OFF - the lens cover only opens when
reverse trigger is acve>
CONTRAST :
COLOR :
HUE :
MIRROR :
MOTO-CAM :

7
MODEL : LCDQUAD4SW
OPTION PROGRAMMING
OSD SETUP
1. Press Menu to enter Menu mode.
2. Press CAF / CAB / SEL(JUMP) to select “OSD SETUP”, then press CAL / CAR to enter.
3. Press CAF / CAB / SEL(JUMP) to choose the opon to adjust the following opons:
<ON - Distance Guide shown> <OFF>
<ON> <OFF>
<ON> <OFF>
<ON - will show turn indicator when trigger is detected> <OFF>
<WHITE> <BLACK> <GRAY>
REAR GUAGE :
OSD LOCK :
AUTO BRIGHTNESS :
TURN MARKER :
BOUNDARY COLOR :
SYSTEM SETUP
1. Press Menu to enter Menu mode.
2. Press CAF / CAB / SEL(JUMP) to select “SYSTEM SETUP”, then press CAL / CAR to enter.
3. Press CAF / CAB / SEL(JUMP) to choose the opon to adjust the following opons:
<QUAD> <LEFT> <RIGHT> <FRONT> <BACK>
<ON - Will auto switch between cameras(no signal on input is automacally skipped)> <OFF>
1 - 60 Seconds
“JUMP” key will switch to the following camera views. <L / R> <F / B> <L+R / F> <B + L / R>
<LEFT> <RIGHT> <FRONT> <BACK> <QUAD> <L / R> <F / B> <L+R / F> <B + L / R> <AV>
<STANDARD> <BRIGHT> <SOFT>
<NTSC< <PAL>
REC V OUT :
SCAN :
SCAN DELAY :
JUMP KEY :
POWER ON CAM :
DVD IMAGE :
TV SYSTEM :

8
MODEL : LCDQUAD4SW
OPTION PROGRAMMING
TRIGGER SETUP
1. Press Menu to enter Menu mode.
2. Press CAF / CAB / SEL(JUMP) to select “TRIGGER SETUP”, then press CAL / CAR to enter.
3. Press CAF / CAB / SEL(JUMP) to choose the opon to adjust the following opons:
<SINGLE - Displays image from L or R trigger source> <DUAL - Shows L + R camera images>
<BACK - Displays image from B when reversing>
<B + L / R (Shows Back, Le, and Right camera images when reversing>
0-60 Seconds (Image will remain on for me selected aer trigger is removed)
<LEFTWARD> Choose image to be on channel<RIGHTWARD> Choose image to be on channel
<AUDIO> Choose the channel which audio will come from.
TURN IMAGE :
BACKUP DISPLAY :
TRIGGER OFF DELAY :
DUPLEX SPLIT DISPLAY :
TRIGGER PRIORITY
1. Press Menu to enter Menu mode.
2. Press CAF / CAB / SEL(JUMP) to select “TRIGGER PRIORITY”, then press CAL / CAR to enter.
3. Press CAF / CAB / SEL(JUMP) to choose the opon to adjust the following opons:
<LEFT> <RIGHT> <FRONT> <BACK> <DUAL>
<LEFT> <RIGHT> <FRONT> <BACK> <DUAL>
<LEFT> <RIGHT> <FRONT> <BACK> <DUAL>
<LEFT> <RIGHT> <FRONT> <BACK> <DUAL>
<LEFT> <RIGHT> <FRONT> <BACK> <DUAL>
1ST PRIORITY :
2ND PRIORITY :
3RD PRIORITY :
4TH PRIORITY :
5TH PRIORITY :
RESET
1. Press Menu to enter Menu mode.
2. Press CAF / CAB / SEL(JUMP) to select “RESET”, then press CAL / CAR to reset all sengs to default.

9
MODEL : LCDQUAD4SW
DISPLAY MODES
LEFT RIGHT
BACK
FRONT
B + L / R
QUAD
L + R / F
L / R
F / B