optonica 7318 User manual

Infrared Motion Sensor
SKU: 7318
Instruction
Thank you for purchasing Infrared Motion Sensor!
The product adopts good sensitivity detector and integrated circuit. It gathers automatism,
convenience, safety, saving-energy and practical functions. It utilizes the infrared energy from
human as control-signal source and it can start the load at once when one enters detection field. It
can identify day and night automatically. It is easy to install and used widely.
SPECIFICATION:
Power Source: 220-240V/AC Detection Range: 180°
Power Frequency: 50/60Hz Detection Distance: Wall Mounting16m max(<24℃)
Ambient Light: <10/2000LUX (adjustable) Ceiling Mounting10m max(<24℃)
Other Functions: D2D: DUSK TO DAWN Working Temperature: -20~+40℃
Always-ON Installation Height: 1.8-2.5m
Time Delay: 10sec/30sec/1Min/5Min/10Min Working Humidity: <93%RH
Rated Load: Max.800W Power Consumption: approx 0.5W
400W LED Detection Moving Speed: 0.6-1.5m/s
FUNCTION :
Can identify day and night: The consumer can adjust working state in different ambient light. It
can work in the daytime and at night when it is adjusted on the “sun” position (max). It can
work in the ambient light less than 10LUX when it is adjusted on the “-” position (min). As for
the adjustment pattern, please refer to the testing pattern.
Photocell function: Adjust the first switch to D2D position,it can fitting into “Dusk to Dawn”
mode. It will work in the ambient light less than 30LUX, and auto logout in the ambient light
more than 100LUX.
Always-On function:Adjust the first switch to ON position,It will lamp will Always-ON.
SENS adjustable: It can be adjusted according to using location. The detection distance of low
sensitivity could be only≈7m and high sensitivity could be≈16m which fits for large room.
Time-Delay is added continually: When it receives the second induction signals within the first
induction, it will restart to time from the moment.
Good Sensitivity Poor Sensitivity
SETTING:
LUX Setting:+ Work day and night，—Only work at night
Sensor Mode LMH: L=Short Detection Distance M=Medium Detection Distance
H=Minimum Detection Distance
D2D Mode:
Off sensor mode,it can fitting into “Dusk to Dawn”mode.
It will work in the ambient light less than 30lux, and auto logout in the ambient light
more than 100lux
ON Mode:
Off movement mode it can fitting into Manual Override Function-Always-ON,the light will
illuminate continuously.
Time Delay Setting: 10S，30S，1min，5min，10Min.
INSTALLATION ADVICE:
As the detector responds to changes in temperature, avoid the following
situations:
Avoid pointing the detector towards objects with highly reflective surfaces, such as mirrors etc.
Avoid mounting the detector near heat sources, such as heating vents, air conditioning units,
light etc.
Avoid pointing the detector towards objects that may move in the wind, such as curtains, tall
plants etc.
CONNECTION:
Warning. Danger of death through electric shock!
Must be installed by professional electrician.
Disconnect power source.
Cover or shied any adjacent live components.
Ensure device cannot be switched on.
Check power supply is disconnected.

Loosen the nail on the bottom and open the front cover. (refer to figure 1 and 2).
Loosen the nail on the back ,fold the cover and then fix it with inflated screw on the selected
position.(refer to the figure 3)
Plug the wire into the hole with gasket, and then connect the wire with connection column
according to Connection-wire diagram.(Note: The wire and the hole gasket should connect
very tightly to make the product waterproof)
Switch on the power and then test it.
Figure 1 Figure 2 Figure 3
It not only can install on the wall directly but also can install on the inner corner with the help of
the widget (refer to the photograph below)
Flat mounted Inner corner mounted
TEST:
Turn the LUX knob clockwise on the maximum (sun);
turn the TIME knob anti-clockwise on the minimum
(10s).
Switch on the power; the sensor and its connected
lamp will have no signal at the beginning. After
Warm-up 30sec, the sensor can start work .If the sensor receives the induction signal, the lamp
will turn on. While there is no another induction signal any more, the load should stop working
within 10sec±3sec and the lamp would turn off.
Turn LUX knob anti-clockwise on the minimum (-). If the ambient light is more than
10LUX, the sensor would not work and the lamp stop working too. If the ambient light is less
than 10LUX (darkness), the sensor would work. Under no induction signal condition, the
sensor should stop working within 10sec±3sec.
Note: when testing in daylight, please turn LUX knob to + (SUN) position, otherwise the
sensor lamp could not work!
CONNECTION-WIRE DIAGRAM:
(See the figure)
SENSOR INFORMATION:
Wall Mounting
Height of installation: 1.8-2.5m Detection Distance: Max.16m
Ceiling Mounting
Height of installation: 2.2-4m Detection Distance: Max.10m
SOME PROBLEM AND SOLVED WAY:
The load does not work:
a. Please check if the connection of power source and load is correct.
b. Please check if the load is good.
c. Please check if the settings of working light correspond to ambient light.
The sensitivity is poor:
a. Please check if there is any hindrance in front of the detector to affect it to receive the
signals.
b. Please check if the ambient temperature is too high.
c. Please check if the induction signal source is in the detection field.
d. Please check if the installation height corresponds to the height required in the
instruction.
e. Please check if the moving orientation is correct.
The sensor cannot shut off the load automatically:
a. Please check if there is continual signal in the detection field.
b. Please check if the time delay is set to the maximum position.
c. Please check if the power corresponds to the instruction.
IMPORTER: Prima Group 2004 LTD, Bulgaria, 1784 Sofia, Mladost 1, bl. 144, Ground
Floor; Phone: [phone];