Oregon Scientific Modena FSW-301 User manual

EN
1
TABLE OF CONTENTS
About this guide ................................................... 2
Product overview ................................................. 3
Getting started ..................................................... 8
Batteries .......................................................... 8
Change settings .............................................. 8
Remote unit setup ................................................ 9
Clock .................................................................. 10
Alarm.................................................................. 12
Barometer .......................................................... 13
Weather forecast................................................ 14
Temperature & humidity ..................................... 15
Backlight ............................................................ 18
Reset system ..................................................... 18
Safety and care .................................................. 18
Warnings ............................................................ 18
Troubleshooting ................................................. 20
Specifications ..................................................... 21
Additional resources .......................................... 23

2
EN
ABOUT THIS GUIDE
Congratulations on your selection of the Oregon
Scientific Modena Wireless Weather Station
(FSW-301). This powerful device bundles weather
forecasting, barometric pressure monitoring, indoor
and wireless outdoor temperature and humidity
measurement,timekeeping, and alarmfeaturesinto
a single tool you can use from the convenience of
your home.
Keep this manual handy as you use your new
product. It contains practical step-by-step
instructions, as well as technical specifications and
warnings you should know.
In this box, you will find:
· Main unit
· Remote sensor
· Batteries

EN
3
PRODUCT OVERVIEW
TOP VIEW
DESCRIPTIONS
1. Memory – view memory ( 

15)
2. Channel – switch remote unit (

9, 15)
3. Altitude (

13)
4. Snooze / Light (

13, 18)
5. Clock (

10)
6. Alarm (

12)
7. UP / DOWN – increase / decrease setting
or activate / deactivate auto-synchronization
(

8, 11)
1 2 3 4 5 6 7

4
EN
LEFT LCD DISPLAY DESCRIPTIONS
1. Low battery icon (

8)
2. Road conditions (

14)
3. Weather forecast (

14)
4. RF signal reception (

10)
5. Clock / Calendar (

10)
6. Alarm Status / Type (

12)
1
2
3
4
5
6

EN
5
RIGHT LCD DISPLAY DESCRIPTIONS
1. Remote unit signal reception (

9, 15)
2. Temperature (

15)
3. Temp / Humidity trends (

17)
4. Remote unit low battery icon (

8)
5. Humidity / Comfort level (

17)
6. Barometer (

13)
%RH
M
1
2
3
4
5
6

6
EN
BACK VIEW DESCRIPTIONS
1. °C/°F switch (

9, 16)
2. Radio format switch (

10)
3. Barometer unit switch (

13)
4. Reset button (

10, 18)
5. Battery compartment (

8)
5 1 2 3 4

EN
7
REMOTE UNIT DESCRIPTIONS
1. Temperature (15)
2. Humidity and comfort level (17)
3. Channel number (9, 15)
4. LED indicator (9, 15)
5. °C/°F switch (9, 16)
6. Reset button (18)
7. Channel switch (9, 15)
8. Batteries (8)
9. Battery compartment (8)
1
2
3
4
5
6
7
8
9

8
EN
GETTING STARTED
BATTERIES
Batteries for the remote and main units are supplied
with this product. Replace them whenever the low
batterysignal ( )displays. Remove the battery lid
on the bottom of the main unit. Use a small Phillips
screwdriver to remove the remote unit compartment
lid. Be sure to match the correct polarity, as shown
in the battery compartment. After you change the
batteries,press theRESET button with the point ofa
blunt object (such as a ball point pen).
Insertthe batteries in the remoteunit before
you set up the main unit. Do not use rechargeable
batteries.
CHANGE SETTINGS
Press and hold CLOCK or ALARM for 2 seconds to
enter setting mode. Then, press UP or DOWN
to change each setting. Press and hold to enter fast-
setting mode. Press CLOCK or ALARM to switch
between settings.
NOTE

EN
9
REMOTE UNIT SET UP
Up to 3 remote units can be used with this product to
monitor outdoor temperature and humidity. The
measurement unit (°C or °F) and channel number
(1, 2, or 3) switches are located in the battery
compartment, and should be set prior to installation.
Additional remote units sold separately. If
you are using more than one remote unit, be sure
to select a different channel number for each unit.
INSTALLATION
Mount the remote unit on a flat surface using the
recess holes on the back of the unit.
For best results:
·Insertthebatteriesandselectthemeasurement
unit and channel numberfirst.
·Place the unit out of direct sunlight and
moisture.
·Do not place the remote unit more than 20-30
meters (60 – 90 feet) from the main (indoor)
unit.
NOTE

10
EN
CLOCK
This product can automatically synchronize the date
and time with official time-keeping organizations in
Frankfurt(Germany)andRugby(England).Whenthe
unit is within 1500 km (932 miles) of a RF signal, the
reception icon will blink during reception.
SET RADIO SIGNAL FORMAT
The RADIO SIGNAL FORMAT switch is located in
the battery compartment. Select EU (DCF) or UK
(MSF). Then, press RESET to reset the unit.
Reception takes 2 – 10 minutes to complete. Once
complete, the icon will stop blinking.
·Position the unit so that it faces the main
(indoor) unit. Minimize obstructions such as
doors, walls, and furniture.
You may need to experiment with various locations
to get the best reception.