Original BTC Oxford Double User manual

Oxford Double Table & Floor Light
Instruction Manual
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
Table Light
US-FT620
Floor Light
US-FF630
Safety Instructions
Cleaning and Maintenance
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury.
Please retain for future reference. When fitting is in operation, some parts will become hot; take care when
using/handling.
- Ensure the lamp type and max wattage is followed- do not exceed. Take care not to overtighten
lamp.
- Do not touch the lamp (bulb) or lamp holder while in operation, as both become very hot.
- Turn off and unplug fitting, leaving lamp to cool before changing lamp. Dispose of old lamps
carefully.
- Adjust light fitting only when power to the fitting is off and has been left to cool.
- Never leave a fitting without a lamp in position.
- Keep light fitting away from combustible materials such as soft furnishings.
- Ensure children do not play with the light fitting.
- Ensure the light is positioned on a solid, level and non-slip surface and make sure the position of
the cable does not pose a trip hazard.
- If the electrical flex or electrical components become damaged at any point, the fitting must be
unplugged from the power supply immediately and not operated until the damaged parts are
fixed/replaced.
- For use in a dry, indoor environment only. Ensure the fitting does not come into contact with any
liquids.
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Bone china can be
cleaned by hand, using a soft damp cloth with a diluted mild detergent (non abrasive) if necessary. Switch off
power to the fitting before cleaning.
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and
contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
v1.3-05.19
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE
ENG WARNING – RISK OF FIRE AND ELECTRIC SHOCK.
SUITABLE FOR DRY LOCATIONS ONLY
FR ATTENTION – RISQUE D’INCENDIE, RISQUE DE CHOC.
POUR EMPLACEMENTS SECS SEULEMENT
US-FT554 / FT555

Oxford Double Table & Floor Light
US-FT620/BR - Oxford Double table light
US-FF630/BR - Oxford Double floor light
120V ac 60Hz IP20
Assembly
A
A C
G
H
B
D
E
F
C
D
B
G
E
F
F
Hensure metal
brackets are aligned
Fig 1
GU10 PAR16
LAMP GUIDANCE
TYPE* WATTAGE** BASE SHAPE


HALOGEN
LED
n/a
10W
* Use LED lamps only. Warm white (2700k) recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
- With the bulb installed, place the first 47mm washer (F) on top of the shoulders shade carrier at the top of the lamp base.
- Place the cyclindrical shade on top of this.
- Place the second large washer (F) on top of the shade hole, and then place the spacer (E) on top of this, aligning the 3 legs
with the legs of the shade holder underneath (see fig 1.)
- Put the small 20mm washer (D) over the threaded tube, onto the spacer.
- Place the conical shade (C) onto this, place the brass disc (B) on top (logo up) and fix in place with the finial (A).
Do not overtighten
Contents
Contents
A
B
C
D
E
F
G
H
Finial
Disc
Conical shade
20mm Rubber washer
Spacer
47mm washer (x2)
Cylindrical shade
Lamp base