Original BTC Portable Pleat FW545N User manual

Portable Pleat
Instruction Manual
Wall Light
Safety & Installation Instructions
Other Important Information
Switch off at mains before changing lamp(s). Never fit a lamp of greater wattage than recommended. Ensure children do not
play with the light fitting. If the fitting is to be positioned in an area which can be accessed by young children we recommend
installing the light with a suitable cable clip to prevent the flex from becoming a choking hazard. These are available at good
hardware stores. Dispose of old lamps carefully. Never leave a fitting without a lamp in position (or someone can accidently
touch the contacts). Adjust fitting only when power to the fitting is off and has been left to cool. If the electrical flex or
electrical components become damaged at any point, power to the fitting should be disconnected immediately and not operated
until the damaged parts are fixed/replaced. For use in a dry, indoor environment only. Ensure the fitting does not come into
contact with any liquids.
Cleaning and Maintenance
Metal finishes should only be cleaned with a soft, dry cloth. Do not use polishes or abrasives. Bone china can be cleaned by
hand, using a soft damp cloth with a diluted mild detergent (nonabrasive) if necessary. Switch off power to the fitting before
cleaning.
MADE IN BRITAIN
ORIGINALBTC.COM
[phone]
UNIT 21 / 22 AVENUE ONE, STATION LANE, WITNEY, OX28 4XZ, ENGLAND
Established in 1990, Original BTC manufactures relaxed, familiar lighting for traditional and contemporary homes.
All products are hand-assembled in Oxford from high quality components, produced in the UK.
v1.1-04.19
These instructions are provided for your safety in order to prevent the risk of Fire, Electric shock or Injury. It is vitally
important that they are read in their entirety before installing your fitting. Please retain for future reference.
1. If you are in any doubt consult a qualified electrician as to the installation of the fitting. Install in accordance with current
IEE wiring regulations. It is recommended that this fitting is installed by a qualified electrician.
2. Carefully identify where the supply cable is (and check there are no other cables in the area) to avoid damage to concealed
wiring during installation.
3. Position the light where desired ensuring that there is suitable support adjacent to where you will connect to the house
supply and mark position of fixing holes, before drilling appropriate holes as below.
4. a. Brick or masonry: Drill holes into which the wall plugs tightly fit, then insert wall plugs.
b. Wood: No hole necessary (unless small pilot hole required), screws can be screwed directly into the timber.
c. Plaster/Cavity: Special cavity wall fittings are required, rather than provided fixings. These are widely available from
good hardware or DIY store and should come with their own instructions that must be followed. It may be easier to
relocate the fitting so that you screw directly into a timber joist or beam.
5. Fit the correct type and wattage of lamp (or less). Be careful not to overtighten the lamp.
6. Switch on at the fuse-board. Your light fitting is now ready for use.

Portable Pleat Wall Light
PLEASE READ THE INSTRUCTIONS ON THE REVERSE BEFORE YOU BEGIN INSTALLING YOUR LIGHT
Refer to diagrams on the opposite page.
- Unscrew the two-part metal button fixing in the supplied fixing pack.
- Follow steps 2 to 4 on the back page. Ensure there is a plug socket located nearby.
- Screw the “Bracket” (D) to the wall.
- Attach the “Button” (A) to the bracket, screwing through the hole in the shade (B).
- Ensure that the shade hangs securely and the bracket is fixed securely to the wall.
- Insert the correct type of lamp, before plugging into a nearby socket.
- Your light is now ready for use.
230V ac 50Hz Contents
Installation Diagram
Hanging Instructions
IP20
FW545N Portable Medium Pleat Wall Light, Sand & Taupe Braided Cable
FW546N Portable Large Pleat Wall Light, Sand & Taupe Braided Cable
The Portable Pleat is our most flexible wall light. A pleated bone china shade is held to the wall by
a polished chromed round wall fixing. Available in two shade sizes, the light has 2.5m of cotton
braided cable with an inline switch and plug. This allows the light to be positioned anywhere,
without needing hard wiring.
This product is made from Fine Bone China; take care when handling this product during
installation.
- Cross head screwdriver
- Drill (if holes are required)
Contents
Tools Required
1
2
3
4
Shade
Rawl plug
Fixing screw
2 Part fixing button
1
E27 GLS BALL
LAMP GUIDANCE - FW545N Portable Medium Pleat
TYPE* WATTAGE** BASE SHAPE




INCANDESCENT
CFL
ECO-HALOGEN
LED
40W MAX
11W
n/a
7W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
E27 GLS BALL
LAMP GUIDANCE - FW546N Portable Large Pleat
TYPE* WATTAGE** BASE SHAPE




INCANDESCENT
CFL
ECO-HALOGEN
LED
60W MAX
15W
42W
12W
* Warm white (2700k) low energy lamps recommended.
** Wattage value provided as a guide to suitable lamps. Lower wattage than stated may be used.
Fig.1 Fig.2
B
A
234
CDE
A
B
C
Button
Shade
Screw
D
E
Bracket
Rawl plug
Key