ORION Images 21REDPH User manual

Installation and User's Guide
PREMIUM WIDE ASPECT RATIO LED SERIES
USER
MANUAL
<All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein>

R00 2
[ USER MANUAL ]
LCD Display Monitors
Three-Year Limited
Warranty
Orion Images Corporation (“OIC”) warrants to the first purchaser that its LCD Display monitors are free from defects in materials
and workmanship under normal use. The warranty is three years beginning on the date of invoice, as further described in the
following text.
During the first 30 days of the warranty period, OIC will exchange the product without charge to the purchaser. After 30 days, OIC
will offer the repair of devices only up to the conclusion of the three-year warranty period. OIC may, at OIC’s sole option, use
rebuilt, recondition, new parts or components when repairing any device.
To request warranty service, you must call OIC’s Customer Service at [phone], ext. 121 within the warranty period.
If warranty service is required, OIC will issue a Return Material Authorization Number. You must ship the products back to OIC
in their original or equivalent packaging, prepay shipping charges and insure the shipment or accept the risk of loss of damage
during shipment. OIC will ship the repaired or replacement products to you freight prepaid if you use an address in the
continental U.S. or Canada, where applicable. All other locations will require shipping costs to be covered by the purchaser.
This warranty does not cover:
1. Damage due to shipping and external causes, including accident, abuse, misuse, problems with electrical power, servicing not
authorized by OIC, usage not in accordance with product instructions, failure to perform required prevent maintenance,
problems caused by use of parts and components not supplied by OIC, act of God, tampering or normal wear and tear;
2. Products on which the serial number has been altered, defaced, or removed;
3. Products purchased outside the United States and Canada;
4. Products whose back covers have been opened, replaced, modified, or show signs of tampering both physically or electrically.
OIC MAKES NO EXPRESS WARRANTIES BEYOND THOSE STATED IN THIS WARRANTY STATEMENT. OIC DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. SOME STATES (OR JURISDICTIONS) DO NOT ALLOW LIMITATIONS ON IMPLIED
WARRANTIES, SO THIS LIMITATION MAY NOT APPLY TO YOU.
OIC’S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET
FORTH IN THIS WARRANTY STATEMENT. THESE WARRANTIES GIVE YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VERY FROM STATE TO STATE (OR JURISDICTION TO JURISDICTION).
OIC DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES SET FORTH IN THIS WARRANTY STATEMENT OR LIABLITY FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION ANY LIABILITY FOR PRODUCTS NOT BEING
AVAILABLE FOR USE.
SOME STATES (OR JURISDICTION) DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE PROCESSDING EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU.
These provisions apply to OIC’s limited three-year warranty only. For provisions of any service contract covering your systems,
refer to the separate service contract that you will receive.

R00 3
[ USER MANUAL ]
<TABLE OF CONTENTS>
1 SAFETY INSTRUCTION 4
2 FCC RF INTERFERENCE STATEMENT 8
3 INSTALLATION 9
4 OSD MENU SETTING 16
5 FEATURE 22
6 VGA / HDMI / DP / HDA Mode Table 24
7 TROUBLESHOOTING 25

R00 4
[ USER MANUAL ]
1. SAFETY INSTRUCTION
•Follow this safety instruction to use the monitor properly and prevent the damage.
•Keep this user’s guide book for later use.
* This safety instruction has “Warning” & “Caution” as below
Warning - If the user does not follow this instruction,
it may cause the serious damage to the user.
Caution - If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.
Warning
Never remove the back cover and touch
the inside of the monitor.
If you need a service, please contact the
service center.
Keep away the monitor from the
direct sunlight and a heating appliance.
Never put objects of any kind into this
product as they may result in a risk of fire
or electric shock.
Connect the power cord to the wall
outlet tightly. If the power cord or plug are
defective and the wall outlet is not
tight, please do not use them.

R00 5
[ USER MANUAL ]
Warning
Do not install this monitor on the outside
and near water. It may cause damage to
the product, electric shock and fire.
When lightning and thundering, unplug
the monitor from the wall outlet and
never touch it.
Unplug this product from the wall outlet,
when it does not operate for a long time.
When smoking and noising from the
monitor, unplug the product from the wall
outlet and contact a service center.
For cleaning do not use liquid cleaners.
Never touch the power plug with wet-
hands.
WARNING: How to fix
Do not open this product as it contains high voltage inside.
It may create an electric shock.
If the user disassembles and remove the back cover, it does not make sure
to make up for the damage and do a service and exchange the monitor.

R00 6
[ USER MANUAL ]
Cautions
Install this monitor some distance
from the wall and do not install unless
proper ventilation is provided.
Place this product on a stable place.
If not, it may fall, causing serious
damages to the monitor and people.
The openings must not be blocked by
curtain, rug or other similar surface.
Before carrying the monitor, turn it off and
unplug the signal cables and the power
cord from the wall outlet.
When carrying this monitor, be careful
not to damage the panel and drop it
It may cause some trouble.
Take the power plug out from the wall
outlet.
Do not pull the cable. It may snap the
inner-wires and cause overheating and fire.

R00 7
[ USER MANUAL ]
Cautions
Install this monitor about 50cm far from
the eyes and an angle of 0~15 degrees
below eyes. Too close installation may
cause having weak sight.
Do not press the LCD panel with hands or
the sharpened material hardly.
For cleaning, unplug the monitor from the
wall outlet. Do net use the liquid cloth.
Use the soft cloth.
Do not use the chemical liquid for cleaning.
It may cause fading and breakage.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR WATER.
Instructions for Disposal of Electrical and Electronic Equipment in Private Households
Disposal of used Electrical and Electronic Equipment
(Applicable in the European Union and other European countries with garbage separate
disposal and collection methods)
This symbol on the product, or in the related documents in the package, indicates that this
product shall not be treated as normal household waste. Instead, it should be taken to a proper
applicable collection point or depot for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent possible negative consequences for
the environment and human health, which could otherwise be caused by inappropriate waste handling of
this product. The recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local city authority,
your household waste disposal service or the place where you purchased the product.

R00 8
[ USER MANUAL ]
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio, TV technician for help.
- Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the grantee or
manufacturer could void the users authority to operate such equipment.
DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the radio interference regulation of Canadian Department of communications.
2. FCC RF INTERFERENCE STATEMENT

R00 9
[ USER MANUAL ]
3. INSTALLATION
PARTS
User Manual
Adapter(21~32”)
LCD Monitor
Remote Controller
Power Cable
Battery
DP Cable
*Please use only the DisplayPort cable provided with Monitor.
This monitor is not compatible with other DisplayPort cables.
**Depending on the product model type, there may be variations in appearance.

R00 10
[ USER MANUAL ]
HOW TO INSTALL
1) KEY BUTTON
SHORT KEY FUNCTION
OSD Key Function
MENU Activate the menu function / Exit from the menu
SOURCE / ▼Input source menu / Source selection(move down from OSD menu)
AUTO / ▲Auto-fit screen with PC-RGB input / move up from OSD menu
◀(VOL) Decrease the level of volume and move the previous menu
(VOL)▶Increase the level of volume and select the OSD menu
Power On / Off
LED
Red : Power Off state
Green : Power On and available input signal state
Orange : When DPMS "ON" state, no input signal
▲+◀Press “▲ , ◀” Key 10 seconds simultaneously to lock /
unlock OSD Key

R00 11
[ USER MANUAL ]
2) CONNECTION
- 21, 23REDPH
① ② ③ ④ ⑤ ⑥ ⑦
①DP DP signal input
②HDA HD analog signal input
③HDMI HDMI signal input
④VGA VGA(PC RGB) signal input
⑤AUDIO(PC) Stereo audio input for VGA
⑥For FW Update
⑦DC 12V DC adapter input

R00 12
[ USER MANUAL ]
2) CONNECTION
- 27REDPH
① ② ③ ④ ⑤ ⑥ ⑦
①DP DP signal input
②HDMI HDMI signal input
③VGA VGA(PC RGB) signal input
④AUDIO(PC) Stereo audio input for VGA
⑤For FW Update
⑥DC 12V DC adapter input
⑦HDA HD analog signal input

R00 13
[ USER MANUAL ]
2) CONNECTION
- 32REDPH
①DP DP signal input
②HDA HD analog signal input
③HDMI HDMI signal input
④VGA VGA(PC RGB) signal input
⑤AUDIO(PC) Stereo audio input for VGA
⑥For FW Update
⑦DC 12V DC adapter input
① ② ③ ④ ⑤ ⑥ ⑦

R00 14
[ USER MANUAL ]
2) CONNECTION
- 43, 55REDPH
① ② ③ ④ ⑤ ⑥ ⑦
①DP DP signal input
②HDA HD analog signal input
③HDMI HDMI signal input
④VGA VGA(PC RGB) signal input
⑤AUDIO(PC) Stereo audio input for VGA
⑥For FW Update
⑦AC POWER AC100~240V input

R00 15
[ USER MANUAL ]
3) REMOTE CONTROLLER
MODE SELECT MENU
HDMI Select HDMI mode
DP Select DP mode
VGA (RGB) Select VGA mode
S.SET Select Input source
OSD CONTROL MENU
POWER Turn ON / OFF the monitor
MUTE Turn ON / OFF the sound
AUTO Auto adjust position of the screen (in VGA mode)
COLOR
TEMPERATURE Select color temperature of the screen
SCAN MODE Select the scan mode of the screen
VOL- / VOL+ Increase / Decrease the volume level
MENU / EXIT Activate and exit the OSD menu
KEY LOCK Locking the button (Prevent operation)

R00 16
[ USER MANUAL ]
4. OSD MENU SETTING
MENU STRUCTURE
When user presses the menu key, the first “PICTURE” menu is displayed. Select by "◀"
key then two types of menu functions are shown as below.
- PICTURE : Menu related to PICTURE Function
- OPTION : Other OSD Menu Status Control and Firmware Update
If press "▲, ▼" key, then select sub title in functions.
The PICTURE Menu can be selected from the following 6 modes by pressing the ▲or ▼key.
PICTURE MENU
Picture Mode Adjust setting of the picture
Color Temperature Change color according to the color temperature
Aspect Ratio Change the aspect ratio
Noise Reduction Adjust noise attenuation of input signal
Screen Adjust the PC-RGB input signal to fit the screen
Pixel shift Select auto pixel shift

R00 17
[ USER MANUAL ]
1) Picture Mode
Picture Mode can select 4 modes as Mild, Dynamic, Standard and User as shown in the figure
below. Press the "◀, ▶" key to change the mode.
Three of the four modes except for User mode are shipped with fixed values at the time of
shipment from the factory.
User mode can be set with “◀, ▶” keys by selecting each item below with “▲, ▼” key only
in the User mode.
2) Color Temperature
Color Temperature can select 4 modes as Cool, Medium, Warm and User as shown in the figure
below.
Three modes except User mode are factory shipped with factory default values, and
each color item (RED, GREEN, BLUE) is selected with the "▲, ▼" keys in the User mode only.
User settings are available.
Contrast Adjust difference in the color and brightness
Brightness Adjust the dark and light
Color Adjust for desired color intensity
Sharpness Adjust for best clarity of outline detail
Tint Adjust for natural flesh tones

R00 18
[ USER MANUAL ]
3) Aspect Ratio
Aspect Ratio allows user to select the each aspect ratio as shown in the figure below.
(However, activated list is according to the input port and the input resolution.)
4) Noise Reduction
Noise Reduction can select 5 modes as Off, Low, Middle, High, Default as shown in the figure below.
5) Screen
Screen enables to set the active area of the display when using PC-RGB input port.
Auto Adjust is an item to be set automatically, and the input signal should be operated in the
signal state where the Outline has a lot of white color.

R00 19
[ USER MANUAL ]
6) Pixel shift
Select auto pixel shift (On, Off)
The Option Menu can be selected from the following 7 modes by pressing the ▲or ▼key.
OPTION MENU
OSD Language Selectable OSD Menu Language
OSD Duration Setting Duration time of OSD Menu
Restore Factory Default
Software Update(USB)
Key Lock Locking the button(prevent operation)
DPMS When input signal is the no signal, DPMS "on" change
the power saving mode.
Cycle setup Select auto input source

R00 20
[ USER MANUAL ]
1) OSD Language
As shown in the figure below, OSD Language can be selected by "▲, ▼" key.
2) OsdDuration
OSD menu Duration can select 4 modes as 5, 10, 15Sec and Off by pressing the “▶ SELECT” key.
3) Restore Factory Default
Restore factory default can be selected by pressing the "▶SELECT" key. Select Yes or No by
the “◀, ▶" key.
4) Software Update(USB)
Software update default can be selected by pressing the "Menu" key. Select Yes or No by
the “◀, ▶" key.