OT Systems IES8222MPp9H-S-DR User manual

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES8222MPp9H-S-DR / version 1.0
Quick Installation Guide
IES8222MPp9H-S-DR
Description: L2+ Hardened Grade Managed 8-port 10/100/1000Base-TX (PoE+) + 2-port
100/1000Base-SFP Ethernet Switch
Overview: IES8222MPp9H-S-DR is a new generation, managed, industrial grade, L2+ Gigabit PoE++
(Power over Ethernet plus plus) switch that provides 8x10/100/1000Base-TX RJ45 ports
plus 2x100/1000Base-SFP ports. It provides stable and reliable Ethernet transmission
with high quality design and reliability.
Package Content
⚫Managed PoE Switch x 1
⚫DIN-Rail Clip x 1
⚫Quick Installation Guide x 1
Read Before Install
◎Keep power off during installation
◎use Antistatic Wrist Strap correctly
◎Make sure using correct power supply, voltage must match
◎Make sure enough power supply from PSU that will not overload
◎Double check the wiring ( +/- ) is correct.
◎Keep installation dry and clean.
◎Do not open the chassis

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES8222MPp9H-S-DR / version 1.0
DIN Rail Installation
DIN rail. Installation methods are as follows:
Power Input
The Industrial Switch has two redundant power inputs, PRW1 and PWR2. The Phoenix terminal
patch panel connector is located on the top panel of the switch. The front view of the patch panel is
shown below.
PoE Output
IEEE 802.3bt, per port 90W, 1/2(+), 3/6(-); 4/5(+), 7/8(-)
Setup and States
a) Connect the Ethernet port of the media converter to a PoE IP camera (PoE device) or network
device with a network cable.
b) Insert the appropriate SFP into the SFP port. Connect the fiber cable from the device (media
converter or switch) on the other end to the LC connector of the SFP.
1
2

OT Systems Ltd. | www.ot-systems.com
Quick Installation Guide
IES8222MPp9H-S-DR / version 1.0
c) After the device is powered on, the PWR indicator will all be on. If the indicators are not on,
check the power supply connection.
d) After all cables are correctly connected, the indicators will be lit as per port status LEDs.
LED
Status
Description
LED
Power Supply (PWR)
Status
Normal
ON
Power off
System Status (SYS)
OFF
Normal
ON
System does not start
SFP Port LED (LNK)
OFF
SFP port connected
ON
Data transmission enabled
Blink
SFP port disconnected
Ethernet Port (Yellow LED)
OFF
Ethernet port connected
ON
Data transmission enabled
Blink
Ethernet port disconnected
Ethernet Port (Yellow LED)
OFF
1000M
ON
10/100M
Introduction to DIP switches (If with dip)
NO
Function
Status
Description
1
LFP function
OFF
Disable
ON
Enable
2
ALS function (only for SFP)
OFF
Disable
ON
Enable
3
FX Reset
OFF
Disable
ON
Enable
4
FX Speed Set
OFF
FX 1000M
ON
FX 100M/1000M
LFP and ALS are started at the same time, LFP is valid, ALS does not work.
FX Reset: if enable, when FX link down, power will shut down, a few second and power up.
General
To ensure trouble free transportation and storage, all OT Systems products must be thoroughly
inspected, tested and properly packed before delivery. Check the product upon receipt for any
visible damage which may have been caused during shipment.
-END-