Otto HORSENS 3 DRAWER PEDESTAL OTHOR3DWE User manual

ASSEMBLY INSTRUCTIONS
HORSENS 3 DRAWER PEDESTAL
OTHOR3DWE
This design and instruction booklet is subject to copyright.
www.officeworks.com.au
1/12

Officeworks Superstores Pty Ltd. I 236-262 East Boundary Road I East Bentleigh I 3165 I AUSTRALIA
Tools Required For Assembly
Recommend 2 Adults to Assemble
Assemble Item On a Clean Flat Surface
Please check you have all hardware before assembling.
If you think you are missing any hardware please contact the store of purchase.
Please ensure you have the name of the item and hardware part required and quantity.
Please retain your receipt for proof of purchase to validate warranty. Enjoy your new purchase.
At least every 4 months, check all bolts, screws and knobs to be sure they are tight.
If parts are missing, broken, damaged or worn, stop use of the product until repairs are made,
using factory authorized parts.
Failure to follow these warnings could result in serious injury.
WARNING
.
.
.
.
Do not tighten the screws before all screws are in right place.
.Do not use this cabinet unless all bolts, screws and knobs are firmly secured.
.
.
.
.
2/12

A B C D E
F G H I J
K L M N
P
x4pcs x13pcs x8pcs x9pcs x36pcs
x6pcs x6pcs x2pcs x14pcs x16pcs
x16pcs x1pc
x2pcs
x2pcs
x4pcs
x4pcs
O
∅15x11mm M6x35mm ∅8x30mm ∅15x9mm ∅3.5x12mm
350mm 350mm ∅7x364mm ∅4x30mm
∅4x14mm
∅6x30mm ∅4x35mm
Q
∅4x12mm
x4pcs
1 2 3 4 5
6 7 8 9 10
11 12 13 14 15
x1pc x1pc x1pc x1pc x1pc
x1pc x1pc x1pc x1pc x1pc
x3pcsx2pcsx2pcsx2pcs x2pcs
PARTS LIST
HARDWARE LIST
3/12

Step 1
Step 2
1
B
B
B
B
B
E
E
E
E
E
E
E
E
E
E
E
E
F
F
FF
F
F
23
E
E
EE
E
E
1:
2:
3:
E
E
E
F
E F
x18pcs x6pcs
B
x4pcs
4/12
F
FG
G

Step 3
Step 4
1
2
3A
AA
A
C
C
C
C
C
3
2
5
Q
Q
Q
Q
Q
C
C
C
A C
x4pcs x4pcs
C Q
x4pcs x4pcs
5/12

Step 5
Step 6
J
J
4
5
M
M
M
M
L
L
K
K
L
K
M
M
XX
YY
XX=YY=90°
K L
x2pcs
M
x2pcs x16pcs
J
x16pcs
6/12
caster with lock
caster without lock
4
J
Note: Partially hammer the nails 2/3
into back panel at this step for easy
removal. After the drawers are fully
aligned and travel smoothly, fully
hammer nails to inside back panel.

Step 7
Step 8
6
B
B
B
x2
E
E
E
E
E
E
E
GG
x2 x2
79
EG
x12pcs x4pcs
B
x4pcs
7/12

Step 9
Step 10
D
D
P
P
I
I
7
9
8
10
x2
x2
I
D P
x4pcsx4pcs
D
I
x8pcs
8/12

Step 11
Step 12
B
B
B
B
B
B
E
E
E
E
E
E
E
GG14
12
11 B
EG
x6pcs x2pcs
B
x5pcs
9/12

Step 13
Step 14
DD
D
D
14
12
15
10
D
D
11
D
x5pcs
10/12

Step 15
Step 16
II
II
II
13
H
H
I
15
O
N
N
O
I
x6pcs
H
x2pcs
N O
x1pc x4pcs
11/12

Step 17
6
Step 18
6
11
12/12
MAXIMUM WEIGHT CAPACITY
CAUTION: This product is intened to hold the Maximun Weight indicated. Exceeding the
Maximum Weight will result in instability and may cause possible injury.
Thank you for purchasing our product! Please retain your receipt to validate warranty
lf you’d like to know more about Officeworks’ furniture products, please visit our website.www.officeworks.com.au
NOTE: Stationery drawer 5kg
Filing drawer 15kg
If the drawer’s two side gaps were not aligned,
please pull out the back panel nails and adjust
the cabinet angles to ensure the frame angles
are square. After the drawers are fully aligned
and travel smoothly, fully hammer nails to inside
back panel. lock
release
Ball bearing
Ball bearing
Front
Place the assembled drawers into the frame by aligning the slide runners of the
drawers with the runners on the unit. If the drawer does not slide in smoothly,
remove the drawer to ensure the alignment on both sides are correct. Push the
drawers all the way into the unit until it stops.
F
F
G
G