Outback TPA101-6 Quick reference guide

ASSEMBLY & OPERATING INSTRUCTIONS
OUTBACK COMMERCIAL
Model: TPA101-6

Chapter 1: Safety Information
Chapter 2: Package Contents List
Chapter 2: Hardware Contents List
Chapter 3: Assembly
Chapter 4: Leak Testing
Chapter 5: Important Information
Chapter 6: Gas, Regulator and Hose
Chapter 7: Installation
Chapter 8: Operation
Chapter 9: Care and Maintenance
Chapter 10: Technical Specifications
Chapter 11: Troubleshooting
Chapter 12: Parts Diagram
Chapter 13: Parts List
Page Table of Contents
3
4
4
5
8
9
10
11
12
15
17
17
18
19
2

3
Safety Information
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
For outdoor use only. Not for commercial use.
Read instructions before using the appliance. Failure to follow
instructions could result in death, serious bodily injury, and/or property
loss.
Warning: accessible parts may be very hot. Keep young children and
pets away.
Do not move the appliance during use.
Any modification of the appliance, misuse, or failure to follow the
instructions may be dangerous and will invalidate your warranty. This
does not affect your statutory rights.
For Flare-up control please refer to the ‘OPERATION’ section of this manual.
Retain these instructions for future reference.
Turn off the gas supply at the gas bottle after use.
Leak test annually, and whenever the gas bottle is removed or replaced.
Check that the hose connections are tight and leak test each
time you reconnect the gas bottle.
FOR YOUR SAFETY
FOR YOUR SAFETY
If you smell gas:
Shut off gas to the appliance.
Extinguish any open flame.
Open barbecue lid or hood.
If odour continues, discontinue use and contact your local dealer.
WARNING
Do not store or use petrol or other flammable vapours or liquids in the
vicinity of this or any other appliance.
A gas bottle not connected for use must not be stored in the vicinity of
this or any other appliance.

A. Firebox --------1pc. B. Cart Assembly-----1pc. C. Cooking Griddle--1pc.
D. Wheel Cap------2pcs E. Wheel----2pcs F. Wheel Axle- ------1pc.
G. Side Shelf Support-----2pcs. H. Swivel Caster with Brake---1pc I. Swivel Caster---------1pc.
J. Grease Cup Holder----- 2pcs. K. Grease Cup----------2pcs. L. Flame Tamer----------5pcs.
M. Gas Grill Cooking Grid---
3pcs N. Rubber Stopper--------2pcs Carefully unpack the packing
box and remove all contents
before commencing
assembly. Make sure that
you obtain all correct
package contents.
AA BB CC
Item Description Quantity
AA 1/4-in. x 15-mm Round Head Screw 20
BB Allen Key 1
CC M12. Nut 2
DD 1/4-in. x 12-mm Round Head Screw 2
EE 1/4-in Flat washer 2
FF 1/4-in Lock washer 8
DD
FFEE
4
Package Contents List
Hardware Contents List

UNPACKING
CAUTION: Obtain the aid of an assistant when
handling large or heavy grill components.
1. Once the top of shipping box is open, obtain
the aid of an assistant and lift the cardboard
sleeve up over Firebox and components.
2. Use sleeve as a work surface to protect floor
and grill parts from scratches.
3. Remove all packing materials from around grill
exterior.
4. Open both Firebox lids and remove packing
materials and components inside each Firebox
chamber.
Assembly
Latch
5. Open the four latches as below.
6. With the help of an assistant, lift the firebox (A)
away from the cart assembly (B) separating the
two pieces. Remark: the lighting stick is
preassembled on the cart leg
7. Attach the wheel axle (F) through the cart
legs, as shown below picture, then attach the
two wheels (E) with two M12 nuts (CC), and
attach two wheel caps (D) with two 1/4-in. x 12-
mm round head screws (DD) and two1/4-in flat
washers (EE) at the end of the wheel axle (F).
8. Attach the swivel casters (I) and swivel caster
with brake (H) using eight 1/4" x15 mm round head
screws (AA) with 1/4-in lock washer (FF), four for
each caster. Ensure the swivel caster with brake
（H) is at the front of the cart frame. Tighten the
eight screws.
H
I
AA
FF
5
F
CC
D
DD
CC
D
DD
E
EE

9. Attach the right side shelf support (G) with six 1/4‘’ x
15mm round head screws (AA), repeat the same step
to attach left side shelf support. Ensure all screws are
secured tightly. Make sure the side shelf buffers are
pointing upward when attaching the side shelf support.
10. With the help of an assistant, align the grill
body to the cart as shown below, then lock the four
latches, securing the firebox to the cart.
11. Open the latch between side shelf, left &
right.
12. Unfold side shelf, left & right and wind shield
and place the tabs of the side wind shields into
the small openings securing the windshield.
Remark: The lighting stick is preassembled on
the cart leg
6
Assembly
G
AA
AA
G

13. Place the flame tamer (L) and gas grill cooking
grids (M) in the firebox and secure them. Then place
the cooking griddle (C) as shown below.
NOTE: Rubber stoppers are provided and
should only be used for transportation of the
unit. Place rubber stopper into the grease
drainage hole when you have finished cooking
and the grill has cooled. This will help to avoid
grease dripping from the firebox during
transport.
WARNING
Please remove the rubber stopper from the
grease hole before using.
14. Put the grease cups (K) into grease cup holder
(J). Then hang the grease cup holder on the bottom
of the firebox, as shown below.
15. To install the battery ( not supplied), turn the
ignition button cap counterclockwise and remove it.
Insert the battery into the housing with the positive (+)
terminal facing outward. Screw the ignition button cap
back into place.
7
Assembly
L
M
C
K
J

13. Place the flame tamer (L) and gas grill cooking
grids (M) in the firebox and secure them. Then place
the cooking griddle (C) as shown below.
NOTE: Rubber stoppers are provided and
should only be used for transportation of the
unit. Place rubber stopper into the grease
drainage hole when you have finished cooking
and the grill has cooled. This will help to avoid
grease dripping from the firebox during
transport.
WARNING
Please remove the rubber stopper from the
grease hole before using.
14. Put the grease cups (K) into grease cup holder
(J). Then hang the grease cup holder on the bottom
of the firebox, as shown below.
15. To install the battery ( not supplied), turn the
ignition button cap counterclockwise and remove it.
Insert the battery into the housing with the positive (+)
terminal facing outward. Screw the ignition button cap
back into place.
7
Assembly
L
M
C
K
J

Important Information
Please read these instructions carefully before assembly and use of your barbecue.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Retain these instructions for future reference.
This product is for outdoors use only. Do not use indoors.
Remove plastic wrap from any part before lighting.
Do not use within 1m of any flammable structure or surface. Do not use under any
combustible surface.
Open the barbecue lid before lighting.
Once lit, do not move the barbecue until it has completely cooled, after use.
This barbecue must not be left unattended when lit.
The lid handle can become very hot. Grip only the centre of the handle. Always use
oven gloves when cooking or carrying out any adjustments to the barbecue.
Use purpose designed barbecue tools with long, heat resistant handles.
Use caution when opening the lid, as hot steam inside is released upon opening.
Parts of this barbecue become very hot – care must be taken, especially when
children, elderly people, and animals are present.
Never cover a barbecue until it has completely cooled.
Use this barbecue only on a stable, flat surface.
Do not store flammable materials near this barbecue.
Do not use aerosols near this barbecue.
Failure to follow the manual’s instructions could result in serious injury or damage.
Modification of the barbecue may be dangerous, is not permitted and will nullify any
warranty. regarding these instructions, contact your local dealer.
Turn off the gas supply at the gas bottle after use.
Do not use the barbecue or store gas bottles below ground level. LP gas is heavier
than air so if a leak occurs the gas will collect at a low level and could ignite in the
presence of a flame or spark.
For use with LPG bottled gas only. A suitable regulator must be used for butane,
propane or mixes.
LP gas bottles should never be placed directly underneath the barbecue.
LP gas bottles should never be stored or used laid on their side, in the horizontal
position. A leak would be very serious and liquid could enter the gas line with serious result.
Never store gas bottles indoors.
Before you use your barbecue, perform a leak test. This is the only safe and sure way
to detect any gas leaking from joints and connections of the barbecue after assembly.
Leak test annually, and whenever the gas bottle is removed or replaced.
9

Gas, Regulator and Hose
This barbecue can use either propane or butane or propane / butane mixed LPG (liquid
petroleum gas) bottled gas. Propane bottles, will supply gas all year round, even on
cold winter days. Butane bottles will supply sufficient gas in summer, but it may affect
the performance of the barbecue and restrict the heat output available from the burners,
particularly once the gas temperature starts to fall below +10°C. A spanner may be
required to change gas bottles. Check that you have the correct gas bottle and regulator
for your barbecue.
Do not stand the bottle on the cart base.
YOU MUST HAVE THE PROPER REGULATOR AND BOTTLE IN ORDER FOR THE
BARBECUE TO OPERATE SAFELY AND EFFICIENTLY. USE OF AN INCORRECT OR
FAULTY REGULATOR IS DANGEROUS AND WILL INVALIDATE ANY WARRANTY.
Please consult your local gas dealer for the most suitable gas bottles and regulators.
10
•
•
•
The hose should hang freely with no bends, twisting, tension, folds, or kinks that
could obstruct free flow of gas. Always inspect the hose for cuts, cracks, or excessive
wear before use.
Apart from the connection point, no part of the hose should touch any hot barbecue
parts. If the hose shows any sign of damage it must be replaced with a hose suitable
for use with LP gas which meets the national standards for the country of use.
The length of hose should not exceed 1.5 metres.