Outland Living 742 User manual

FMI BRANDS INC. 101 – 3570 194 Street, Surrey, BC, Canada V3Z 1A5
USA, Canada Toll Free: 1-888-514-1663 | Tel: [phone]
Email: [e-mail] | Hours of Operation 8:30 AM - 4:00 PM (Pacific Time)
D.742.000.V0
DUNBAR Tank Cover
Model number 742
® Registered trademark of FMI Brands Inc.
OWNER’S MANUAL
DUNBAR
TANK COVER
Propane cylinder,
pressure regulator &
gas hose assembly
not included.

Owner & Safety Manual
D.742.000.V0
OUTLAND LIVING®- DUNBAR TANK COVER - OWNER & SAFETY MANUAL
En-1
NOTE TO INSTALLER:
Leave this guide with the consumer.
NOTE TO CONSUMER:
IMPORTANT. Retain this manual for
future reference. Read carefully.
WARNING:
Improper installation, adjustment,
alteration, service or maintenance can
cause injury or property damage.
Read the installation, operating and
maintenance instructions thoroughly
before installing or servicing this
equipment.
SUPPLIED PARTS & HARDWARE LIST:
PART # DESCRIPTION PICTURE
1 FRONT PANEL (x1)
2 REAR PANEL WITH CUT-
OUT (x1)
CAUTION:
Watch for sharp edges.
Wear protective gloves if necessary.
DUNBAR Tank Cover
Model number 742

En-2
1-888-514-1663 | WWW.OUTLANDLIVING.COM
SUPPLIED PARTS & HARDWARE LIST:
PART # DESCRIPTION PICTURE
3 SIDE PANEL WITH
HANDLE X2
4H-FRAME LP CLYLINDER
SUPPORT (x1)
5LID TRAY (x1)
6U-CLIPS (X12)
7M4x10 SCREWS (x16) + 1
Extra
8RUBBER FEET (x8)
REQUIRED TOOLS (Not Supplied): Philips (cross) screw driver (PH2)

Owner & Safety Manual
D.742.000.V0
OUTLAND LIVING®- DUNBAR TANK COVER - OWNER & SAFETY MANUAL
En-3
SECTION 1: ASSEMBLY
STEP 1
Unpack the contents. Check the Parts List.
a) Prepare a flat, non-marking surface for
assembly.
b) Unpack all parts.
c) Collect the U-Clips and Screws.
STEP 2
Install the Side Panels to the Front Panel.
a) Place the Front Panel (part 1) face down on
a flat, non-marking surface.
b) Align the holes on the Side Panel (part 3)
with the holes on the Front Panel.
c) Slide the U-Clip (part 6) over the holes.
d) Check the panel alignment is flush on the
sides and the ends.
e) Fasten firmly with the M4 screws.
f) Repeat with both side panels.
Note logo position:
bottom right corner
ALIGN
HOLES
SLIDE
U-CLIP
OVER
HOLES
FASTEN
FIRMLY

En-4
1-888-514-1663 | WWW.OUTLANDLIVING.COM
ASSEMBLY TIP
For the best look, ensure the panel edges are
square and aligned on the sides and the ends.
If they seem misaligned, loosen the screws a
bit, adjust the panel alignment and retighten
the screws.
IMPORTANT: Ensure
the front panel and side
panel holes for rubber
feet are on the same side.
SECTION 1: ASSEMBLY (continued)
STEP 3
Install the H-Frame Propane Cylinder Support.
a) Slide the H-Frame ends down through the
slots in the Side Panels.
b) Align the holes.
c) Fasten with the M4 Screws.
NOTE: The H-Frame ends sit behind the side
panel flanges. The threaded holes on the
H-Frame should be behind the holes in the
Side Panel flanges.

Owner & Safety Manual
D.742.000.V0
OUTLAND LIVING®- DUNBAR TANK COVER - OWNER & SAFETY MANUAL
En-5
SECTION 1: ASSEMBLY (continued)
STEP 4
Attach Rear Panel to the Side Panels.
a) Place the Rear Panel (part 2) face down on a flat, non-marking surface.
b) Align the holes on the side panels with the holes on the rear panel.
c) Slide the U-Clip (part 6) over the holes.
d) Confirm the bottom feet holes are on the same side as the others.
e) Check the panel alignment is flush on the sides and the ends.
f) Fasten firmly with the M4 screws.

En-6
1-888-514-1663 | WWW.OUTLANDLIVING.COM
SECTION 1: ASSEMBLY (continued)
STEP 5
Install the Rubber Feet.
a) Turn the assembly upside down.
b) Push-fit the (8x) Rubber Feet into the holes.
STEP 6
Turn the assembly upright, with rubber feet on
the ground.

Owner & Safety Manual
D.742.000.V0
OUTLAND LIVING®- DUNBAR TANK COVER - OWNER & SAFETY MANUAL
En-7
SECTION 1: ASSEMBLY (continued)
STEP 7
Place full propane (LP) cylinder in the base ring of the H-Frame. *
* Propane cylinder, pressure regulator and gas hose assembly not included.

En-8
1-888-514-1663 | WWW.OUTLANDLIVING.COM
SECTION 1: ASSEMBLY (continued)
STEP 8
The gas hose should go through the rear hole.
STEP 9
Place the Lid Tray (part 5) on the top of the
assembly.
Assembly
complete!
IMPORTANT:
Ensure all screws are fastened tightly. If the
screws are loose, the frame will be loose.

Owner & Safety Manual
D.742.000.V0
OUTLAND LIVING®- DUNBAR TANK COVER - OWNER & SAFETY MANUAL
En-9
TOP
FRONTSIDE
[15.7 in]
400.0 mm
[15.7 in]
400.0 mm
[19.9 in]
504.3 mm
SECTION 2: PRODUCT DIMENSIONS
APPROXIMATE DIMENSIONS
Frame Dimensions (Approx.):
HEIGHT: 504 mm / 20 in
WIDTH: 400 mm / 15.7 in
DEPTH: 400 mm / 15.7 in
The tank cover is designed to accommodate
a standard size 20lb propane (LP) cylinder
with dimensions approximately
12” Diameter x <=18” H

En-10
1-888-514-1663 | WWW.OUTLANDLIVING.COM
SECTION 3: MAINTENANCE
MOVING THE TANK COVER
The tank cover has two handles, one on each side to enable transport.
ACCESSING THE PROPANE CYLINDER
Lift the lid to access the compartment to turn on or off the propane (LP) cylinder valve.
CLEANING
Should any part of this appliance become soiled or dirty, wipe down with a damp wet cloth.
IMPORTANT
Do not use petroleum based, flammable or corrosive cleaning products on or near this unit.
ATTENTION:
Always leak test the propane cylinder connection.
SECTION 4: WARNINGS
Do not leave this appliance in the rain.
This appliance is NOT a toy.
Do not climb on the appliance, or serious injury may occur.
ATTENTION:
Children should be supervised at all times when using this unit, without exception.

Owner & Safety Manual
D.742.000.V0
OUTLAND LIVING®- DUNBAR TANK COVER - OWNER & SAFETY MANUAL
En-11
1 YEAR LIMITED WARRANTY
Customers in Canada and USA
All components are warranted by the manufacturer for a period of 1 year after date of
purchase by the original owner against defects in materials and workmanship under
normal use. This warranty does NOT cover normal wear and weathering, assembly and/
or maintenance OR use in a commercial application. At FMI Brands’ sole discretion,
products under warranty will be repaired and/or replaced at no charge to the customer.
Any returns sent back to FMI Brands must be sent via prepaid freight and in the original
retail packaging.
Please register your OUTLAND Living product for proof of purchase and warranty at
https://outlandliving.com/register-products/
For more warranty information and details please contact FMI Brands Inc. at
[e-mail]
STOP:
Do not return this product to the store.
If you need help or parts, call the OUTLAND Hotline: [phone]
Get help for:
• Missing/damaged parts • Assembly • Troubleshooting
• Warranty Assistance • Product Information
FOR REPLACEMENT PARTS AND ACCESSORIES
PLEASE VISIT WWW.OUTLANDLIVING.COM
The owner’s manual is available as a free download from www.outlandliving.com
Should you have any questions or comments regarding this product, please do not hesitate to
contact FMI Brands Inc. at [phone] or E-Mail to [e-mail].