Ovela OVBAILY6CBA User manual

BAILY CHEST OF 6
DRAWERS
BLACK
OVBAILY6CBA

2
Safety & Warnings
3
Components
5
Assembly
7
Notes
27

3
• Read all instructions carefully before assembly. Retain this user guide for future
reference.
• Lay all components out on a clean floor and ensure all parts are included. If any pieces
are missing, check all packaging thoroughly, then contact help.Kogan.com for
assistance.
• Carefully identify each component, especially those that are similar. The most common
mistake is getting things back to front.
• Separate and identify each component from the hardware pack and rest each one in its
proper location before fastening.
• DO NOT fully tighten screws (leave slightly loose). When the item is fully assembled
tighten the screws - but do not over tighten.
• If glue is required DO NOT set until you are certain that the parts belong together.
Drawer Slide Assemblies
Important: Please read before assembling
The user guide enclosed refers to multiple sets of metal Slide Runners and Slide Tracks
(pictured above separately).
To avoid any damage to these items during transportation, the Slide Runners and Slide
Tracks have been pre-assembled together in pairs. Each pair includes a Slide Runner and
Slide Track. Before assembling your furniture, please separate the Slide Runners from the
Slide Tracks according to the below instructions.
Slide Track
Slide Runner
SAFETY & WARNINGS

4
Step 1:
Extend the Slide Runners apart from the Slide Track:
Step 2:
Gently press the plastic release lever on the Slide Runner while pulling the Slide Runner and
Slide Track apart from each other:
Step 3:
The Slide Runner and Slide Track should now be separated. Repeat these steps for all
remaining pairs of Slide Runners and Slide Tracks:
Slide Runner
Slide Track

5
Lay all components out on a clean floor and ensure all parts are included. If any pieces are
missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.
COMPONENTS

6
Fittings
A Ø15x9.6 (x42)
BL=35mm (x36)
C Ø5.5x38 (x6)
D Ø4x32 (x12)
ESlide Track (x12)
FSlide Runner (x12)
G Ø3.5x12 (x84)
H(x12)
I Ø3x18 (x12)
J Ø6x13x1
K
L Ø4x16
MH=120mm (x4)
N Ø5x16 (x20)
OH=120mm (x1)
PH=599mm (x2)
QH=68mm (x3)

7
Step 1:
BL=35mm (x24)
ASSEMBLY

8
Step 2:
FSlide Runner (x12)
G Ø3.5x12 (36)
FSlide Runner (x6)
FSlide Runner (x6)

9
Step 3:
A Ø15x9.6 (x12)
D Ø4x32 (x12)
Arrow to point in
the direction of
end hole

10
Step 4:
A Ø15x9.6 (x12)
Arrow to point in
the direction of
end hole

11
Step 5:
ESlide Track (x6)
G Ø3.5x12 (x18)
ESlide Track (x6)

12
Step 6:
These screws must assemble in the first holes of the metal runner for the left side step.
ESlide Track (x3)
G Ø3.5x12 (x9)
ESlide Track (x3)
Left side

13
Step 7:
These screws must assemble in the second holes of the metal runner for the left side step.
ESlide Track (x3)
G Ø3.5x12 (x9)
ESlide Track (x3)
Right side

14
Step 8:
BL=35mm (x6)

15
Step 9:
BL=35mm (x6)

16
Step 10:
A Ø15x9.6 (x6)
QH=68mm (x3)
Arrow to point in
the direction of
end hole

17
Step 11:
A Ø15x9.6 (x3)
Arrow to point in
the direction of
end hole

18
Step 12:
A Ø15x9.6 (x3)
Arrow to point in
the direction of
end hole

19
Step 13:
C Ø5.5x38 (x6)

20
Step 14:
MH=120mm (x4)
N Ø5x16 (x20)
OH=120mm
Stand up
Leg height is
adjustable