overstock GFM30731E User manual

GFM30731E
16
Outdoor Furniture
IMPORTANT
If you have any problems with this product (missing or damaged parts, assembly issues, etc.),
PLEASE DO NOT RETURN TO THE RETAILER/STORE
where you purchased the product.
Please call our Toll-Free Customer Service Hotline at: 1-866-988-3300
Between 8:00 AM and 5:00 PM Pacific Standard Time, Monday through Friday
To expedite any future warranty claims, please retain the instruction sheet, warranty card
and receipt for future use.
Care and Maintenance
Store furniture in an upright position. Be careful not to allow water to build up in frames, as this will cause
corrosion and freeze damage in cold climates. Wash all frames with a solution of mild soap and water.
Rinse with clean water and dry with a soft absorbent cloth towel. Frames can be treated with a liquid wax
for maximum protection against UV rays and/or salty, damp air. If your set includes cushions, slings, and/or
an umbrella, they may be cleaned by hand with a solution of soap and water with a clean water rinse.
(Never machine wash cushions, slings or umbrella covers as this will result in shrinkage or damage). After
cleaning cushions, tip on end and allow to drip dry. (Never use a commercial or home dryer to tumble dry
fabric goods). Do not use bleach or solvents to clean any product! This will void the warranty.

GFM30731E
17
Outdoor Furniture
1-Year Limited Warranty Program
For a period of one (1) year after date of purchase, the Manufacturer will either repair or replace defective components in accordance with this
Limited Warranty. This warranty is between the Manufacturer and the original purchaser and is valid only when accompanied by the original
purchaser’s sales receipt showing original date of purchase and location of purchase. Replacements under this warranty revert back to the
date of original purchase for future warranty.
The Manufacturer or its authorized dealer can accept or reject warranty claims based on its findings. This warranty applies in normal
residential use only and is not intended for commercial use. The Manufacturer can make substitutions as required of materials, components,
and sub-components of comparable value and utility. This warranty is limited to product repair or replacement (to be determined solely by the
Manufacturer). Warranty return is limited to only the single affected component.
This limited warranty covers only manufacturing defects and does not cover normal wear and tear, damage due to acts of nature (such as, but
not limited to freezing or high winds), abuse or misuse, including chemical damage from suntan oil or other chemicals, exposure to extreme
heat or cold, abrasion or excessive weight. This product is intended to be used in standard installations only. This warranty is void if the
product is not used for its intended purpose. The Manufacturer disclaims liability for any aspect of installation and any inconvenience caused
by a defective part of a component.
Certain items are not covered by this warranty. These include, but are not limited to the following:
1. Components subjected to abuse, including abuse intended to simulate failure.
2. Damages caused by retailer, shipper or installation crew (such as scratches, dents, tears, chips, etc.).
3. Any part that merely exhibits normal wear yet functions essentially as new, including chips, scratches or stretching of materials and
stitching.
4. Tears, punctures, scratches or any damage caused by improper installation or use.
5. Damage to frames/welds resulting from improper assembly or exposure to water and/or sub-freezing temperatures is not covered.
General frame rusting is not covered.
6. Fading and/or discoloration of fabrics/cushions/straps/wicker resulting from exposure to the elements, chemicals, oils, fluids or any
other cause are not covered.
7. Umbrella bases are not covered under any circumstances.
8. Items sold “as is” or floor models.
To make a claim, call the toll-free number below. Please have available a copy of the original sales receipt along with a brief description of the
problem. Please also provide your email address and daytime telephone or cell phone number. All items may be charged actual freight costs
plus $15 for handling. Repairs or replacement will be made at the Manufacturer’s option. Sales and use taxes, plus shipping and handling
charges are the responsibility of the consumer.
THIS IS THE ENTIRE EXCLUSIVE EXPRESS LIMITED LIABILITY. THE MANUFACTURER NEITHER MAKES NOR IS RESPONSIBLE FOR ANY OTHER WARRANTIES,
EITHER EXPRESS OR IMPLIED, INCLUDING THOSE OF RETAILING DEALERS. THIS EXCLUSIVE REMEDY IS LIMITED TO RECEIPT OF A CREDIT IN CONNECTION WITH
THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR COMPONENT DEEMED TO BE DEFECTIVE UNDER THE TERMS AND CONDITIONS AS STATED IN THIS
WARRANTY. NEITHER THE PRODUCT MANUFACTURER NOR ITS AGENTS SHALL BE LIABLE IN ANY CASE FOR INCIDENTAL, INDIRECT, SPECIAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY OR NEGLIGENCE EVEN IF IT
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCEPT AS OTHERWISE MAY BE REQUIRED BY LAW, THERE ARE NO OTHER EXPRESS OR IMPLIED
WARRANTIES OTHER THAN THE WARRANTY DESCRIBED HEREIN, AND ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY DISCLAIMED.
Contact Customer Service at 1-866-988-3300

Assembly Instructions
GFM30731E
11.4'x11.4x9.5' Hard Top Gazebo with
Curtains
Questions, problems, or missing parts?
Before returning to the store, call Customer Service.
1-866-988-3300
8 a.m. -5 p.m., PST Monday - Friday
Retain this manual for future use.

GFM30731E
1
Parts & Tools
PART QTY PICTURE & DESCRIPTION PART QTY PICTURE & DESCRIPTION
A 4
Post
P 4
Top Frame Plug
B 4
Long Beam 1 P1 4
Metal Plate Cover Component
B1 4
Long Beam 2 Q 8
Incline Connecting Plate
B2 8
Fabric Rod Q1 8
Middle Connecting Plate
C 4
Corner Incline Tube R 8
Incline Outer Metal Part
C1 4
Middle Incline Tube R1 4
Border Tube Outer Metal Part
C2 4
Top Corner Incline Tube
S 1
Top Plate
D 8
Short Horizontal Tube T 1
Bottom Plate
D1 8
Long Horizontal Tube T1 1
Hook
E 4
Top Frame Tube
U 16
Fabric Rod Cap

GFM30731E
2
F 4
Border Tube 1 V 4
Netting
F1 4
Border Tube 2 W 48+1
Split Ring
F2 4
Top Border Tube AA
184+1
M6x15 Combination Bolt
G 4
Top Cover Plate
BB 26+1
M6x30 Combination Bolt
G1 4
Cover Plate 1
CC 32+1
M6x40 Combination Bolt
G2 4
Cover Plate 2 DD 16+1
M6x40 Bolt
H 4
Metal Plate 1
EE 8+1
M6x75 Combination Bolt
H1 4
Metal Plate 2
FF 8+1
M6 Nut
H2 4
Metal Plate 3
GG 2+1
Plastic Washer
J 4
Metal Plate 4
HH 8+1
Ground Spike
J1 4
Metal Plate 5
II 1
Wrench
K 4
Metal Plate 6
JJ 2
Hex Wrench
K1 4
Metal Plate 7
K2
4
Metal Plate 8

GFM30731E
3
L 4
Post Base Plate
L1 4
Post Base Cap
M 4
Beam Decorator
M1 4
Beam Lining
N 4
Right Corner Support Bar
WARNING: To avoid damage of this production,
please use either the carton or another soft
surface such as carpet as a working surface to
prevent product damage during assembly.
Need for assembly:
N1 4
Left Corner Support Bar
N2 4
Corner Fitting
N3 4
Middle Fitting
WARNING: Please keep children out of the assembly area before assembly.
WARNING:
Do not leave the gazebo where there is a risk of high wind, as possible damage will occur to
the structure.
WARNING:
Keep all flame and heat sources away from the fabric.
CAUTION:
Do not climb on the top of the gazebo. Falling off the gazebo can result in serious injury
, possibly
even death.

GFM30731E
4
Gazebo Assembly
Step 1:
•Attach the post base cap (L1) and the
post base plate (L) to the posts (A)
using M6x15 combination bolts (AA).
•Repeat this step for the other three
posts (A).
•Fully tighten the bolts using the hex
wrench (JJ).
Step 2:
•Attach the long beam 1 (B) and long
beam 2 (B1) to the beam lining (M1).
•Attach the long beam 1 (B) and long
beam 2 (B1) to the beam decorator
(M) by using M6x75 combination bolts
(EE) and M6 nuts (FF).
•Do not fully tighten all the bolts at this
step.

GFM30731E
5
Step 3:
•Insert fabric rod (B2) into fabric rod cap
(U), then attach to the assembled long
beacon (B & B1) by using M6x40 bolts
(DD).
•Do not fully tighten all the bolts at this
step.
Step 4:
•Attach the assembled long beam (B &
B1) to the two posts (A) using M6x40
combination bolts (CC).
•Repeat this step for the other two posts
(A).
•Do not fully tighten all the bolts at this
step.

GFM30731E
6
Step 5:
•Attach the assembled long beam (B &
B1) to the assembled posts (A) using
M6x40 combination bolts (CC) as
shown below.
•Do not fully tighten all the bolts at this
step.
Step 6:
•Attach the left corner support bar (N1)
to the long beam 2 (B1) by using M6x15
combination bolts (AA).
•Attach the right corner support bar (N)
to the long beam1 (B) by using M6x15
combination bolts (AA).
•Attach the other end of the left corner
support bar (N1) and the other end of
the right corner support bar (N) to the
posts (A) using
M6x15 combination bolts
(AA) as shown below.
•Do not fully tighten all the bolts at this
step.

GFM30731E
7
Step 7:
•Attach the corner fitting (N2) to the
corner incline tube (C) using M6x15
combination bolt (AA).
•Attach the middle fitting (N3) to the
middle incline tube (C1) using M6x15
combination bolt (AA).
•Repeat this step for the other three
corner incline tubes (C) and the other
three middle incline tubes (C1).
•Do not fully tighten all the bolts at this
step.
Step 8:
•Attach the corner incline tube (C) to
the post (A) by using M6x15
combination bolts (AA) through the
corner fitting.
•Insert the top frame plug (P) into the
corner incline tube (C) and the top
frame tube (E) as shown below.
•Do not fully tighten all the bolts at this
step.

GFM30731E
8
Step 9:
•Attach the middle incline tube (C1) to
the assembled beam (B & B1) by using
the M6 nuts (FF) through the middle
fitting (N3).
•Insert the middle incline tube (C1) into
the top frame tube (E) as shown below.
•Do not fully tighten all the bolts at this
step.
Step 10:
•Attach the top corner incline tube (C2)
and the top border tube (F2) to the
incline outer metal part (R) using the
M6x15 combination bolt (AA) as shown
below.
•Insert the top corner incline tube (C2)
into the bottom plate (T).
•Do not fully tighten all the bolts at this
step.

GFM30731E
9
Step 11:
•Attach the metal plate 1 (H) to the top
border tube (F2) using the M6x15
combination bolts (AA).
•Do not fully tighten all the bolts at this
step.
Step 12:
•Attach the top cover plate (G) to the
metal plate 1 (H) using the M6x40
combination bolts (CC).
•Attach the top plate (S) to the bottom
plate (T) by using the M6x30
combination bolt (BB) and plastic
washer (GG).
•Screw the hook (T1) into the bottom
plate (T).
•Do not fully tighten all the bolts at this
step.

GFM30731E
10
Step 13:
•Attach the top corner incline tube (C2)
to the top frame plug (P) using the
M6x15 combination bolts (AA).
•
Attach the short horizontal tube (D), the
long horizontal tube (D1) and the
corner incline tube (C), to the incline
connecting plate (Q) using the M6x15
combination bolt (AA).
•Attach the short horizontal tube (D),
long horizontal tube (D1) and the
middle incline tube (C1), to the middle
connecting part (Q1) using the M6x15
combination bolt (AA).
•Do not fully tighten all the bolts at this
step.
Step 14:
•Attach the border tube1 (F) and the
border tube 2 (F1) to the corner incline
tube (C) using the M6x15 combination
bolts (AA).
•Attach the border tube1 (F) and the
border tube 2 (F1) to the middle incline
tube (C1) using the M6x15 combination
bolts (AA).
•Do not fully tighten all the bolts at this
step.

GFM30731E
11
Step 15:
•Attach metal plate cover component
(P1) to the metal plate 8 (K2) to using
the M6x15 combination bolts (AA).
•Do not fully tighten all the bolts at this
step..
Step 16:
•Attach the metal plate 7 (K1) and the
metal plate 6 (K) to the border tube (F
& F1) using the M6x15 combination
bolts (AA) as shown below.
•Attach the metal plate 7 (K1) and the
metal plate 6 (K) to the corner incline
tube (C) by using the M6x15
combination bolts (AA) as shown
below.
•Do not fully tighten all the bolts at this
step.

GFM30731E
12
Step 17:
•Attach the cover plate (G1) to the
assembled frame by using the M6x40
combination bolts (CC) as shown
below.
•Do not fully tighten all the bolts at this
step.
Step 18:
•Attach the metal plate 4 (J) and metal
plate 5 (J1) to border tube (F & F1)
using the M6x15 combination bolts (AA)
and M6x30 combination bolts (BB) as
shown below.
•Attach the metal plate 4 (J) and metal
plate 5 (J1) to the corner incline tube
(C) by using the M6x15 combination
bolts (AA) as shown below.
•Do not fully tighten all the bolts at this
step.

GFM30731E
13
Step 19:
•Attach the metal plate 2 (H1) and the
metal plate 3 (H2) to the border tube (F
& F1) using the M6x30 combination
bolts (BB).
•Attach the metal plate 2 (H1) and the
metal plate 3 (H2) to the corner incline
tube (C) using the M6x15 combination
bolts (AA).
•Do not fully tighten all the bolts at this
step.
Step 20:
•Attach the cover plate (G2) to the
assembled frame by using the M6x40
combination bolts (CC) as shown
below.
•Do not fully tighten all the bolts at this
step.

GFM30731E
14
Step 21:
•Attach the incline outer metal part (R)
and the border tube outer metal part
(R1) to the assembled frame using the
M6x15
combination bolts (AA) as shown
below.
•Do not fully tighten all the bolts at this
step.
Step 22:
•Once all of the bolts are in place, fully
tighten all the bolts using wrench (HH)
and hex wrench (II).
•Secure the post (A) to the ground by
using the ground spikes (HH).

GFM30731E
15
Step 23:
•
Attach the netting (V) to the assembled
gazebo by using the split ring (W) as
shown below.