OVERTOPTECH L160-1 User manual

L160-1
INSTRUCTION

3.0 safety of flight
.
1 Anyone who is experiential in model-control and no less
than fourteen is suggested to fly it.
.
2 Please don't fly under bad weather,for
。
instance,windy,rainy.snowy,lightning etc
3. Please fly at broad ground where there is little people.
.
4 Please make sure the quadcopter is more than one meter
away from people.
.
5 Please don't fly under high voltage
wire,telecommunication base station or transmitter
tower. avoid interference
.
6 Please don't fly in where it is illegal to fly.
2
3
2.0 Parameters
1、Quadcopter
Name：L160-1
Propeller：4045
Body（length*width*height） ： 185mm*140mm*42mm
Take-off weight：230g（Batteries included）
Transmitter：H-4S 6CH
Flight controller：CC3D
Video transmission：25-1000mw
Motor：1306-3100KV
Brushless Electronic speed controller：6A ESC
Battery(for quadcopter)： 3S
Flight time：7 to10 minutes
Environment temperature ：-10°to +40°
3、Camera
Resolution：720TVL
Type：PAL/NTSC
Input：DC 12V
Camera angles：127°
Resolution：1080P
Type：PAL/NTSC
Power input：8.4~12V
Video receiver channel：8CH
Transmission distance：200m-300m
Dimension：4.3 inch
2. Monitor(Video receiver built inside)
4.0 how to charge
Note：Any problem please refer B3 charger detailed
1,Insert B3 charger adapter into pocket(100~240V
50/60HZ) ,the adapter will output to B3 charger, led will turn
constant blue if connected.
2,connect the charger and battery with balance connector
3,led will be red when charging, turn blue when finish.
5.0 Assembly
5.1 Monitor
1. Assemble the holder
to the supporter on the
transmitter and screw
the other side to the
monitor
2. Screw antenna.
3. attach battery with
Velcro to the backward
of the monitor.
34
1.0 what is quadcopter
1、nice design to protect electronic speed controller
and motors, looks pretty.
2、3K carbon fiber composit, high agility, flexibility
and pressureproof.
3、5.8G live transmission system which give you new
sight experience.
4、it can flip forward-backward,left-righ.you can do
lots of acrobatics. .
7. Receiver
8. Video transmission
9. Mushroom antenna
1. Motor
2. CCW Propeller
3. CW Propeller
4. Camera
5. ESC (Simonk )
6. Flight controller
CATALOG
2
3
3
4
4
4
5
5
6
6
7
8
10
10
10
1.0 What is quadcopter
2.0 Parameters
3.0 Safety of flight
4.0 How to charge
5.0 Assembly
5.1 Monitor
5.2 Propellers
5.3 Batteries
6.0 Prepare for flight
6.1 Turn radio on
6.2 Lock/unlock
7.0 Operations
8.0 Ends
9.0 Additional instruction
9.1 4.3 inch integrated video receiver & monitor instruction
1
4
6
8
7
5
22
3
9
12

Mode 2Mode 1
Transmitter（mode 1)
Transmitter（mode 2)
6.2 Unlock/lock
Unlock：
turn the throttle stick lowest, turn direction stick to right
and last more than 5 minutes. It will be unlocked when
light turn blue. motors will rotate if you turn throttle
upward.
Mode 1(right throttle) Mode 2(left throttle)
direction stick
throttle stick
throttle direction stick
Rotation stick
Ch5 Novice/self-leveling
mode when switch “0”
CH5 Advanced mode when
switch “1”
Note：
1、Advanced mode requires a
broad ground.
2、Advanced mode is
recommended to experiential
pilot
Advanced mode makes quadcopter
fly more bitter, so please turn
throttle upward appropriately when
quadcopter is low, turn throttle
downward appropriately when
quadcopter is high
direction control( indicate head)
up/down
up/down
Mode 2Mode 1
78
7.0 Operating instructions
5.3 Battery
Paste lipo battery(can range from 1000mah to
2200mah, 3S or 4S capable) to the top plate with
Velcro, make the head and rear balanced. Then chain
the battery with strap tightly.。
5.2 Propeller
Screw counter clockwise propellers which be printed
6045 to
right front of quadcopter and left rear of quadcopter.
similarly
screw clockwise propellers which be printed 6045R to
left front of quadcopter and right rear of quadcopter.
like the picture shows.please make sure everything
propellers be screwed correctly and tightly.
5.4 how to balance quadcopter ?
hang quadcopter at the center of the quadcopter, if it
tilt forward,please move battery backward then try again.
similarly if it tilt backward, please move battery forward
and try again.
6 Prepare for flight
6.1 Turn transmitter /monitor on
Transmitter
1.turn all functions switch upward, turn the throttle stick
lowest. turn transmitter on .mode 1 stands for right throttle
while mode 2 stands for left throttle.
2、put the quadcopter on the ground horizontally, power
the quadcopter on
3、if the quadcopter tweet and the receiver turn
constant green, the transmitter has succeeded to
connect to the quadcopter. It's ready to go. If failed,
please refer XX page
4、Power on monitor
Battery
4045R
4045R
4045
4045
Head
56
Center
Head

Transmitter（mode 2)
Transmitter（mode 1)Transmitter（mode 1 or 2)
direction control( indicate head)direction control( indicate head)
forward/backward
forward/backward
left/right
Counter clockwise/clockwise
8.0 END
9.0 Additional instruction
1.quadcopter landing。 2.Power off quadcopter。
3.Turn off transmitter 4.Power off monitor
1. 4.3 inch integrated video receiver & monitor instruction
There are 8 optional receive channels. choose which is best for
video transmission.
Following form shows these 8 channels
91 0
CH1
FR1(A)
CH3
FR3(E)
CH2
FR2(B)
CH4
FR4(F)
CH5
CH7
CH6
CH8
123456
123456
123456
123456
123456
123456
123456
123456
123456
123456
123456
123456
Fr1 or (A)
Fr1 or (B)
Fr1 or (E)
Fr1 or (F)
1 1 1 2
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
CH
FR
5865
5733
5705
5740
5845
5752
5685
5760
58055825
57905771
56455665
58005780
5785
5809
5885
5820
5765
5828
5905
5840
5745
5847
5925
5860
5725
5866
5945
5880
CH
FR
ON ON ON ON ON ON ON ON
123 123 123 123 123 123 123 123
5945MHz 5925MHz 5905MHz 5885MHz 5645MHz 5665MHz 5685MHz 5705MHz
12345678
Channel
Frequency
Switchers
Position
A
B
A:12 LED indicators show frequency band
and channel
B:Button
Default power on frequency is F1
Long press right button to change band
LED: A-B-E-F circularly Short press right
button to change channel LED:1-2-3-4-5-
6-7-8 circulary Power off memory for last
frequency
Figure and receive
Figure the launch
Tune radio
For Mushroom
Turn transmitter on,turn throttle stick down at lowest.power
on quadcopter,the light on receiver will turn red.press the
button on receiver and don't leave until the light turn green.it
indicates transmitter has
antennas, please screw one which
pasted in TX to video transmission, screw the other one
pasted in RX to video receiver built in monitor