OVO KIT-033-BK User manual

User Manual
Power Nozzle Kit
Model Number:
For the product video
Scan the QR code or visit YouTube video
at: https:/ /youtu.be/hJ9E5-jdjr8
KIT-033-BK

Index
1. Specifications .................................................................................................................. 3
2. Instructions...................................................................................................................... 4-5
3. How to replace the belt ................................................................................................... 6-7
4. How to replace the Roller brush ..................................................................................... 8-9
5. How to replace the light.......................................................................................................10
6. What to do when clogging............................................................................................... 11
7. Trouble shooting .............................................................................................................12
Page 2

1. SPECIFICATIONS
Carpet Beater (Power head)
High-Voltage wand ( included)
1
23
45
6
7
1. Brush roll ON/OFF switch
2. Overload protector reset
3. Carpet height indicator
4. Dirt sensor
5. Carpet height adjustment
6. Handle position release
7. Wand release latch
1. Hose nozzle release button
2. Hose nozzle connection
3. Wand extension handle
4. Carpet beater connection
FROM 25.5
TO 38’’
12
3
4

2. INSTRUCTIONS
Connecting the wand to the electric carpet beater (powerhead)
Connecting the high-voltage hose to the wand
Page 4
Carpet beater (Powerhead) port
The OVO electric carpet beater
(powerhead) has male ports to
connect to the electric wand.
Hose port
The hose nozzle must have two
female ports in order to connect
it to the wand. (Hose not
included.)
Wand ports
Our electric wand has 2 male
ports.
Connection
Align the female ports from the
hose nozzle with the male ports
on the wand and push the hose
nozzle into the wand.
Wand port
The OVO electric wand has female
ports to connect to the electric
carpet beater (powerhead).
Connection
To connect the wand to the electric
carpet beater, align the female ports
(from the wand) and the male
connectors (from the carpet beater),
then push the wand into the beater.
2.1 Carpet beater
port 2.2 Electrical wand port 2.3 Connection or the wand to the beater
2.4 Hose nozzle port 2.5 Electrical wand
port 2.6 Connection of the hose nozzle to the wand

Page 5
2. INSTRUCTIONS (cont.)
How to use the carpet beater
-
The ON-OFF switch for the carpet
beater is located on the top, as
illustrated (M).
The carpet beater switch must be ON
to activate the roller and the switch
on the hose must be ON to activate
the suction.
You can adjust the height of the carpet
beater by pushing on the pedal, as
illustrated (N).
You will see the beater’s level by
looking through the carpet height
indicator (O).
The wand can be moved up and
down by pressing on the pedal
under the beater, as illustrated (K).
When the wand is in the upright
position, it will be locked and will
stay in place.
The dirt sensor (J) will turn red when
the carpet beater is detecting and
picking up dirt.
The light will turn green when there
is no more dirt to pick up.
2.7 ON-OFF Switch
2.8 Adjustable heights
2.9 Upright postion lock
2.10 Dirt sensor

3. HOW TO REPLACE THE BELT
Belt Replacement
Page 6
STEP 1 STEP 2 STEP 3
ALWAYS DISCONNECT THE VACUUM AND THE HIGH-VOLTAGE HOSE FROM THE
ELECTRICAL OUTLET BEFORE PROCEEDING WITH THE FOLLOWING MAINTENANCE.
Always follow these procedures to verify or replace the belt in order to avoid damaging
the carpet beater.
The belt installed in the electric carpet beater (powerhead) makes the brush roll turn. It has been specifically designed for
our electric carpet beater and is required to ensure a flawless operation.
1-Disconnect the wand from the
electric carpet beater (powerhead).
2-Turn the electric carpet beater
(powerhead) so that the bottom is
facing you.
3-Remove the 7 screws as illustrated
above.
Turn the electric carpet beater
(powerhead) so that the top part is
facing you and lift the cover (B) to
remove it.
To remove the brush roll cover,
remove the screws as illustrated
above and lift the cover to remove it.
Do not remove the 3
screws in a triangle
formation as these hold
the motor in place
Unscrew the
powerhead cover Remove the powerhead cover Remove the brush roll cover

3. HOW TO REPLACE THE BELT (cont.)
Page 7
STEP 4
STEP 7 STEP 8
STEP 5 STEP 6
If the belt is stretched or cut, pull it
out from the motor pulley, as
illustrated above.
1-Put the brush roll cover back over
the brush roll.
2-Replace the 2 screws and make
sure the cover is well attached.
1-The wand port must be in the
upright position and locked in place.
2-Put the cover back on top of the
electric carpet beater (powerhead).
3-Turn the carpet beater (power-
head) over.
4-Replace the screws, as illustrated in
step 1.
1-Lift the end of the brush roll.
2-Remove the old belt and replace it
with the new one. Make sure the
lettering is facing you and that it is
visible.
3-Stretch the belt and attach it to the
motor pulley.
Verify/remove
the belt
Replace the
brush roll Replace the carpet beater (powerhead) cover
Remove/replace
the belt
1-Hold the opposite end of the brush
roll in place.
2-Push the belt end forward and
down while rotating the endplate
until it slides into place.
3-Turn the brush roll to make sure it
rotates freely.
Replace the
brush roll
STEP 9
Replace the 7 screws as illustrated
above.
Screw the powerhead
cover in place

4. HOW TO REPLACE THE BRUSH ROLL
Page 8
To check if the brush roll needs to be changed, slide cardboard across the bottom plate while
turning the brush roll. If the brushes do not touch the cardboard, it is time to change the
brush roll.
Always follow these procedures to verify or replace the brush roll in order to avoid
damaging the carpet beater.
STEP 1 STEP 2 STEP 3
1-Disconnect the wand from the
electric carpet beater (powerhead).
2-Turn the electric carpet beater
(powerhead) so that the bottom is
facing you.
3-Remove the 7 screws as illustrated
above.
Turn the electric carpet beater
(powerhead) so that the top part is
facing you and lift the cover (B) to
remove it.
To remove the brush roll cover,
remove the screws as illustrated
above and lift the cover to remove it.
Do not remove the 3
screws in a triangle
formation as these hold
the motor in place
Unscrew the
powerhead cover Remove the powerhead cover Remove the brush roll cover

4. HOW TO REPLACE THE BRUSH ROLL (cont.)
Page 9
Always follow these procedures to verify or replace the brush roll in order to avoid
damaging the carpet beater.
STEP 5 STEP 6
Replace the brush roll
cover Replace the carpet beater (powerhead) cover
STEP 4 STEP 5
1- Lift the end of the brush roll to
release the belt.
2- Remove the old brush roll and
replace it with the new one.
3- Loop the belt around to the motor
pulley.
4- Make sure the belt is sitting in the
“belt groove” on the brush roll.
Remove/replace the
brush roll
1-Hold the opposite end of the brush
roll in place.
2-Push the belt end forward and
down while rotating the endplate
until it slides into place.
3-Turn the brush roll to make
sure it rotates freely.
Replace the
brush roll
STEP 7 Screw the powerhead
cover in place
1-Put the brush roll cover back over
the brush roll.
2-Replace the 2 screws and make
sure the cover is well attached.
1-The wand port must be in the
upright position and locked in place.
2-Put the cover back on top of the
electric carpet beater (powerhead).
3-Turn the carpet beater (power-
head) over.
4-Replace the screws, as illustrated in
step 1.
Replace the 7 screws as illustrated
above.

Page 10
.
Always follow these procedures to verify or replace the head light in order to avoid
damaging the carpet beater.
5. HOW TO REPLACE THE HEAD LIGHT
STEP 1 STEP 2
Do not remove the 3
screws in a triangle
formation as these hold
the motor in place
STEP 3
STEP 4 STEP 5
Replace the
lightbulb
The light is on when the vacuum is on. If the light does not turn on, this means it is burned out
and needs to be changed. Follow the steps below to achieve this.
Remove the old bulb from the socket
and replace it with the new one.
1-Disconnect the wand from the
electric carpet beater (powerhead).
2-Turn the electric carpet beater
(powerhead) so that the bottom is
facing you.
3-Remove the 7 screws as illustrated
above.
Turn the electric carpet beater
(powerhead) so that the top part is
facing you and lift the cover (B) to
remove it.
Unscrew the
powerhead cover Remove the powerhead cover
Put the carpet beater cover
back in place Screw the power head
cover back in place
1-The wand port must be in the
upright position and locked in place.
2-Put the cover back on top of the
electric carpet beater (powerhead).
3-Turn the carpet beater (power-
head) over.
4-Replace the screws, as illustrated in
step 1.
Replace the 7 screws as illustrated
above.

Page 11
STEP 6 STEP 7
STEP 4 STEP 5
5. CLOG IN THE POWER NOZZLE
If the carpet beater (powerhead) gets clogged, use the following procedure to check and clear the blockage.
If the clogging is severe enough, the
power nozzle will stop operating.
Once you clear the blockage, press
the overload protection reset button
(A) and the power nozzle will start
working again.
You will find an additional panel at
the bottom of the power nozzle (C).
This opening provides a secondary
place to check for blockages.
STEP 1 STEP 2 STEP 3
1-Disconnect the wand from the
electric carpet beater (powerhead).
2-Turn the electric carpet beater
(powerhead) so that the bottom is
facing you.
3-Remove the 7 screws as illustrated
above.
Turn the electric carpet beater
(powerhead) so that the top part is
facing you and lift the cover (B) to
remove it.
To remove the brush roll cover,
remove the screws as illustrated
above and lift the cover to remove it.
Do not remove the 3
screws in a triangle
formation as these hold
the motor in place
Unscrew the
powerhead cover Remove the powerhead cover Remove the brush roll cover
Replace the
brush roll
Replace the carpet beater
(powerhead) cover
Locate the blockage. Clean the beater
brush and remove the dirt that
created the clogging.
Locate and clean out
the blockage Screw the powerhead cover in place
1-Hold the opposite end of the brush
roll in place.
2-Push the belt end forward and
down while rotating the endplate
until it slides into place.
3-Turn the brush roll to make sure it
rotates freely.
1-The wand port must be in the
upright position and locked in place.
2-Put the cover back on top of the
electric carpet beater (powerhead).
3-Turn the carpet beater (power-
head) over.
4-Replace the screws, as illustrated in
step 1.
Replace the 7 screws as illustrated
above.

Page 12
Service problems that appear to be major can often be solved easily.
You can be your own troubleshooter by reviewing this guide.
Problem Check Solution
CHECK THESE FIRST
4- TROUBLESHOOTING
Power nozzle
won’t turn ON
receptacle on nozzle.
reset reset.
Power nozzle
still does not
operate properly
7. TROUBLE SHOOTING GUIDE

2044 Autoroute 440 Ouest, Laval, QC, H7S 2M9
TO REGISTER YOUR WARRANTY:
USA: www.myovo.net
Canada: www.myovo.ca
USA: myovo.net/register
Canada: myovo.ca/registrer
1 800 776-7891
TO GET THE PARTS OR OTHER PRODUCTS:
USA: myovo.net
CANADA: myovo.ca
EMAIL AT: [email protected]
TOOL FREE: 1-800-776-7891