Owon SEG-X5 ZigBee User manual

SEG-X5 ZigBee Gateway
Quick Sta Guide

2
WARNING: Failure to follow these safety notices could result
in re, electric shock, other injuries, or damage to the gateway
and other property. Read all the safety notices below before
using the gateway.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet
light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or t to repair the unit on your own.
• Do not expose the unit or its accessories to ammable liquids,
gases or other explosives.
• Do not use harsh chemicals or strong detergents to clean it.
• Do not place it where infants and young children can touch,
children should use under parental supeision.
• Do not touch it when powering on to ensure your safety.
• Indoor use only.
Safety Handling

3
Connectivity
Ethernet RJ45 Po • 10/100M bps
• Auto MDIX
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Prole • ZigBee 3.0
RF Characteristics
• Operating frequency: 2.4 GHz
• Internal PCB Antenna
• Range outdoor: 100m (open area)
Physical Specications
Operating Voltage • Micro-USB DC5V/2A
Operating environment
• Temperature: -20 ℃~+55 ℃
• Humidity: ≤ 90%
non-condensing
Dimensions • 91.5(W) x 133 (L) x 28.2(H) mm
Mounting Type • Tabletop stand or Wall mounting
Technical Specications

4
Welcome
1
The SEG-X5 Sma Gateway acts as a central platform for your
sma home system. It allows you to add ZigBee devices into the
system. Automatic control, schedule, scene, remote monitoring
and control for ZigBee devices can enrich your IoT experience.
This guide will provide you with an oveiew of the product and
help you get through the initial setup.
• ZigBee 3.0
• Stable internet connection via Ethernet
• ZigBee coordinator of the home area network and provide
stable ZigBee connection
• Built-in buzzer
• Local linkage, scenes, schedules
• Suppo backup & transfer to replace gateway
Features:

5
2Get to know your device
Cloud connection Sub-devices
Wi-Fi
(Optional)
Sub-devices indicator
The status gives the following information:
Cloud connection indicator
The status gives the following information:
① Indicator
LED Color Status What it means
Green Always-on Connected to the cloud Successfully
Orange Flashes slowly Failed to connect to the cloud
Always-on In conguration mode
LED Status What it means
Flashes rapidly Allow sub-devices to join the gateway

6
ZigBee button
Wi-Fi button USB-A
Micro-usb
ZigBee button
• Permit join: Press and hold it for 2 seconds until the Sub-
devices indicator flashes rapidly to allow sub-devices to join
the gateway which will last 2 min, you can hold it again for 2
seconds to exit it.
② Button
System-initiated
After you reset the gateway or when it is powered on, the Cloud
connection indicator and the Wi-Fi / Sub-devices indicator will be
always-on at the same time.
Firmware upgrade
When the gateway rmware is upgrading, the Cloud connection
indicator and the Wi-Fi / Sub-devices indicator will ash slowly at
the same time.

7
Reset Button
• Reset: Press and hold the reset button for 10 seconds until the
buzzer beeps to restore the gateway to default facto setting.
The gateway has a built-in buzzer, the status gives the following
information:
③ Buzzer
Status What it means
One long beep Rest the gateway
Beep twice quickly In conguration mode
Beep twice evenly Sub-device successfully joined the gateway
3Get Staed
3.1 Installation
1. The gateway needs power supply and Ethernet connection,
so please nd a suitable position to install. You can mount the
gateway on the wall using its wall bracket or put it on a flat
suace.
2. Once the best position has been identied, inse the micro-
usb cable to the POWER po and connect it to power supply.
3. Connect the LAN po on the gateway with the LAN po on
your router through the network cable, then wait for the cloud
connection indicator on the gateway turn green, which means
the gateway has successfully connected to the cloud.
4. After that, open the app and follow the instructions to add
gateway.

8
3.2 Add sub-devices
Please refer to the manual of your sub-device for the adding
operation, then enable permit join on gateway. When the sub-
device successfully joins the gateway, the buzzer will beep
twice evenly.