Oypla 4642 User manual

Page 1
Model Code: 4642
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 4642
Contents
1Front Cover
-
2Safety
Instructions
-
3/4 Assembly
Instructions
-
5Back Cover
End
Garage Stool

Page 2
Model Code: 4642
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3/4 Assembly
Instructions
-
5Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
This product is not a toy, and is
only to be used for its
designated purpose.
Never carry out any alterations
or modifications to this
product.
Only use this product on stable,
level and dry ground.
Always keep your hands and
feet away from the immediate
working area.
Before using the product, make
sure all fastenings are tightly in
place and that everything is in
order, and checked
periodically.
Leaving this product outside
exposed to weather, especially
direct sun, rain and salt air, will
speed with the weathering
process. This can be slowed by
removing the product from
these conditions, or covering it
with a suitable cover.
When not in use the lift must
be stored in the lowest position
n in a dry location.
This product is not intended for
use by persons (including
children) with reduced physical,
sensory and mental capacities,
or lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use of
the product by persons
responsible for their safety.
Clean only with a damp cloth.
Do not use strong industrial
cleaning substances or abrasive
materials as these will damage
the product. Do this regularly
to keep the product clean of
any oil or grease.
If the product is damaged or
has any defects, please contact
[email protected].

Page 3
Model Code: 4642
Oypla.com LLP / www.oypla.com
Parts List:
-If you are missing any of the below parts, please contact [email protected]
-Please be aware that you will be referring to this parts list throughout the assembly
process.
Item No.
Description
Quantity
1
Seat
1
2
Steel Frame
2
3
Screw for Seat
2
4
Nut for Saddle
4
5
Nut for Wheel
4
6
Washer
4
7
Plastic Saddle
1
8
Steel Unit
1
9
Screw for Saddle
4
10
Rear Caster Wheel
4
11
Trasome
2
Contents
1Front Cover
-
2Safety
Instructions
-
3/4 Assembly
Instructions
-
5Back Cover
End
Assembly Instructions

Page 4
Model Code: 4642
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3/4 Assembly
Instructions
-
5Back Cover
End
1) Firstly, as seen on the diagram on
the previous page, push the plastic
saddle (7) onto the steel unit (8)
ensuring the holes align. Now take 1
steel frame (2) and secure it to the
plastic saddle and steel unit, using 2
large screws (9), nuts (4) and washers
(6). Please ensure screws are fully
tightened and see pictures below for
help. Repeat on the other side with
the remaining steel frame.
2) Next, attach the seat (1) to the top of the steel
frames (2). Secure in place with the 2 remaining
screws (3), located on the underside of the seat. You
should require allen key for this step. Please see
pictures to help. Red arrows show where the screws
should go.

Page 5
Model Code: 4642
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3/4 Assembly
Instructions
-
5Back Cover
End
3) Lastly, take 1 nut for the wheel (5)
and 1 wheel (10). As seen on the
image, the nut is at the top and the
wheel is at the bottom. Feed the
wheel through the pre-drilled hole
and secure in place using the nut.
Ensure tightly fixed, then repeat with
the remaining 3 wheels and nuts
until the stool is fully assembled. An
allen key again may be required.