Oypla HOME 3395 User manual

Page 1
Manual Version: v1.0
Model Code: 3395
Oypla.com LLP / www.oypla.com
User Manual
Model Code: 3395
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
4Cleaning and
Maintenance
-
4 Technical
Information
-
5Back Cover
End
Energy Saving
Floor Lamp

Page 2
Manual Version: v1.0
Model Code: 3395
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
4Cleaning and
Maintenance
-
4 Technical
Information
-
5Back Cover
End
Safety Instructions
Notice: Ensure you read and fully understand instructions before use
While every attempt is made to ensure the highest degree of protection in all equipment, we cannot
guarantee freedom from injury. The user assumes all risk of injury due to use. All merchandise is sold
on this condition, which no representative of the company can waive or change.
•This product is not a toy, and is only to
be used for its designated purpose.
•Never carry out alterations or
modifications to this product.
•This product is intended for indoor use
only.
•Do not use this product if the power
cable, or any part of the product, is
damaged.
•Only use this product on a stable, level
and dry surface.
•
This appliance can be used by children
aged from 8 years and above, and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning the use of the device in a
safe way and understand the hazards
involved.
•Ensure the power supply to the socket
into which the appliance is plugged, is in
accordance with the rating label on the
appliance and that the socket is earthed.
•To protect against electrical shock, do
not immerse the cord, plug, or any part
of this appliance into water or any other
liquids.
•Do not leave the product switched on for
extended period of times, as this can
cause the bulb to become hot,
decreasing the overall lifespan of the
bulb.
•Do not leave this product unsupervised.
If you have to leave the surroundings of
the product, always switch it off first.
•Ensure the power cord is left in a place
where it is not a tripping risk.
•If the product is damaged or defective,
please contact cserv[email protected]
⚠Beware of overheating. Do not leave
this lamp on for extended periods of time,
overnight for example.
Warnings
⚠Keep this lamp away from all liquids.
Failure to do so exposes the user to electrical
shock.

Page 3
Manual Version: v1.0
Model Code: 3395
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
4Cleaning and
Maintenance
-
4 Technical
Information
-
5Back Cover
End
Assembly Instructions
To assemble your lamp, please follow the below instructions and accompanying
diagram.
1. Remove all of the lamp parts from
the carton, and carefully place them
to one side.
2. Take the “flex pole”and thread the
power cord through the lower pole.
Twist the lower pole clockwise into
the flex pole, taking care not to pinch
the wires.
3. Connect the two ends of the power
cord, using the lock connectors.
4. Remove the rubber part, and
connect the metal connector with
the base, before removing the screw
from the metal connector.
5. Check the direction of the lamp,
before aligning the lower pole with
the base using the small screw hole.
6. Re-insert the screw that you
removed in step 4. Be careful to not
over-tighten the screw as this may
damage the product.
Light Bulb Installation
1. Insert the bulb into the clips on the
lamp head. Put one side of the bulb
against one clip, before softly
pushing the second clip to insert the
other side of the bulb.
2. Gently push the bulb into the socket.
When the bulb is inserted fully, you
will notice a click.
3. To replace/remove the bulb, follow
the above instructions in reverse
order.

Page 4
Manual Version: v1.0
Model Code: 3395
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
4Cleaning and
Maintenance
-
4 Technical
Information
-
5Back Cover
End
Technical Information
Cleaning & Maintenance
Please refer to the instructions below in regards to cleaning and maintaining your
product.
•Clean only using a dry or slightly damp
cloth. Do not use any harsh or industrial
cleaning substances, or any abrasive
materials, as these may damage the
product.
•If using a damp cloth, ensure no water
enters the body of the lamp. If it does,
ensure the lamp is completely dry before
using again.
•Ensure the lamp is switched off before
attempting any cleaning.
•Ensure that the lamp has cooled down
completely before attempting any
cleaning.
•Always unplug the plug from the socket
outlet before attempting any cleaning.
•Voltage: 220-240V
•Hertz: 50/60Hz
•Wattage: 27W
•Light Temperature: 6400K
•360 Degree “Goose Neck”Design
•Bulb: FML-27W

Page 5
Manual Version: v1.0
Model Code: 3395
Oypla.com LLP / www.oypla.com
Contents
1Front Cover
-
2Safety
Instructions
-
3Assembly
Instructions
-
4Cleaning and
Maintenance
-
4 Technical
Information
-
5Back Cover
End