Ozeri OZH1 User manual
INSTRUCTION MANUAL
AND WARRANTY
Copyright 2014, Ozeri
2
GENERAL SAFETY
Thank you for purchasing the Ozeri Dual Zone Ceramic Heater and Fan. This product
has passed extensive quality assurance tests for residential use. Every care has been
taken to ensure that it reaches you in perfect condition.
Warning: When using electric appliances, basic safety precautions should be
followed to reduce the risk of re, electric shock and personal injury, including
(but not limited to) the following:
Read all these instructions before attempting to operate this product and save these
instructions for future reference:
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY
MARKINGS IN THIS MANUAL AND ON THE APPLIANCE
When using an electrical appliance, basic precautions should always be followed,
including the following:
WARNING
THE HEATER AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS:
• Pacemakers and debrillators may be affected by strong magnetic elds. If you or
someone in your household has a pacemaker or debrillator, avoid placing the
remote control in a pocket or near the device.
• Credit cards and electronic storage media my also be affected by magnets and
should be kept away from the remote control and the top of the heater.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• This heater is hot when in use and for a short period after use. To avoid burns, do
not let bare skin touch hot surfaces. When moving the heater, hold it by the base,
not the air loop amplier.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes
and curtains, at least 3 feet (0.9 m) from the front of the heater and keep them away
from the sides and rear when the heater is plugged in.
• Extreme caution is necessary when any heater is used by or near children or inrm
persons and whenever the heater is left operating and unattended.
• Do not allow to be used as a toy. Close attention is necessary when used by or near
young children. Children should be supervised to ensure that they do not play with
the heater or remote control.
• This heater and remote control are not intended for use by young children or inrm
persons with reduced physical, sensory or reasoning capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
by a responsible person concerning use of the heater to ensure that they can use it
safely.
• The base must be tted securely before operating. Do not dismantle or use without
the base tted.
• Suitable for dry locations ONLY. Do not use outdoors or on wet surfaces. Do not
use in bathrooms, laundry areas and similar indoor locations. Never locate the
heater where it may fall into a bath or other water container. Do not use or store
where it may get wet or in the immediate surroundings of a bath, a shower or a
swimming pool.
• A heater has hot parts inside. Do not use it in areas where gasoline, paint, or
ammable liquids are used or stored or where their vapors are present. Do not use
in conjunction with or directly next to an air freshener or similar product.
• Do not locate directly below a main electricity supply outlet.
• Always plug directly into a wall outlet. Never use with an extension cord or
relocateable power tap (outlet/power strip) as overloading may result in the cord
overheating and catching re.
• Do not handle any part of the plug or heater with wet hands.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not stretch the cord or place the cord under strain. Do not run the cord under
carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do
not route the cord under furniture or appliances. To avoid a tripping hazard
arrange the cord away from trac area so that it will not be tripped over.
• Do not use with a damaged cord or plug. If the supply cord is damaged it must be
replaced by an Ozeri service agent or similarly qualied persons in order to avoid
a hazard.
• To disconnect the heater, turn the controls off, then remove the plug from the
outlet. Always unplug the heater when not in use.
• Do not use if the heater malfunctions or has been dropped or damaged in any
manner. Contact the Ozeri Helpline or return to an authorized service facility for
examination and/or repair.
• To prevent a possible re, do not use with any opening or exhaust blocked, and
keep free of dust, lint, hair, and anything that may reduce airow. Do not put any
object into the inlet grill or the exhaust opening as this may cause an electric
shock or re, or damage the heater.
• Do not use on soft surfaces, such as a bed, where openings may become blocked.
• Use only as described in this Ozeri Operating Manual. Any other use not
recommended by the manufacturer may cause re, electric shock, or injury to
persons.
• In order to avoid overheating and re hazard, do not cover the heater.
• Choking hazard: the remote control unit contains a small battery. Keep the remote
control away from children and do not swallow the battery. If the battery is
swallowed, seek medical advice at once.
• Check your heater cord and plug connections. A loose tting outlet can cause the
plug to overheat and/or cause a re. Be sure the plug ts tight in the outlet. Check
frequently during use to make sure plug and outlet are not hot. If so, discontinue
using heater and have outlet replaced by a qualied electrician. Note: Heaters
draw more current than small appliances, overheating of the outlet may occur
even if it has not occurred with the other appliances.
• The heater should be positioned so the airow is directed away from any walls or
room corners.
IMPORTANT SAFETY FEATURES
For your safety this heater is tted with automatic cut-out switches that
operate if the heater tips over or overheats. If the switches operate, unplug the
heater and allow it to cool. Before restarting the heater check and clear any
blockages and ensure the heater is on a solid level surface.
It is normal for the plug to feel warm to the touch; however, if there is a loose t
between the plug and the outlet or the plug becomes very hot, the outlet may need
to be replaced. Check with a qualied electrician to replace the outlet.
READ AND SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
POLARIZATION INSTRUCTIONS
This heater has a polarized plug (one blade is wider than the other). To reduce the risk
of electric shock, this plug is intended to t in a polarized outlet only one way. If the
plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a
qualied electrician. Do not attempt to defeat this safety feature.
TECHNICAL SPECIFICATIONS
Model OZH1
Name Ultra-thin heater
Voltage / Frequency 120V / 60Hz
Power Low:800W / High:1500W
Wind speed ≥ 1.3 m/s
Oscillation 76º
Timer 1-12 hours
Noise level ≤50dB（1m distance）
Tip-over Protection 40 ± 10°
Size Φ260*845 mm
Net Weight 4.3 kg
Gross Weight 5.2 kg
3
GENERAL SAFETY
Thank you for purchasing the Ozeri Dual Zone Ceramic Heater and Fan. This product
has passed extensive quality assurance tests for residential use. Every care has been
taken to ensure that it reaches you in perfect condition.
Warning: When using electric appliances, basic safety precautions should be
followed to reduce the risk of re, electric shock and personal injury, including
(but not limited to) the following:
Read all these instructions before attempting to operate this product and save these
instructions for future reference:
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY
MARKINGS IN THIS MANUAL AND ON THE APPLIANCE
When using an electrical appliance, basic precautions should always be followed,
including the following:
WARNING
THE HEATER AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS:
• Pacemakers and debrillators may be affected by strong magnetic elds. If you or
someone in your household has a pacemaker or debrillator, avoid placing the
remote control in a pocket or near the device.
• Credit cards and electronic storage media my also be affected by magnets and
should be kept away from the remote control and the top of the heater.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• This heater is hot when in use and for a short period after use. To avoid burns, do
not let bare skin touch hot surfaces. When moving the heater, hold it by the base,
not the air loop amplier.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes
and curtains, at least 3 feet (0.9 m) from the front of the heater and keep them away
from the sides and rear when the heater is plugged in.
• Extreme caution is necessary when any heater is used by or near children or inrm
persons and whenever the heater is left operating and unattended.
• Do not allow to be used as a toy. Close attention is necessary when used by or near
young children. Children should be supervised to ensure that they do not play with
the heater or remote control.
• This heater and remote control are not intended for use by young children or inrm
persons with reduced physical, sensory or reasoning capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
by a responsible person concerning use of the heater to ensure that they can use it
safely.
• The base must be tted securely before operating. Do not dismantle or use without
the base tted.
• Suitable for dry locations ONLY. Do not use outdoors or on wet surfaces. Do not
use in bathrooms, laundry areas and similar indoor locations. Never locate the
heater where it may fall into a bath or other water container. Do not use or store
where it may get wet or in the immediate surroundings of a bath, a shower or a
swimming pool.
• A heater has hot parts inside. Do not use it in areas where gasoline, paint, or
ammable liquids are used or stored or where their vapors are present. Do not use
in conjunction with or directly next to an air freshener or similar product.
• Do not locate directly below a main electricity supply outlet.
• Always plug directly into a wall outlet. Never use with an extension cord or
relocateable power tap (outlet/power strip) as overloading may result in the cord
overheating and catching re.
• Do not handle any part of the plug or heater with wet hands.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not stretch the cord or place the cord under strain. Do not run the cord under
carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do
not route the cord under furniture or appliances. To avoid a tripping hazard
arrange the cord away from trac area so that it will not be tripped over.
• Do not use with a damaged cord or plug. If the supply cord is damaged it must be
replaced by an Ozeri service agent or similarly qualied persons in order to avoid
a hazard.
• To disconnect the heater, turn the controls off, then remove the plug from the
outlet. Always unplug the heater when not in use.
• Do not use if the heater malfunctions or has been dropped or damaged in any
manner. Contact the Ozeri Helpline or return to an authorized service facility for
examination and/or repair.
• To prevent a possible re, do not use with any opening or exhaust blocked, and
keep free of dust, lint, hair, and anything that may reduce airow. Do not put any
object into the inlet grill or the exhaust opening as this may cause an electric
shock or re, or damage the heater.
• Do not use on soft surfaces, such as a bed, where openings may become blocked.
• Use only as described in this Ozeri Operating Manual. Any other use not
recommended by the manufacturer may cause re, electric shock, or injury to
persons.
• In order to avoid overheating and re hazard, do not cover the heater.
• Choking hazard: the remote control unit contains a small battery. Keep the remote
control away from children and do not swallow the battery. If the battery is
swallowed, seek medical advice at once.
• Check your heater cord and plug connections. A loose tting outlet can cause the
plug to overheat and/or cause a re. Be sure the plug ts tight in the outlet. Check
frequently during use to make sure plug and outlet are not hot. If so, discontinue
using heater and have outlet replaced by a qualied electrician. Note: Heaters
draw more current than small appliances, overheating of the outlet may occur
even if it has not occurred with the other appliances.
• The heater should be positioned so the airow is directed away from any walls or
room corners.
IMPORTANT SAFETY FEATURES
For your safety this heater is tted with automatic cut-out switches that
operate if the heater tips over or overheats. If the switches operate, unplug the
heater and allow it to cool. Before restarting the heater check and clear any
blockages and ensure the heater is on a solid level surface.
It is normal for the plug to feel warm to the touch; however, if there is a loose t
between the plug and the outlet or the plug becomes very hot, the outlet may need
to be replaced. Check with a qualied electrician to replace the outlet.
READ AND SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
POLARIZATION INSTRUCTIONS
This heater has a polarized plug (one blade is wider than the other). To reduce the risk
of electric shock, this plug is intended to t in a polarized outlet only one way. If the
plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a
qualied electrician. Do not attempt to defeat this safety feature.
TECHNICAL SPECIFICATIONS
Model OZH1
Name Ultra-thin heater
Voltage / Frequency 120V / 60Hz
Power Low:800W / High:1500W
Wind speed ≥ 1.3 m/s
Oscillation 76º
Timer 1-12 hours
Noise level ≤50dB（1m distance）
Tip-over Protection 40 ± 10°
Size Φ260*845 mm
Net Weight 4.3 kg
Gross Weight 5.2 kg
4
GENERAL SAFETY
Thank you for purchasing the Ozeri Dual Zone Ceramic Heater and Fan. This product
has passed extensive quality assurance tests for residential use. Every care has been
taken to ensure that it reaches you in perfect condition.
Warning: When using electric appliances, basic safety precautions should be
followed to reduce the risk of re, electric shock and personal injury, including
(but not limited to) the following:
Read all these instructions before attempting to operate this product and save these
instructions for future reference:
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY
MARKINGS IN THIS MANUAL AND ON THE APPLIANCE
When using an electrical appliance, basic precautions should always be followed,
including the following:
WARNING
THE HEATER AND THE REMOTE CONTROL BOTH CONTAIN MAGNETS:
• Pacemakers and debrillators may be affected by strong magnetic elds. If you or
someone in your household has a pacemaker or debrillator, avoid placing the
remote control in a pocket or near the device.
• Credit cards and electronic storage media my also be affected by magnets and
should be kept away from the remote control and the top of the heater.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:
• This heater is hot when in use and for a short period after use. To avoid burns, do
not let bare skin touch hot surfaces. When moving the heater, hold it by the base,
not the air loop amplier.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes
and curtains, at least 3 feet (0.9 m) from the front of the heater and keep them away
from the sides and rear when the heater is plugged in.
• Extreme caution is necessary when any heater is used by or near children or inrm
persons and whenever the heater is left operating and unattended.
• Do not allow to be used as a toy. Close attention is necessary when used by or near
young children. Children should be supervised to ensure that they do not play with
the heater or remote control.
• This heater and remote control are not intended for use by young children or inrm
persons with reduced physical, sensory or reasoning capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
by a responsible person concerning use of the heater to ensure that they can use it
safely.
• The base must be tted securely before operating. Do not dismantle or use without
the base tted.
• Suitable for dry locations ONLY. Do not use outdoors or on wet surfaces. Do not
use in bathrooms, laundry areas and similar indoor locations. Never locate the
heater where it may fall into a bath or other water container. Do not use or store
where it may get wet or in the immediate surroundings of a bath, a shower or a
swimming pool.
• A heater has hot parts inside. Do not use it in areas where gasoline, paint, or
ammable liquids are used or stored or where their vapors are present. Do not use
in conjunction with or directly next to an air freshener or similar product.
• Do not locate directly below a main electricity supply outlet.
• Always plug directly into a wall outlet. Never use with an extension cord or
relocateable power tap (outlet/power strip) as overloading may result in the cord
overheating and catching re.
• Do not handle any part of the plug or heater with wet hands.
• Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.
• Do not stretch the cord or place the cord under strain. Do not run the cord under
carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do
not route the cord under furniture or appliances. To avoid a tripping hazard
arrange the cord away from trac area so that it will not be tripped over.
• Do not use with a damaged cord or plug. If the supply cord is damaged it must be
replaced by an Ozeri service agent or similarly qualied persons in order to avoid
a hazard.
• To disconnect the heater, turn the controls off, then remove the plug from the
outlet. Always unplug the heater when not in use.
• Do not use if the heater malfunctions or has been dropped or damaged in any
manner. Contact the Ozeri Helpline or return to an authorized service facility for
examination and/or repair.
• To prevent a possible re, do not use with any opening or exhaust blocked, and
keep free of dust, lint, hair, and anything that may reduce airow. Do not put any
object into the inlet grill or the exhaust opening as this may cause an electric
shock or re, or damage the heater.
• Do not use on soft surfaces, such as a bed, where openings may become blocked.
• Use only as described in this Ozeri Operating Manual. Any other use not
recommended by the manufacturer may cause re, electric shock, or injury to
persons.
• In order to avoid overheating and re hazard, do not cover the heater.
• Choking hazard: the remote control unit contains a small battery. Keep the remote
control away from children and do not swallow the battery. If the battery is
swallowed, seek medical advice at once.
• Check your heater cord and plug connections. A loose tting outlet can cause the
plug to overheat and/or cause a re. Be sure the plug ts tight in the outlet. Check
frequently during use to make sure plug and outlet are not hot. If so, discontinue
using heater and have outlet replaced by a qualied electrician. Note: Heaters
draw more current than small appliances, overheating of the outlet may occur
even if it has not occurred with the other appliances.
• The heater should be positioned so the airow is directed away from any walls or
room corners.
IMPORTANT SAFETY FEATURES
For your safety this heater is tted with automatic cut-out switches that
operate if the heater tips over or overheats. If the switches operate, unplug the
heater and allow it to cool. Before restarting the heater check and clear any
blockages and ensure the heater is on a solid level surface.
It is normal for the plug to feel warm to the touch; however, if there is a loose t
between the plug and the outlet or the plug becomes very hot, the outlet may need
to be replaced. Check with a qualied electrician to replace the outlet.
READ AND SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY
POLARIZATION INSTRUCTIONS
This heater has a polarized plug (one blade is wider than the other). To reduce the risk
of electric shock, this plug is intended to t in a polarized outlet only one way. If the
plug does not t fully in the outlet, reverse the plug. If it still does not t, contact a
qualied electrician. Do not attempt to defeat this safety feature.
TECHNICAL SPECIFICATIONS
Model OZH1
Name Ultra-thin heater
Voltage / Frequency 120V / 60Hz
Power Low:800W / High:1500W
Wind speed ≥ 1.3 m/s
Oscillation 76º
Timer 1-12 hours
Noise level ≤50dB（1m distance）
Tip-over Protection 40 ± 10°
Size Φ260*845 mm
Net Weight 4.3 kg
Gross Weight 5.2 kg
FEATURES
1. Ultra-thin prole with an elegant glass base that reduces accidental tip-over.
2. Dual PTC ceramic heating system that provides 2 independently controllable
heating zones.
3. Room temperature range from 59°F to 95°F.
4. Intelligent thermostat adjusts output according to the ambient temperature.
5. Winter warming ceramic heating power of 800W (low) / 1500W (high).
6. Summer cooling fan function that provides refreshing air during hot summer
periods.
7. New DC motor generates warming and cooling air with a lower noise coefficient.
8. Touch-button control panel with illuminating LCD and temperature display.
9. Extended range remote control.
10.76° oscillation with a programmable 12 hour timer (for both heater and fan
functions).
11.Low and high speed settings (for both heater and fan functions).
12.Automatic overheat protection for both heating elements.
13.Automatic tip-over safety switch.
14.Dismountable dustproof lters allow for easy cleaning.
15.Easy-carry recessed handle.
16.Height of 85 cm / 33.5 inches.
FEATURES
1. Ultra-thin prole with an elegant glass base that reduces accidental tip-over.
2. Dual PTC ceramic heating system that provides 2 independently controllable
heating zones.
3. Room temperature range from 59°F to 95°F.
4. Intelligent thermostat adjusts output according to the ambient temperature.
5. Winter warming ceramic heating power of 800W (low) / 1500W (high).
6. Summer cooling fan function that provides refreshing air during hot summer
periods.
7. New DC motor generates warming and cooling air with a lower noise coefficient.
COMPONENT LIST
1 Operating Panel 2 LCD Display
3 Power Button 4 Grill
5 Air Outlets 6 Tower Body
7 Back Cover 8 Base Stand
9 Master Power Switch 10 Filter Cover
11 Filter 12 Power Cord
13 Carrying Handle 14 Locking Nut
5
8. Touch-button control panel with illuminating LCD and temperature display.
9. Extended range remote control.
10.76° oscillation with a programmable 12 hour timer (for both heater and fan
functions).
11.Low and high speed settings (for both heater and fan functions).
12.Automatic overheat protection for both heating elements.
13.Automatic tip-over safety switch.
14.Dismountable dustproof lters allow for easy cleaning.
15.Easy-carry recessed handle.
16.Height of 85 cm / 33.5 inches.
The device can also be controlled via the included remote control. The
remote control has 7 buttons that perform the same function as the
main control panel. When using the remote control, point it towards to
the control panel in the middle of the heater.
MAINTENANCE
This devices features 2 removable air lters. The air lters are designed to capture dust
and airborne dirt, and should be inspected and cleaned once a month, or as needed
on a periodic basis. The accumulation of excess dust and dirt in the air lters can nega-
tively affect the performance of this device. Before attempting to clean, always turn
off the device by switching the master switch off on the back of the device rst. Then
unplug the device’s power cord from the wall outlet.
1. Ensure that the above instructions were followed by turning off the fan and
unplugging it from the outlet rst.
2. Wipe the surface and outside of the device by using a damp soft cloth. Do not
immerse in water and never use thinners or other cleaning solutions as these may
damage the fan’s surface appearance.
3. Remove and clean the lter covers rst with a duster and then wipe away any
excess dust with a damp soft cloth. Ensure that the lter covers are completely dry
when nished.
4. Remove the air lters as shown in the following illustration. Clean the air lters by
immersing them in clean water for several minutes. Ensure that the air lters are
allowed to dry completely when nished.
5. Once thoroughly dried, place the cleaned air lters back into the device and
assemble securely with the lter covers, as shown in the illustration below.
5
Unpack the heater and check that you have main heater, the glass base, and remote
control unit. Place the main heater at on the ground (laying on its side) and remove
the locking nut from the bottom end. Connect the glass base onto the bottom, and
secure together with the locking nut.
Note: Ensure the locking nut is rmly secured before standing the heater up on
its base.
REPLACING BATTERY
Your remote control is powered by an included
CR2032 Lithium battery. To replace the battery,
pull out the battery holder and insert a new
battery. Ensure that the polarity is correct and
then insert the battery holder back into the
remote control (Fig 3).
When the heater’s power is on, the remote
control can be used to operate the heater from up
to 20 feet away. Note: if there are two or more
heaters within this distance, both will be
operated by the same remote control. If the
remote control will not be used for a long
period of time, remove the batteries from the
battery compartment.
OPERATING THE HEATER
This heater and fan can be operated via the built-in touch control panel, and via the
remote control device. Before using this device, read through and follow all safety
warnings printed in this manual.
Control Panel Overview:
To use the built-in control panel, rst press the master power switch located behind
the fan towards the bottom (see point 9 on page 5). A deep sound will conrm that
the master switch has been engaged. Then press the power button located at the top
of the device (see point 3 on page 5). The following touch control buttons will illumi-
nate on the control panel:
3
6
The following indicator icons will illuminate immediately above the control panel’s
touch buttons. The indicators icons will activate based on the settings you choose via
the touch buttons.
Continue to press each to cycle through each heater’s off, low and high settings. The
following icons will appear:
Indicates the heater will release air at the low speed setting.
Indicates the heater will release air at the high speed setting.
To activate the heater’s thermostat, press the Temp/Timer icon:
The room temperature display will ash on the screen. Press the press
buttons to set the thermostat to your desired heating temperature. The heater will
remain until it detects the room temperature equals the thermostat temperature.
To activate the fan without the heating element, press the minus to the lowest
possible setting of 59°F, and then press the minus button one more time. The
screen will show the following icon to conrm that it is in fan mode.
For maximum fan performance, ensure the Heater (1) and (2) are set to their high
speed settings.
To activate the fan’s timer, press the press the Temp/Timer icon again:
In timer mode, instead of displaying the temperature, 0 H will ash on the LCD,
indicating zero hours. Press the press buttons to increase or decrease the
timer in units of 1 hour, up to a maximum of 12 hours. The timer will stop ashing to
indicate it is programmed, and keep the heater on until the number of hours chosen
has passed. Note, changing the timer once it has started will reset it.
To engage the heater and fan’s oscillation, press the SWING button on the far
right side of the control panel. The following icon will appear to conrm that
the device is in oscillation mode.
The device can also be controlled via the included remote control. The
remote control has 7 buttons that perform the same function as the
main control panel. When using the remote control, point it towards to
the control panel in the middle of the heater.
MAINTENANCE
This devices features 2 removable air lters. The air lters are designed to capture dust
and airborne dirt, and should be inspected and cleaned once a month, or as needed
on a periodic basis. The accumulation of excess dust and dirt in the air lters can nega-
tively affect the performance of this device. Before attempting to clean, always turn
off the device by switching the master switch off on the back of the device rst. Then
unplug the device’s power cord from the wall outlet.
1. Ensure that the above instructions were followed by turning off the fan and
unplugging it from the outlet rst.
2. Wipe the surface and outside of the device by using a damp soft cloth. Do not
immerse in water and never use thinners or other cleaning solutions as these may
damage the fan’s surface appearance.
3. Remove and clean the lter covers rst with a duster and then wipe away any
excess dust with a damp soft cloth. Ensure that the lter covers are completely dry
when nished.
4. Remove the air lters as shown in the following illustration. Clean the air lters by
immersing them in clean water for several minutes. Ensure that the air lters are
allowed to dry completely when nished.
5. Once thoroughly dried, place the cleaned air lters back into the device and
assemble securely with the lter covers, as shown in the illustration below.
7
Unpack the heater and check that you have main heater, the glass base, and remote
control unit. Place the main heater at on the ground (laying on its side) and remove
the locking nut from the bottom end. Connect the glass base onto the bottom, and
secure together with the locking nut.
Note: Ensure the locking nut is rmly secured before standing the heater up on
its base.
REPLACING BATTERY
Your remote control is powered by an included
CR2032 Lithium battery. To replace the battery,
pull out the battery holder and insert a new
battery. Ensure that the polarity is correct and
then insert the battery holder back into the
remote control (Fig 3).
When the heater’s power is on, the remote
control can be used to operate the heater from up
to 20 feet away. Note: if there are two or more
heaters within this distance, both will be
operated by the same remote control. If the
remote control will not be used for a long
period of time, remove the batteries from the
battery compartment.
OPERATING THE HEATER
This heater and fan can be operated via the built-in touch control panel, and via the
remote control device. Before using this device, read through and follow all safety
warnings printed in this manual.
Control Panel Overview:
To use the built-in control panel, rst press the master power switch located behind
the fan towards the bottom (see point 9 on page 5). A deep sound will conrm that
the master switch has been engaged. Then press the power button located at the top
of the device (see point 3 on page 5). The following touch control buttons will illumi-
nate on the control panel:
The following indicator icons will illuminate immediately above the control panel’s
touch buttons. The indicators icons will activate based on the settings you choose via
the touch buttons.
Continue to press each to cycle through each heater’s off, low and high settings. The
following icons will appear:
Indicates the heater will release air at the low speed setting.
Indicates the heater will release air at the high speed setting.
To activate the heater’s thermostat, press the Temp/Timer icon:
The room temperature display will ash on the screen. Press the press
buttons to set the thermostat to your desired heating temperature. The heater will
remain until it detects the room temperature equals the thermostat temperature.
To activate the fan without the heating element, press the minus to the lowest
possible setting of 59°F, and then press the minus button one more time. The
screen will show the following icon to conrm that it is in fan mode.
For maximum fan performance, ensure the Heater (1) and (2) are set to their high
speed settings.
To activate the fan’s timer, press the press the Temp/Timer icon again:
In timer mode, instead of displaying the temperature, 0 H will ash on the LCD,
indicating zero hours. Press the press buttons to increase or decrease the
timer in units of 1 hour, up to a maximum of 12 hours. The timer will stop ashing to
indicate it is programmed, and keep the heater on until the number of hours chosen
has passed. Note, changing the timer once it has started will reset it.
To engage the heater and fan’s oscillation, press the SWING button on the far
right side of the control panel. The following icon will appear to conrm that
the device is in oscillation mode.
Indicator Icon Overview:
Indicator Icon Functions:
The device can also be controlled via the included remote control. The
remote control has 7 buttons that perform the same function as the
main control panel. When using the remote control, point it towards to
the control panel in the middle of the heater.
MAINTENANCE
This devices features 2 removable air lters. The air lters are designed to capture dust
and airborne dirt, and should be inspected and cleaned once a month, or as needed
on a periodic basis. The accumulation of excess dust and dirt in the air lters can nega-
tively affect the performance of this device. Before attempting to clean, always turn
off the device by switching the master switch off on the back of the device rst. Then
unplug the device’s power cord from the wall outlet.
1. Ensure that the above instructions were followed by turning off the fan and
unplugging it from the outlet rst.
2. Wipe the surface and outside of the device by using a damp soft cloth. Do not
immerse in water and never use thinners or other cleaning solutions as these may
damage the fan’s surface appearance.
3. Remove and clean the lter covers rst with a duster and then wipe away any
excess dust with a damp soft cloth. Ensure that the lter covers are completely dry
when nished.
4. Remove the air lters as shown in the following illustration. Clean the air lters by
immersing them in clean water for several minutes. Ensure that the air lters are
allowed to dry completely when nished.
5. Once thoroughly dried, place the cleaned air lters back into the device and
assemble securely with the lter covers, as shown in the illustration below.
Unpack the heater and check that you have main heater, the glass base, and remote
control unit. Place the main heater at on the ground (laying on its side) and remove
the locking nut from the bottom end. Connect the glass base onto the bottom, and
secure together with the locking nut.
Note: Ensure the locking nut is rmly secured before standing the heater up on
its base.
REPLACING BATTERY
Your remote control is powered by an included
CR2032 Lithium battery. To replace the battery,
pull out the battery holder and insert a new
battery. Ensure that the polarity is correct and
then insert the battery holder back into the
remote control (Fig 3).
When the heater’s power is on, the remote
control can be used to operate the heater from up
to 20 feet away. Note: if there are two or more
heaters within this distance, both will be
operated by the same remote control. If the
remote control will not be used for a long
period of time, remove the batteries from the
battery compartment.
OPERATING THE HEATER
This heater and fan can be operated via the built-in touch control panel, and via the
remote control device. Before using this device, read through and follow all safety
warnings printed in this manual.
Control Panel Overview:
To use the built-in control panel, rst press the master power switch located behind
the fan towards the bottom (see point 9 on page 5). A deep sound will conrm that
the master switch has been engaged. Then press the power button located at the top
of the device (see point 3 on page 5). The following touch control buttons will illumi-
nate on the control panel:
The following indicator icons will illuminate immediately above the control panel’s
touch buttons. The indicators icons will activate based on the settings you choose via
the touch buttons.
Using the control panel’s buttons, press Heater (1) to turn on the top heater, and
Heater (2) to turn on the bottom heater.
Continue to press each to cycle through each heater’s off, low and high settings. The
following icons will appear:
Indicates the heater will release air at the low speed setting.
Indicates the heater will release air at the high speed setting.
To activate the heater’s thermostat, press the Temp/Timer icon:
The room temperature display will ash on the screen. Press the press
buttons to set the thermostat to your desired heating temperature. The heater will
remain until it detects the room temperature equals the thermostat temperature.
To activate the fan without the heating element, press the minus to the lowest
possible setting of 59°F, and then press the minus button one more time. The
screen will show the following icon to conrm that it is in fan mode.
For maximum fan performance, ensure the Heater (1) and (2) are set to their high
speed settings.
To activate the fan’s timer, press the press the Temp/Timer icon again:
In timer mode, instead of displaying the temperature, 0 H will ash on the LCD,
indicating zero hours. Press the press buttons to increase or decrease the
timer in units of 1 hour, up to a maximum of 12 hours. The timer will stop ashing to
indicate it is programmed, and keep the heater on until the number of hours chosen
has passed. Note, changing the timer once it has started will reset it.
To engage the heater and fan’s oscillation, press the SWING button on the far
right side of the control panel. The following icon will appear to conrm that
the device is in oscillation mode.
8
The device can also be controlled via the included remote control. The
remote control has 7 buttons that perform the same function as the
main control panel. When using the remote control, point it towards to
the control panel in the middle of the heater.
MAINTENANCE
This devices features 2 removable air lters. The air lters are designed to capture dust
and airborne dirt, and should be inspected and cleaned once a month, or as needed
on a periodic basis. The accumulation of excess dust and dirt in the air lters can nega-
tively affect the performance of this device. Before attempting to clean, always turn
off the device by switching the master switch off on the back of the device rst. Then
unplug the device’s power cord from the wall outlet.
1. Ensure that the above instructions were followed by turning off the fan and
unplugging it from the outlet rst.
2. Wipe the surface and outside of the device by using a damp soft cloth. Do not
immerse in water and never use thinners or other cleaning solutions as these may
damage the fan’s surface appearance.
3. Remove and clean the lter covers rst with a duster and then wipe away any
excess dust with a damp soft cloth. Ensure that the lter covers are completely dry
when nished.
4. Remove the air lters as shown in the following illustration. Clean the air lters by
immersing them in clean water for several minutes. Ensure that the air lters are
allowed to dry completely when nished.
5. Once thoroughly dried, place the cleaned air lters back into the device and
assemble securely with the lter covers, as shown in the illustration below.
9
Unpack the heater and check that you have main heater, the glass base, and remote
control unit. Place the main heater at on the ground (laying on its side) and remove
the locking nut from the bottom end. Connect the glass base onto the bottom, and
secure together with the locking nut.
Note: Ensure the locking nut is rmly secured before standing the heater up on
its base.
REPLACING BATTERY
Your remote control is powered by an included
CR2032 Lithium battery. To replace the battery,
pull out the battery holder and insert a new
battery. Ensure that the polarity is correct and
then insert the battery holder back into the
remote control (Fig 3).
When the heater’s power is on, the remote
control can be used to operate the heater from up
to 20 feet away. Note: if there are two or more
heaters within this distance, both will be
operated by the same remote control. If the
remote control will not be used for a long
period of time, remove the batteries from the
battery compartment.
OPERATING THE HEATER
This heater and fan can be operated via the built-in touch control panel, and via the
remote control device. Before using this device, read through and follow all safety
warnings printed in this manual.
Control Panel Overview:
To use the built-in control panel, rst press the master power switch located behind
the fan towards the bottom (see point 9 on page 5). A deep sound will conrm that
the master switch has been engaged. Then press the power button located at the top
of the device (see point 3 on page 5). The following touch control buttons will illumi-
nate on the control panel:
The following indicator icons will illuminate immediately above the control panel’s
touch buttons. The indicators icons will activate based on the settings you choose via
the touch buttons.
Continue to press each to cycle through each heater’s off, low and high settings. The
following icons will appear:
Indicates the heater will release air at the low speed setting.
Indicates the heater will release air at the high speed setting.
To activate the heater’s thermostat, press the Temp/Timer icon:
The room temperature display will ash on the screen. Press the press
buttons to set the thermostat to your desired heating temperature. The heater will
remain until it detects the room temperature equals the thermostat temperature.
To activate the fan without the heating element, press the minus to the lowest
possible setting of 59°F, and then press the minus button one more time. The
screen will show the following icon to conrm that it is in fan mode.
For maximum fan performance, ensure the Heater (1) and (2) are set to their high
speed settings.
To activate the fan’s timer, press the press the Temp/Timer icon again:
In timer mode, instead of displaying the temperature, 0 H will ash on the LCD,
indicating zero hours. Press the press buttons to increase or decrease the
timer in units of 1 hour, up to a maximum of 12 hours. The timer will stop ashing to
indicate it is programmed, and keep the heater on until the number of hours chosen
has passed. Note, changing the timer once it has started will reset it.
To engage the heater and fan’s oscillation, press the SWING button on the far
right side of the control panel. The following icon will appear to conrm that
the device is in oscillation mode.
WARRANTY INFORMATION
Your Ozeri product is warranted to the original owner for 1 year from the date
of purchase against defects in material and workmanship under normal use
and service. Should your Ozeri product prove defective within 1 year from the
date of purchase, return the defective product, freight prepaid along with your
receipt and an explanation of the claim to “Ozeri.” Please pack your Ozeri
product carefully to avoid damages in transit. Under this warranty, Ozeri will
repair or replace any parts found to be defective due to a manufacturer’s
defect. This warranty extends only to personal use and does not extend to any
product that has been used for commercial use, rental use, or use which is not
intended. There are no warranties other than that expressly set forth herein.
This warranty is not transferable. Ozeri is not responsible in any way for
damages, losses or inconveniences caused by equipment failure or by user
negligence, abuse, or use not in accordance with the “User Guide” or any
additional safety, use, or warnings included in the product materials. Further,
Ozeri is not liable for incidental or consequential damages of any nature
resulting from the use of this product and any liability shall not exceed the
purchase price of the product.
This Warranty gives you specic legal rights. You may also have other rights
which vary from state to state.
THIS WARRANTY DOES NOT APPLY TO THE FOLLOWING
- Damage due to accident, misuse, abuse, alterations or vandalism.
- Improper or inadequate maintenance.
- Unauthorized modication or commercial use.
- Damage in return transit
- Unsupervised use by children
Ozeri Customer Service:
Phone: 1-877-299-1296
Email: suppor[email protected]om
(OzeriTM and its subsidiaries assume no liability for damage caused by the use
of this product other than for its intended use or as instructed above and in the
User Manual.)
Table of contents
