Ozoneair GO User manual

GO

GO
USER MANUAL
Ozoneair GO
ENGLISH |DEUTSCH |ESPAÑOL |SVENSKA |DANISH |SUOMI |NORWEGIAN

Introduction
Safety notices
Users responsibility
Safetey guidelines
Before use
During use
After use
Description & specifications
Certifications
Operating requirements
Technical details
Parts
Display
Automatic mode
Treatment time & space
Recommendations
Manual mode
Continues mode
Day-Timer mode
Troubleshooting
Warranty terms
Product warranty
Consumables warranty
01
02
03
04
05
06
07
08
09
5
5
5
6
6
6
6
7
7
7
7
9
10
11
12
12
12
13
13
14
15
15
15
TABLE OF CONTENT
EN 5

In this instruction manual, the following symbols are used to indicate
specific risk situations, precautions and procedures that should be noted.
WARNING! - This symbol indicates a warning and should be
followed to avoid personal injury and property damage.
CAUTION - This symbol indicates precautions that should be
taken to ensure proper use of your product.
NOTE - This symbol indicates special instructions or tips that will
help you get the most out of your product.
Safety notices
User responsibility
This instruction manual is intended to help
you use your Ozoneair safer and to provide
information about the use and maintenance
of the product. Please read the operating
instructions carefully before using the product for
the first time.
If you after reading the instruction manual, still
are not sure that you understand the security risks
that may be associated with the product, do not
use it. Contact your dealer for further information.
These safety instructions only summarize
the basics for safe use. It is not in the safety
instructions possible to describe all possible risk
situation that may arise when using the product.
However, you can prevent accidents by always
using common sense.
INTRODUCTION
01
It is the user’s responsibility to comply with all recommendations and
safety instructions before using the product.
WARNING! - Do not use in areas where people, plants
or animals are located. Ozone can cause irritation of the
eyes, throat and nose during prolonged exposure.
7
EN

• Make sure that no one is entering the space during treatment.
• Ensure that ozone does not leak to nearby areas where plants, animals
and humans are present while the treatment is in progress.
The time before a space can be entered after treatment is two hours.
If the space needs to be entered more quickly, ventilate properly and
make sure all ozone is gone.
• Ensure that no plants, animals or humans are present in the area
before treatment begins.
• Close and seal the space to avoid leakage of ozone to nearby areas
where plants, animals and humans are located.
• Make sure the product is set to match the size of the area being
treated. See “Auto Mode”
During use
After use
Before use
When using the product, certain safety
precautions must be followed to reduce the risk
of personal injury or property damage.
SAFETY GUIDELINES
02
WARNING! - Always pay attention to any ozone-re-
lated symptoms such as irritation of the eyes, throat
and nose. Leave the space if any symptoms appear
and let the ozone completely disappear.
WARNING! – Incorrect setting of the product may
cause permanent damage to property.
NOTE – Use the included door hanger to prevent peo-
ple from entering the area during ongoing treatment.
8
Ozoneair uses corona discharge to convert
oxygen (O2) to ozone (O3). When used correctly,
it can permanently oxidize organic compounds
(odorants, bacteria, mold, virus, etc.) at the
molecular level.
DESCRIPTION & SPECIFICATIONS
03
Operating temperature:
Relative humidity:
Operating altitude:
0 °C till 35 °C
5 % till 95 % (noncondensing)
tested up to 5 000 meters
Operating requirements
CE - Ozoneair are CE marked and comply with the RED
Directive (2014/53/ EU), the EMC Directive (2014/30/
EU), and the Low Voltage Directive (2014/35/EU) issued
by the European Commission.
RoHS – Ozoneair complies with the RoHS Directive
(2002/95 / EC) which prohibits the use of hazardous
substances in electronic equipment.
Certifications
Technical details
9
Model:
Line voltage/Frequency:
Eect:
Height:
Width:
Depth:
Weight:
GO
220-240 V/50-60 Hz
60 W
25,0 cm
15,5 cm
24,0 cm
2,9 kg
ENEN

10
1. Air outlet 2. Air intake 3. Screen interface 4. Handle 5. Power source 6. Feets
FRONT BACK BOTTOM
PARTS
04
11
3
1
5
4
2
6
ENEN

DISPLAY
05
12
AUTO
MANU
CONT REPLACE PLATE
SQM
LEAVE
AREA
DAILY
CYCLE
%
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
MODE TIME START/STOP
5
2 3 4
1. Selector knob 2. Mode button 3. Timer button 4. Start /stop button 5. LED screen
Come back after
treatment time
plus two hours.
MODE TIME START/STOP
4
Connect power
cable to product
and then to a
power outlet.
Press and then
turn the knob to
adjust the size of
the space.
Appropriate
treatment time
is shown on the
display.
3
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
AUTOMATIC MODE
06
13
1
5
6
2h
Product starts
beeping. Leave the
area.
Press start button
to active the
product.
2
ENEN
1
6 Hr
8 Hr
12 Hr

14
Press time to select
time.
Press “mode” once
to activate.
Press “start/stop”
to start
Turn knob to select
the eect.
MANUAL MODE
07
2
3
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
1
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
4
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
In automatic mode, treatment time is automatically adjusted for best
eect. If a shorter period is preferred, the size of space can be reduced
by turning the knob until a suitable time is displayed.
Treatment time & space
• Treatments at higher temperatures give better eect as the pores
in the materials open and allow the ozone to penetrate better. Ideal
temperatures are 20 ° C or higher.
• Place the product as centrally as possible in the space.
• Place products high, for example, on a table or chair.
• When treating small spaces or vehicles, open the windows and
ventilation slightly.
• Open the space that is being treated so that the surfaces can be
exposed to the ozone (wardrobes, cabinets etc.)
Recommendations
CAUTION -The area and thus the treatment time
are calculated at 2.5 m ceiling height. If a room with a
lower ceiling height is treated, the surface should be ad-
justed accordingly. For example, if the ceiling height is
only 1.25 m, then the surface should be adjusted to half.
15
Press “time” to
select daily cycles.
Press “start/stop”
to start
Press “mode” twice
to activate.
Press button
‘Mode’ twice to
activate.
Press “start/stop”
to start
Turn knob to select
the eect.
Turn knob to select
the eect. 22
Continues mode Day-Timer mode
3
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
1
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
4
3
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
MODE TIME START/STOP
AUTO
MANU
CONT
1 Hr
2 Hr
4 Hr
6 Hr
8 Hr
12 Hr
1
ENEN

16
TROUBLESHOOTING
08
Problem Possible reason Solution
Product not starting Power cord not properly connected.
Fuse has gone.
Check so that power cord is properly
connected.
Replace the fuse.
Wait for the delay function to disable.
Display doesn’t light up Product has not been activated. Press knob to activate.
Clean the oxygen plates.
Replace the oxygen plates
Delay function is active.
Oxygen plates are dirty.
Oxygen plates are consumed.
Unit start but produce less ozone
Unit starts but produce no ozone
17
* This warranty applies only to products that have not been subjected
to negligent use, abuse, other applications than those specified in the
operating instructions, modifications, accidents, use of unauthorized
parts, failure to perform periodic maintenance as specified in the
operating instructions, normal wear or repairs as Not carried out by
an authorized repairer. There is no other express warranty. All other
warranties are excluded. Liability for damage or consequential damages
is excluded in so far as exemptions are permitted by law.
WARRANTY TERMS
Product warranty
Consumables warranty
Ozoneair warrants that this product will be free of defects in material
and / or manufacturing defects for a period not exceeding 5 years from
the date of purchase of its original buyer. Ozoneair undertakes to provide
spare parts free of charge within this period and only charge reasonable
labour costs to correct the error. Material and/or manufacturing defects
will be remedied by repair or replacement of a new product free of
charge for the original buyer within a period of 2 years from the date of
purchase. This warranty applies to the original owner who provides proof
of purchase. The guarantee cannot be transferred. The warranty period
will start on the date of purchase.
Ozoneair ensures that the oxygen plates will be free of defects in material
and/or manufacturing defects for a period not exceeding 90 days or 500
operating hours (whichever occurs first) from the date of purchase of the
original buyer.
NOTE– If the product cover is opened, all warranties will
expire. No repairable parts are inside.
09
ENEN

GO
USER MANUAL
Ozoneair GO
ENGLISH |DEUTSCH |ESPAÑOL |SVENSKA |DANISH |SUOMI |NORWEGIAN