OzSpy DSA055UEMR User manual

ABOUT BATTERY
1. When the Battery Low LED lights up, power is low. Please
replace the batteries.
2. When not in use we recommend removing the batteries to avoid battery
leakage which may damage the circuit board.
NOTICE OF USE
1. If you are not going to use this device for a long time, remove the batteries to avoid
damage caused by corrosion from battery leakage.
2. Unauthorized repair or disassembly of this device will void all the warranties.
3. Avoid water.
4. Do not store this device in an excessively hot place.
5. Avoid knocks or dropping this device.
6. Never use the antenna of this device to touch a metal surface or the antenna of
signal emission source. The warranty does not cover any damage caused by static
electricity or feedback.
SPECIFICATION * Specification may change without notice.
Detecting range
50 MHz ~ 6.0 GHz
Detect object
1. Wireless and wired camera, Micro SD hidden camera
2. Wireless RF devices
3. Operating and standby cell phones
4. Magnet of GPS tracker
Dimension
L 10.4 x W 5.5 x T 2.2 cm
Weight
About 75g (not include battery)
Power
AAA/ UM-4 dry battery x 3
Warning mode
Vibration
Sensitivity Tuner
1. Adjust detecting distance to find signal source
2. Eliminate the environment interference
Detecting Distance
100mW 2.4GHz Wireless camera
up to 20 feet
10mW 5.8GHz Wireless camera
up to 3 feet
GSM Cell phone
up to 40 feet
Smartphone
up to 10 feet
3G 2100 cell network
up to 2 feet
* The detecting distance will be varied depending on the signal strength.
WARNING Use this device as an auxiliary, supplemental help or aid to prevent the risks caused by hidden camera,
cellular phone or other wireless devices. This device does not take the place of all the supervisions. Performance of this Radio
frequency (RF) product will be affected by the circumstance of use. The producer and marketing group accepts no liability for any loss
or damage by malfunction or misuse.
COPYRIGHT All rights reserved
©Copyright 2019, All rights reserved. Made in Taiwan
06.2019
DSA055UEMR
User Manual
All-in-one Hidden Camera Detector
Thank you for purchasing this Hi-tech device. Please read the
manual prior to use and save for future reference.
BATTERY INSTALLATION
Remove the battery cover, install 3 x AAA batteries according
to the + –indication. This device will also support
rechargeable batteries.
The power switch is located on the left side. Set at 1 to
switch on, set at 0 to switch off.
SMART INDICATION OF ALL STATUS
No.
NAME
DESCRIPTION
1
RF Signal
RF signal detection (Default)
2
EMR Finder
Micro SD hidden camera detection
3
Lens Finder
Discover camera lens
4
Magnet Finder
Discover magnet of GPS tracker
5
WiFi / Digital
WiFi signal and Digital signal
6
CAM / Bug / LTE
Analog and Spread spectrum signal of
Camera, bug and cellphone
7
Battery low
Battery power running low
1
.
2
.
3
.
6
.
5
.
4
.
7
.

POWER-ON SELF-TEST
Every time this device is switched on, it will perform a power-on self-test of all
functions and all the LEDs will light up (excludes Bat. low). The 8 signal
strength indication LEDs will then go out one-by-one, 8 7 6 etc… to 0.
8-LED SIGNAL STRENGTH INDICATION
The 8-LED bar will light up according to the signal
strength from low to high, green →yellow →red, stronger
signal, more LED.
HOW TO OPERATE
1. Pull out the antenna and turn on the device. The device will do power-on
self-test and then the Power and “RF Signal”LED will light up.
2. If more than one strength indication LED lights up and is vibrating, it means
that there is wireless device operating in range.
3. Refer to the chapter of “How to find (locate) the signal source”to find the
position of signal source.
4. This device will indicate the detected signal type.
WiFi / Digital: Signals of WiFi, IP camera, wireless digital
camera and other signal of digital wireless devices.
CAM / BUG / LTE : Analog and Spread spectrum signals of wireless camera,
wireless bug, signal jammer and 2G / 3G / 4G cell phones, etc.
5. This device has 4 functions selected by the
“Function switch”in the bottom of font view.
1
RF
Signal
2
EMR
Finder
3
Lens
Finder
4
Magnet
Finder
6. Default function is “RF Signal”, press the function switch
once, this device will shift to EMR Finder which can detect
the electromagnetic radiation from Micro SD hidden
cameras.
7. Facing the “Detection area” (rear side of the device) towards the suspicious
object, the device will vibrate if the detect the hidden camera is
switch On.
8. Press the function switch once, the device will shift to Lens
Finder. The 6 ultra-bright lights in rear side will blink, scan
towards the suspicious object. This will help find the location of
the wired camera by the reflection of the illuminated light on the camera lens.
Look through the Viewfinder in Lens finder mode, to locate the camera lens.
The lens finder can locate a hidden wireless camera even if the camera is
turned off.
9. Press the function switch once, the device will shift to
Magnet Finder which has a magnet sensor to help users
find a GPS tracker attached to the car using a magnet.
The magnet sensor is located on the left upper side of
the device, from the rear view. Facing the yellow mark area to suspicious
location. The device will vibrate if it detects a strong magnet.
10. Press the function switch once, this device will return to RF signal.
HOW TO FIND (LOCATE) THE SIGNAL SOURCE
1. Hold the device so the front side is facing the user and keep the antenna
upward.
2. Hold the device and scan around to detect a signal. Move forward
one step towards the strongest signal direction. When the 8-LED
signal strength indication is all lit up and the scan range (angle) is
over 120 degree, press once the –(minus) button in left side of the
device, to lower down the sensitivity one level.
The scan angle will lower. Again, scan around to detect a signal and move
forward one step towards the strongest signal direction.
3. Repeat the above step, until you find the signal source. If you lose the signal,
press the + (plus) button to raise the sensitivity until the signal returns and
continue with the detection.
4. The sensitivity has 6 levels, default is highest sensitivity. When adjusted to
the lowest or highest sensitivity, the device will vibrate 3 times to alert the
user.
SEMI DIRECTIONAL ANTENNA
The device has a semi directional feature. When reducing the sensitivity
approaching the signal source, the scan angle will change from wide to narrow,
120 degree →90 degree …45 degree. This feature is very helpful in locating the
signal source.
AIRPLANE MODE SMARTPHONE DETECTION
Set at “EMR Finder”, the device can detect smartphones in airplane
mode by the electromagnetic radiation.