OZTENT RS-1 User manual

OSR01SWLUB
OWNER’S MANUAL

Page 1 of 14
HELPFUL HINT
We recommend that you familiarise yourself
with this product before you leave for your
trip. Check that all parts are present and
that you familiarise yourself with the setup
and pack down of the product.
© Oztent Australia Pty Ltd 11/9/2020 - All rights reserved
Oztent Australia Pty Ltd
www.oztent.com
Document No: OZ0001
Prepared by: Michael Champ
Authorised by: Trent Fitzgibbins
Issue No. 0001
Issue date: 11/9/2020

Page 2 of 14
RS-1 King Single Swag Owner’s Manual
Congratulations and thank you for choosing your
new Oztent product.
We are sure that you will find your new Oztent product a pleasure to use and enjoy.
Before set-up or use, we recommend that you read through this entire manual. It
provides full user instructions.
To avoid any problems that may occur when you use a new product for the first time,
it is important that the Oztent product is set up correctly. Please ensure that you read
all instructions contained in this manual carefully. We want you to have a safe and
enjoyable experience.
After unpacking your new Oztent product, please check that it is not damaged and
that all parts have been supplied. If in doubt, contact your local Oztent Customer Care
Centre or dealer.
Don’t like reading instructions?
Scan the QR code below to
watch the how-to video

Page 3 of 14
Contents
Package Contents ......................................................................................................................................... 3
Warning & Important Information ......................................................................................................... 4
Safety and Care............................................................................................................................................5
Setting Up the Oztent RS-1 ........................................................................................................................7
Setting up the awning................................................................................................................................9
Parts Identification..................................................................................................................................... 10
Warranty ...........................................................................................................................................................11
Package Contents
Item General Part Name Qty
1 RS-1 King Single Swag 1
2 Adjustable Awning Poles 2
3 Pegs 17
4 Attached Guy Ropes 4
5 Awning Guy Ropes 2
6 Peg Bag 1
7 Pole Bag 1
8 Carry Bag 1

Page 4 of 14
RS-1 King Single Swag Owner’s Manual
Important Information
Environmental Tips
Packaging disposal
• Most of the packaging materials are recyclable. Please dispose of packaging
materials through your local recycling depot or by placing them in the
appropriate recycling bins.
• If you wish to discard this product, please contact your local authorities and ask
them for the correct method of disposal.
Cautions
• This product is not intended for use by young children or infirmed persons
without supervision.
• Young children should be supervised so that they do not play with the product.
• Contact an authorised service technician for repair or maintenance of this
product.
• Installation work must be performed in accordance with any local, state and
national Standards.
Warning
Never use any fuel-burning products (stoves, lanterns, heaters, etc.) inside or
within proximity of this product. Use of fuel-burning inside or within proximity
of this product can result in the accumulation of dangerous concentrations of
carbon monoxide - a colourless, odourless gas. Breathing carbon monoxide
will cause serious injury or death. Avoid spraying this product with deodorant
or other aerosols as it may destroy the waterproofing.
Keep all flame and heat sources away from this product. This product is
made with flame resistant fabric but it is not fireproof. The product fabric will
burn if left in continuous contact with an open flame or other heat source.
Failure to keep all flame and heat sources away from this product can result in
a fire that can burn.
Before using this product, read and fully understand: 1) attached warnings; 2)
the instruction manual and all accompanying documentation. Failure to follow
these directions can cause an unsafe situation leading to injury.

Page 5 of 14
Set-up your swag
It is important that you set up your swag when it’s new and also after long periods of
storage. This ensures that you are familiar with the set-up process and ensures that all
frames, poles and pegs are present and still working correctly.
If cared for correctly, your Swag will still be around for the next generation of campers
to enjoy.
Ventilation
Maintain adequate ventilation inside the Swag at all times.
Campsite Choice
When choosing a campsite, carefully consider the possibility of falling rocks or tree
limbs, lightning, flash floods, avalanches, strong winds, and other potential hazards to
reduce the risk of loss or in-jury.
Select a site that’s level, well drained, and is protected from the wind and other
elements. Clear the campsite of sharp stones, sticks, and other debris, both for comfort
and to protect the floor of the Swag. If possible, avoid setting the Swag on ground that
is already wet. If this is not possible keep the Swag well ventilated to minimize humidity
and condensation within the Swag.
Pegs and Ropes
Peg down the Swag properly at all times to reduce the risk of loss or injury to Swag
users.
All Swags require pegging to prevent them from being blown away in strong winds.
Always anchor the Swag. Tent pegs and ropes are supplied to safely setup the Swag in
most situations. It may be necessary to purchase additional and/or specialized pegs and
ropes for use in extreme or varied soil conditions.
Tightly tensioning the Swag with attached ropes greatly increases the Swag’s strength
and stability. This will also reduce fabric sagging and wrinkles and prevent rainwater
from pooling.
Condensation
When warm, moist air comes in contact with the cool Swag fabric condensation can
form. In most situations condensation can be controlled by allowing air inside the Swag
to vent outside. During periods of high humidity, such as during rain storms, it may be
dicult to prevent or reduce condensation. In these situations ventilation could actually
increase the condensation by drawing in more humid air.
Condensation can also collect on parts of the floor inside the Swag. This is also normal
and does not indicate leaking fabric.
Safety and Care Considerations

Page 6 of 14
RS-1 King Single Swag Owner’s Manual
Zippers
Be careful when using Swag zippers. Go slow when zipping.
Make sure to align the zipper tracks before sliding the zipper and don’t exert excessive
force on the zipper. If the fabric gets caught in the zipper, stop and slowly reverse the
zipper to remove. A silicone based lubricant may be used to improve zipping.
When dirt gets in the zipper teeth, it can cause abrasion and damage to the zipper
sliders. You can clean the zipper teeth by rinsing them with water. The pressure from a
regular garden hose will push out small sand particles.
Cleaning
If the Swag should require cleaning, set it up and use a sponge with warm water
to clean. If further cleaning is required, a garden hose can be used to wash o any
remaining dirt. Do not use detergent, soap, bleach, or have the Swag dry cleaned, as
this may remove the waterproofing and/or damage the fabric. Allow the Swag to air-dry
completely before packing or storing.
Storage
Packing and storing the Swag while it’s wet or damp leads to pre-mature breakdown of
the Swag fabrics and coatings.
Prolonged exposure to moisture causes the waterproof layer to break down, becoming
soft, sticky and no longer waterproof.
Storing a wet Swag can cause mildew to form on the fabric.
Mildew will cause the Swag to stain, smell, and may lead to the premature breakdown of
the waterproof coating. Dry the swag thoroughly after each use.
Animals and Insects
To prevent damage from animals chewing holes in the Swag fabric, never store food or
cooking equipment in the Swag.
When packing away ensure that there are no insects inside the Swag as they may try to
eat their way out causing holes in the material.
Important Notes
Pack the Swag away in the reverse order of set up. Roll up the rear window and front
awning and leave the front door open. Remove all pegs/stakes.
1. You will find on your Swag A and B that this is marked on the panels. Lower the
Swag to the ground and swing in arm “A” followed by arm “B”. Always swing the
arms low to the ground.
2. The Oztent RS-1 King Single Swag is designed for one person operation.
3. The following illustrations are artistic representations of the Oztent RS-1 King Single
Swag and may vary from the production model. However, the overall operation will
be the same.

Page 7 of 14
Setting up the Oztent RS-1
Step 1:
Take the Swag out of the bag. Place the poles and pegs away from the Swag space.
Step 2:
Swing out both arms one at a time.

Page 8 of 14
RS-1 King Single Swag Owner’s Manual
Setting up the Oztent RS-1
Step 3:
Pull the Swag up using the swing tab found near the top frame
Step 4:
Reach inside the Swag and lock the sliding/bracing arms in place, by pushing them up.
It is recommended that the Velcro loop below the sliding/bracing arm hinge to be secured. This will
eliminate the possibility of the Swag accidentally folding down.

Page 9 of 14
Setting up the awning
Step 7:
Unroll the Awning. Twist to unlock awning poles and twist again to lock at desired height. Attach poles to
the Awning and secure with guy ropes.
Setting up the Oztent RS-1
Step 5:
Adjust the Swag so it sits properly. Hammer in all pegs. Peg out guy ropes at 45 degree angle to
secure the swag.
Step 6:
Place the RS-1 Swag mattress inside the Swag. Position it within the frame at the base of the Swag.
OPTIONAL: Lower one pole during heavy rain

Page 10 of 14
RS-1 King Single Swag Owner’s Manual
Parts Identification
Item General Part Name Qty Part No.
1 Main Extrusion 1 OZME
2 Hinge 6 OZH
3 Corner 6 OZC
4 Foot fitting 4 OZFF
5 Foot 2 OZF
6 M8 Nut, Washer and Slider 2 OZS
7 Brace Extrusion with Fittings 4 RS1SA

Page 11 of 14
Warranty
FOR SALES IN AUSTRALIA, USA AND INTERNATIONAL MARKETS.
TENTS, FURNITURE AND ACCESSORIES: [OZTENT, MALAMOO,
AND FOXWING]
This document sets out the terms and conditions of product
warranties for Oztent, Malamoo and Foxwing branded products. It is
an important document. Please keep it with your proof of purchase
documents in a safe place for future reference should you require
service for your Oztent, Malamoo, or Foxwing branded product.
General Terms and Conditions
1. In this warranty
(a) ‘Oztent’ means Oztent Australia Pty Limited ABN 19 050
035 964 in respect of products purchased in Australia,
USA and International markets;
(b) ‘Product’ means any Oztent product purchased by you
accompanied by this document;
(c) ‘Warranty Period’ means
(i) where you use the Product for personal, domestic
or household purposes in Australia the period of ‘12’
months and in USA and International markets the
period of ‘12’ months;
(ii) for Tents and Tent Accessories used for personal,
domestic or household purposes (e.g. Peaked Side
Panel) the period of ‘24’ months;
(iii) for Furniture (e.g. Chairs) and Furniture Accessories
used for personal, domestic or household purposes
the period of ‘60’ months;
following the date of original purchase of the Product;
(d) ‘you’ means the purchaser of the Product not having
purchased the appliance for re-sale, and ‘your’ has a
corresponding meaning.
2. This warranty only applies to Products purchased and used
in Australia, USA or International markets and is in addition
to (and does not exclude, restrict, or modify in any way)
any non-excludable statutory warranties in Australia, USA or
International markets.
3. Oztent warrants that, when dispatched from an Oztent
warehouse, the Product is free from defects in materials and
workmanship for the Warranty Period.
4. During the Warranty Period Oztent or its Authorised Service
Centre will, at no extra charge if your product is readily
accessible without special equipment, and subject to these
terms and conditions, repair or replace any parts which it
considers to be defective. You agree that any replaced Product
or parts become the property of Oztent. This warranty does not
apply to guy ropes, tent pegs, or similar perishable parts.
5. Parts and Products not supplied by Oztent are not covered by
this warranty.
6. Where you are within an Oztent service area, this warranty
covers the cost of transport of the Product only to and from
Authorised Service Centres of Oztent (“ASC”) and travelling
costs for representatives of the ASC to and from your home
or business. If you are outside an Oztent service area, or you
are claiming for an accessory you will bear these costs. For
information about whether you are within an Oztent service
area, or information on your nearest ASC please phone 1800
OZTENT or 1800 698368 in Australia, +8555 OZTENT or
[phone] in the USA or [phone] in International
markets.
7. Proof of purchase is required before you can make a claim
under this warranty.
8. You may not make a claim under this warranty unless the defect
claimed is due to faulty or defective parts or workmanship.
Oztent is not liable in the following situations (which are not
exhaustive):
(a) The Product is damaged by:
(i) accident
(ii) misuse or abuse, including failure to properly
maintain or service
(iii) normal wear and tear
(iv) storm damage or improper storage
(v) incomplete or improper installation
(vi) incorrect, improper or inappropriate operation
(vii) insect or vermin infestation.
(b) The Product is modified without authority from Oztent
in writing.
(c) The Products model number, serial number or warranty
seal has been removed or defaced.
(d) The Product was serviced or repaired by anyone other
than Oztent or its Authorised Service Centres.
9. This warranty, the contract to which it relates and the relationship
between you and Oztent are governed by the law applicable in
the Australian State where the Product was purchased or the
law applicable in the USA or International markets if the Product
was purchased in the USA or International markets. Where the
Product was purchased in the USA or International markets for
business purposes the Consumer Guarantee Act does not apply.
Limitation of Liability
10. To the extent permitted by law:
(a) Oztent excludes all warranties other than as contained in
this document;
(b) Oztent shall not be liable for any loss or damage whether
direct or indirect or consequential arising from your
purchase, use or non-use of the Product.
11. Provisions of the Trade Practices Act and State consumer
legislation in Australia, and the Consumer Guarantees Act, the
Sale of Goods Act and the Fair Trading Act in New Zealand
or any Act or State consumer legislation in the USA or
International markets, imply warranties or conditions, or impose
obligations, upon Oztent which cannot be excluded, restricted
or modified. To the extent permitted by law, the liability of
Oztent (if any) arising out of or in relation to the Product or any
services supplied by Oztent shall be limited (where it is fair and
reasonable to do so),:
(a) in the case of Products, at its option, to the replacement
or repair of the Product or the supply of equivalent
products or the payment of the cost of replacing the
Product or having the Product repaired or of acquiring
equivalent Product. Upon being replaced, parts and
Products become the property of Oztent; or
(b) in the case of services, at its option, to the supply of the
services again or the payment of the cost of having the
services re-supplied;
and in the case of Products or services supplied in the USA or
International markets, loss or damage whether direct or indirect
or consequential that is reasonably foreseeable.
Privacy
You acknowledge that if you make a warranty claim it will be
necessary for Oztent and its Authorised Service Centres to exchange
information in relation to you to enable Oztent to meet its obligations
under this warranty.
Important Notice
Before calling for service please check carefully the owner’s manual,
use and care instructions and the warranty terms and conditions.
Product Registration
To assist in validating warranty, we kindly ask that you register your
product purchase online with Oztent in your country of origin or
alternatively complete the warranty card provided with your product
(if applicable) and return it to Oztent care of the nominated address.
Please visit our website
for more warranty
information & to register
your Oztent product.
oztent.com/product-rego

Oztent Australia Pty Ltd
PO Box Q1700 Sydney NSW 2000
Australia Ph: 02 8706 5100
USA Ph: 855 569 8368
International Ph: [phone]
www.oztent.com