P'kolino Curva Rattan User manual

Made in Brazil.
October/ 2023
2023
FULL
TWO

Made in Brazil.
October / 2023
2023
packaging are to
Full

Curva Rattan Full Bed - Parts:
Phillips screwdriver Hammer
1 h
MANUFACTURER LABEL
DO NOT REMOVE !
Made in Brazil.
October / 2023
2023
1
2
3
4
5
7
8
10
10
10
10
12
12
12
12
12
13
6
6
10
10
10
10
11
11
11
11
11
9

12 - Wooden dowels
1 3/16" (10 x 30mm) (A)
12 - Bolts
3 1/ 1/42" ( " x 90mm) (B)
04 - Bolts
10 - Bolts
3 1/2" (7 x 90mm) (C)
1 9/16" (7 x 40mm)
( )D
12 - Screws
26 - Screws
1 3/8" ( x 35mm)3,5 ( )E
1 3/16" (4 x 30mm) ( )F
FOR MISSING PARTS OR HARDWARE:
DO NOT CONTACT THE STORE WHERE YOU MADE YOUR PURCHASE.DO NOT CONTACT THE STORE WHERE YOU MADE YOUR PURCHASE.
Please contact the manufacturer directly at [email protected] or 888-403-8992.
For customer service cases involving hardware please provide the part number.
Identify the size and type of hardware using the illustration below:
0 -1
Allen wrench ( )H
12 -
1/4 Half Moon Nut ( )G
02 - Wooden spacer ( )I
26 - Screws
1 3/16" (4 x 30mm) ( )F

08
01
1 3/16" Wooden Dowel
1/4" Half
Moon Nut
A
G
Step 1
Step 2
Headboard
Headboard
Insert wooden dowels into the holes as shown in the diagram.8 on to parts and (A)
Hammer
A
A
A
A
AA
A
A
Attach part on part with 1 bolt using 1 Allen wrench .
part with 1 bolt and 1 Half moon Nut ,using 1 Allen wrench .Attach part on
G
H+C
H+B
8
5
GB and C
8
5
01
01
B
C
3 1/2" Bolt
3 1/2" Bolt
H01
Allen
wrench
H
1
PLEASE ASSEMBLE
ON THE GROUND

Phillips screwdriver
Step 4
Headboard
Attach part on to part with , using 1 s and 8 Screws Phillips Screwdriver.
Step 3
Headboard
01
01
B
C
3 1/2" Bolt
3 1/2" Bolt
H01
Allen
wrench
01
1/4" Half
Moon Nut
GB+H
C+H
G
G
H
9
08
E1 3/8" Screw
E
E
E
E
E
E
E
E
PLEASE ASSEMBLE
ON THE GROUND
B and C
Attach part on parts and with 1 bolt ,1 bolt ), 1 half moon nut , using 1 Allen wrench .
E
EE
E
ATTENTION:
JOINTS!
RATTAN INSIDE
THIS FACE
5
8
2
1
2

Step 6
Footboard
Attach part on the part
Attach part and on the part and with 2 bolts and 2 bolts
using 1 Allen wrench .2 Half moon nut and
Step 5
13
04
1 3/16" Wooden Dowel
A
Footboard
Insert wooden dowels into the holes as shown in the diagram.4 on to part (A)
Hammer
A
A
A
A
02
1/4" Half
Moon Nut
G
02
B3 1/2" Bolt
H01
Allen
wrench
13
13
B+H
H+C
C+H
H+B
G
G
PLEASE ASSEMBLE
ON THE GROUND
ATTENTION:
HOLES FACING UP!
7
7
G
H
B and C
3
4
Step 1

Attach part on to parts with 4 Screws , using 1 Phillips Screwdriver.
Step 7
Footboard
Step 8
Siderails
Attach the derail on the with 2 bolts and Si headboard
2 Half moon nuts , using 1 Allen wrench .
Phillips screwdriver
04
E1 3/8" Screw
02
1/4" Half
Moon Nut
G
02
B3 1/2" Bolt
H01
Allen
wrench
MANUFACTURER LABEL
DO NOT REMOVE!
B+H
B+H
G
G
H
B
G
13
7
E
E
E
E
6
In this step
to2 people
is necessary
avoid damage.

Step 9
Siderails
Step 10
Siderails
Attach the derail on the Si and
Attach the on the with 2 bolts and Siderail
with 4 bolts and 4 Half moon nuts ,
using 1 Allen wrench .
2 half moon nuts , using 1 Allen wrench .
04
02
1/4" Half
1/4" Half
Moon Nut
Moon Nut
G
G
04
02
B
B
3 1/2" Bolt
3 1/2" Bolt
H
H
01
01
Allen
Allen
wrench
wrench
H+B
B+H
B+H
H+B
H+B
G
G
G
G
F
F
H+B
H
H
B
B
G
G
In this step
to2 people
is necessary
avoid damage.
MANUFACTURER LABEL
DO NOT REMOVE!
6
6
In this step
to2 people
is necessary
avoid damage.

x5
H+D H+D
Step 11
Bed Slats
1) Attach the slat the with 2 screws s 11 on parts 12 , using . 1 Allen wrench
11
12
H01
Allen
wrench
10
D
1 9/16" Bolt
F
I
I
26
1 3/16" Screw
Phillips screwdriver
F
IWooden spacer
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
F
10
F
F
10
10
10
10
10
10
10
4) Please note warping may occur because it is natural wood.To facilite the placement of the screws,
you must press the two siderails simultaneously.
Step 12
Bed Slats
3 s and 4) Attach the lats with 2 screws , using 1 Philips screwdriver.
2) use the wooden spacer to limit the space between the slats.
1) Attached the rst slat to the end of the side rail base with 2 screws .  , using 1 Phillips screwdriver
11
11
11
11
11
The first slats must be fixed to the end of the
side rail bracket.
After fixed the first slat use the hardware letter ’’ ’’ I
to help define the space between each next slats.
Use 1- on the left side rail and 1- on the right side railI I
(=0mm)
10
10
F
I
I