pagertec Simple Alert User manual

Simple Alert Paging System
USER MANUAL

Thank you for choosing Pagertec
Thank you for choosing Pagertec as your provider for your wireless paging
requirements. We greatly appreciate your confidence in our products. At
Pagertec our greatest commitment is providing you with total customer
satisfaction. Please take a few minutes to review this manual prior to installing
and operating your system. The manual will provide you with installation
instructions, and offer suggestions to ensure you receive all of the many
benefits your system can provide. Additionally, this manual will assist you with
problem determination and offer helpful advice when seeking customer
service. We are confident Pagertec has the most responsive customer
service available within the industry. Please do not hesitate to contact our
Customer Care, if you have any questions. We look forward to a long and
mutually rewarding partnership.

SIMPLE ALERT
PAGING SYSTEM
Installing the Transmitter
The first consideration in the placement of the transmitter is convenience. It should be
readily accessible in a central location within the paging area. Pay close attention to
nearby obstructions such as walls, pipes, ducts, mirrored glass, or other similar barriers
that may weaken or misdirect transmitted signals. Certain materials and construction,
especially metal, have the potential to partially or completely block the paging signal.
The next consideration involves safety. Ensure the unit is securely mounted
and away from liquids, extreme heat and possible physical damage. Also
remember that the transmitting unit requires a 110V-220V AC power outlet. Be
sure an antenna is attached prior to applying power to avoid damage to the
transmitter. An optional molded plastic cover is available as an accessory
purchase, to protect the transmitter, especially in areas where spillage is
possible.
For best results, the transmitter antenna must be vertical. Ideally the transmitter
should be centrally located within the area where paging is to occur. Since this
is not always possible, range testing at different locations may be required to
obtain the desired performance.

CHARGING THE PAGER
1. Do not stack more than 10 guest pagers on a single charging base.
2. Do not connect more than 1 charger base to a single power supply.
3. Only use the power supply that came with your system.
4. Charge pagers for 24 hours prior to first use.
Note: Keep rechargeable pagers on charge even during extremely long periods of inactivity.
WARNING: Damage caused from improper electrical connection including but not limited to the
incorrect power supply is not covered under the standard warranty. If you’re uncertain about which
power supply to use, contact our customer support department.
●The pager will display LOBT when battery level is low. This means it will turn off
within the next 20min approximately.
●Place the pager on the charging base and wait until the GREEN appears on the pager,
this means the pager is fully charged.
OPERATING THE SYSTEM
1. When a guest arrives, remove a pager from the charging stack. Pagers will light up for the
amount of seconds that it's programmed to alert.
2. Record the pager number and hand it to your guest.
3. Page the pager by entering the number into the transmitter.
4. Pagertec Simple Alert Pagers will flash or vibrate (if enabled) depending on the
page mode.
Note: Beep modes will still flash and vibrate (if enabled) with no audible beep.

SET ALERT MODE
You will have the option to program your pagers to do one, two, or all three of the
following alerts: Vibrate - Flash - Beep.
1. Turn the pager around and press the MODE button.
2. Press the LEARN button several times until you reach the mode you desire:
F(Flash), B(Beep), S(Vibrate).
If the pager displays F- the pager will flash
If the pager displays S- the pager will vibrate
If the pager displays FB - the pager will flash and beep
If the pager displays FS - the pager will flash and vibrate
If the pager displays BS - the pager will beep and vibrate
If the pager displays FBS - the pager will flash, beep and vibrate.

3. After you are done choosing, press the STOP button to lock your selection.
SET ALERT TIME
You can set each pager to alert for 15, 30, 45, 60, and 90 seconds.
1. Turn the pager around and press the TIME button.
2. Press the TIME button until you reach the amount of seconds you desire.

TURNING PAGER OFF
●Press the MODE button and STOP button simultaneously.
GROUP PAGING
●If you wish to use the group paging option you can set multiple pagers to the
same number. To change the number of a pager please use the “Sync a pager to
a Transmitter” Instructions.
CANCELING A PAGE
There is two ways you can cancel a page:
1. Press the number of the pager you paged followed by the cancel button.
2. Place the pager back on the charging base and the page will cancel
automatically.

SYNCING A PAGER TO A TRANSMITTER
If you are expanding your system by adding additional pagers please follow the
instructions below to sync your new pagers to your transmitter:
1. Turn the pager around and press the LEARN button and the pager
will display “-- -- -- --”
2. Use the number keys on the transmitter to enter the number you wish the pager
to display.
3. Press the ENTER button on the transmitter to confirm and save your changes.
4. The pager will now reflect the pager number assigned to it.

FCC COMPLIANCE AND ADVISORY STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
Operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, according to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try correct the
interference by one or more of the following measures:
1. Reorient the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into and outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Any special accessories needed for compliance must be specified in the instruction manual.
WARNING: A shielded-type power cord is required in order to meet FCC emission limits
and also to prevent interference to the nearby radio and television reception. It is essential
that only the supplied power cord be used. Use only shielded cables to connect I/O devices to
this equipment.
CAUTION: Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.