Pakedge WR-1 User manual

WR-1
802.11ac Wireless Router
with OvrC
QUICK START GUIDE
OvrC
Enabled

22
Introduction
The Pakedge WR-1 Wireless Router with OvrC gives you the convenience of a high-
throughput wired router integrated with an 802.11ac Wave 2 wireless access point. The
router has features like high throughput and secure OpenVPN, while also supporting
UPnP for simple compatibility with common consumer devices. The WR-1 also
integrates OvrC, which means that you can access the power of OvrC to monitor your
WR-1 from anywhere in the world.
Key features:
• OvrC enabled.
• 500 Mbps WAN-to-LAN firewall throughput
• Maximum data rate: 1.2 Gbps (300 Mbps for 2.4 GHz; 867 Mbps for 5 GHz)
• Secure VPN: Support for OpenVPN
• 2 SSIDs + 2 guest SSIDs
• WPA2-PSK security
• BakPakDDNS: Free Dynamic DNS service built in
• 802.11ac Wave 2 2×2 wireless
• Simple-to-use web GUI

33
Access Point’s
Package contents
• (1) WR-1 router
• (1) Power adapter
• (1) Quick Start Guide
• (1) Ethernet cable
User guide
• For more detailed instructions, refer to the WR-1 User Guide ( pkdge.co/wr1-ug ).
Specifications
• System requirements: Windows or Mac PC with an Ethernet interface.
Credentials
• Admin default username/password: admin/admin
• SSID (default): Pakedge2.4-1 and Pakedge5-1
Security/password: WPA2-PSK/pakedgewireless
• Guest SSID (default): PakedgeGuest2.4 and PakedgeGuest5
Security/password: WPA2/pakedgeguest
• Transmit power: Starting with firmware v1.23, factory default transmit power is
13dBm for 2.4GHz and 18dBm for 5GHz.
• Note your new credentials: ________________________________________

44
Overview
4 3 21WAN
USB 12V/1.5A
RESET
1 2 3 4
A B C
H I JGF
D E
前视图
后视图
A Power
B Internet
C LAN port activity
D 2.4 GHz active
E 5 GHz active
F RESET button
G USB port
H LAN ports
I WAN (to modem/Internet) port
J Power connector

55
Installing
Tools required:
• Computer with Ethernet interface and a web browser
• Ethernet cable
To install the unit:
1 Open the box and remove the WR-1.
2 Ensure that the unit is physically mounted away from obstructions that
could interfere with the wireless signal, such as metal racks or other wireless
transmitting electronic devices.
3 Connect an Ethernet cable from your ISP modem to the WAN port on the WR-1.
4 Connect power to the WR-1.
You are now ready to configure the unit to allow Internet access and register with
OvrC.

66
Logging in
1 After power is connected and a computer is connected to the LAN port, enter the
WR-1’s IP address into the address bar of your web browser. A login screen opens.
Default settings: The IP address will be automatically set to 192.168.1.1.
2 Type your user name and password, then click Login. (The default username is
admin and the password is admin.)
The Quick Setup page appears. The WR-1 Quick Setup page lets you configure
your network’s basic settings. Upon first login, a password change is required.
After the Quick Setup page, you are returned to the Dashboard, where you can
see all of the router’s configuration menus.

77
Quick setup: WAN zone options
DHCP
By default, the wireless router will connect to the Internet using DHCP. If your ISP
uses DHCP, you may need to reset the modem to get Internet access.

88
Static IP
If your ISP uses static IP, enter the IPv4 address,IPv4 subnet mask, IPv4
gateway, and DNS server provided by your ISP. Select Custom from the Subnet
mask drop-down menu to enter a custom subnet mask.

99
PPPoE
If your ISP uses PPPoE, enter the username that the ISP assigned under the PAP/
CHAP username field. Enter the password in the PAP/CHAP password field. For
the Use custom DNS servers field, enter the DNS server you would like to use. For
example, you can use 8.8.8.8.

1010
Registering your WR-1 with OvrC
OvrC gives you remote device management, real-time notifications, and intuitive
customer management, right from your computer or mobile device. Setup is plug-and-
play, with no port forwarding or DDNS address required.
To add this device to your OvrC account:
1 Connect the AP to the internet
2 Log into OvrC (www.ovrc.com)
3 Add the Device (MAC address and serial numbers needed for authentication
Router
Home
Switch
Access Point
Mobile
Apps
WANLAN
Remote Web Browser
Access
1 Gbps
Link/Act