Pakton JVA Z Series User manual

JVA TECHNOLOGIES
www.jva-fence.com
User ManUal

Quick Start Guide
Page 2 © JVA Technologies www.jva-fence.com
1 QUICK START GUIDE
1.1 THE FULL USER MANUAL
The compete user manuals can be downloaded here:
www.jva-fence.com/z11
www.jva-fence.com/z13
www.jva-fence.com/z14
www.jva-fence.com/z18
1.2 LOW VOLTAGE WIRING
Label Type Descripon
IN1 2 Way Energizer control input 1 (dry contact) internally wired
in parallel with the key switch. Arm energizer when
closed
GATE 2 Way Energizer control input 2 (dry contact). Default func-
on is gate input, normally closed. When the unit is
armed and the gate is opened, it will trigger the gate
alarm.
KEYPAD 3 Way Supplies power and data line for an external keypad.
The +12 source on these terminals is protected with
1A self reseng fuse.
SIREN 2 Way Switched 12V output. 30W max, shared between Si-
ren and Strobe. Low side switched
STROBE 2 Way Switched 12V output. 30W max, shared between Si-
ren and Strobe. Low side switched

Page 3
Quick Start Guide
© JVA Technologies www.jva-fence.com Z Series Quick Start Manual
Label Type Descripon
16Vac 3 Way 16Vac 1.5A power input plus earth. Connecon of
the earth is only required where local safety or wir-
ing codes demand it. This should be connected to the
cabinet or mains earth NOT the fence earth.
Ba Battery
leads
12V dc or baery connecon via F1
(4 Amp slow blow fuse).
Relay 3 3 Way “Form C” relay with dry contacts. Default operaon
Fence Alarm
Relay 4 3 Way “Form C” relay with dry contacts. Default operaon
Zone Armed
Relay 5 3 Way “Form C” relay with dry contacts. Default operaon
General Alarm
JUMPERS
Jumpers allow you to turn on and o dierent features, or reset the device
to defaults.
JUMPER FUNCTION
J3 Inhibit AC fail error.
J3(Z14R) Tamper disable.
J4 Factory default jumper - on for normal operaon.
O to return programmable opons to factory defaults on
power up.
J8 Disable on board beeper
J5, J6 & J7 Supplies +12V to the Common terminal of Relay 3, 4, 5.
Jumpers located on the top right hand side of the board

Quick Start Guide
Page 4 © JVA Technologies www.jva-fence.com
1.3 QUICK TEST OF CONFIGURED UNIT
It is a good idea to test the energizer before connecng the it to a fence.
This will give you condence that the unit is operang as expected and it
also isolates potenal fence issues.
To do this, connect your energizer with a “test fence” as shown.
Power the energizer and then Arm it. The unit should begin pulsing and
not show any alarms. Disarm the energizer and remove the fence cable as
shown.
Arm the energizer once again, aer 3 pulses (unless you congured it oth-
erwise) the unit should go into alarm as the fence will appear to be cut.
Check that any sirens, strobes or relays acvate as expected.

Page 5
Quick Start Guide
© JVA Technologies www.jva-fence.com Z Series Quick Start Manual
1.4 CONNECTING TO THE FENCE
A convenonal fence installaon including earth loop monitoring.

Page 6 © JVA Technologies.
Quick Start Guide
Z-Series Quick Start Manual
1.5 CHANGING THE PROGRAMMING OPTIONS
Default Installer PIN 012345 Default User PIN 1234
First you have to enter Programming mode.
Command Key1 Key2 Key3 Key4 Key5 Key6 Key7 Key8 Key9 Enter Programming Mode Installer Pin * 0 #
When you have entered Programming mode you can begin to enter the following opons to congure your Security Energizer. Default Values are highlighted in grey.
Command Key1 Key2 Keys 3 and 4 Key5 Change The Installer PIN 6 Digits
0 0 Enter the new 6 digit Installer PIN #
High Power Mode Power Level
0 1 Enter the value in Hundreds of Volts #
Example: to set 8.2kV, use 82 for keys 3 and 4. Default is 85 (8.5kV)
Low Power Mode Power Level
0 2 Enter the value in Hundreds of Volts #
Example: to set 1.3kV, use 13 for keys 3 and 4. Default is 11 (1.1kV)

Quick Start Guide
Z-Series Quick Start Manual Page 7
Command Key1 Key2 Keys 3 and 4 Key5 Return Fence Alarm Voltage For High Power Mode
0 3 Enter the value in Hundreds of Volts #
Example: to set 3.8kV, use 38 for keys 3 and 4. Default is 40 (4.0kV)
Return Fence Alarm Voltage For Low Power Mode
0 5 Enter the value in Hundreds of Volts #
Example: to set 0.8V, use 08 for keys 3 and 4. Default is 05 0.5kV)
Bad/Missed Pulse Count Before Alarm Triggers
0 6 Enter the number of Missed Pulses #
Example: to set 14 counts, use 14 for keys 3 and 4. Default is 03
Baery Alarm Volt- age (olts). Alarm Val- ue Shown, Reduced Power is 1V less
0700 01 02 03 04 05 06 07 08 09 #
9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5
Siren On Time (S=Seconds, M=Minutes)
0 8 00 01 02 03 04 05 06 07 08 09 #
10S 30S 1M 2M 3M 4M 5M 20M 45M 130M
Siren O Time (S=Seconds, M=Minutes)
0 9 00 01 02 03 04 05 06 07 08 09 #
10S 1M 2M 5M 10M 20M 30M 40M 50M 60M
Siren Cycles 1 0 00 01 02 03 04 05 06 07 08 09 #
012345678 9

Page 8 © JVA Technologies.
Quick Start Guide
Z-Series Quick Start Manual
Command Key1 Key2 Keys 3 and 4 Key5 Gate Entry/Exit Delay (S=Seconds, M=Minutes)
1 3 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M 8M
Chime Mode 1 4 01 02 03 04 05 #
None Door Chime Siren Fence
Alarm
Gate Beeps
Plus Siren
Combined Opons 1 (add up the opons you want. e.g. for Max Power and Limit output: 2 + 4 = 6 Therefore enter 06 for keys 3 and 4
1 6 +2 +4 +8 +16 +32 #
Maximum
Power at all
mes
Limits out-
put to 2.5J
per Zone
Enables IR
Tamper.
Stop slaves
on comms
fail
Stop Ener-
gizer send-
ing alarm
memory
An Bridging Threshold
17 Enter in the percentage dierence required to trigger the An-
Bridging alarm. e.g. if you require a 10% change in return voltage to trigger the alarm, enter 10 for keys 3 and 4. Default is 00 (Disabled)
#

Quick Start Guide
Z-Series Quick Start Manual Page 9
Command Key1 Key2 Keys 3 and 4 Key5 Combined Opons 2 (like Combined Opons 1)
1 8 +1 +2 +4 +8 +16 +32 +64 +128 #
Siren
Chirp
on
Arm
Enable
Entry
Exit
Gate
4800
Baud
9600
Baud
Low
Power
to Bite
Bite to
Low
Power
Auto Re-arm Time S=Seconds, M = Min- utes, D=Disabled
2 0 00 01 02 03 04 05 06 07 08 09 #
0S 30S 1M 2M 3M 4M 5M 6M 7M D
Relay 1 2 1 Opons Explained under “1.6.1 Relay Funcons” Default is 08 # Relay 2 2 2 Opons Explained under “1.6.1 Relay Funcons” Default is 09 # Relay 3 (Z14R only) 2 3 Opons Explained under “1.6.1 Relay Funcons” Default is 00 # Relay 4 (Z14R only) 2 4 Opons Explained under “1.6.1 Relay Funcons” Default is 02 # Relay 5 (Z14R only) 2 5 Opons Explained under “1.6.1 Relay Funcons” Default is 07 # Group Mode 2 6 00 01 02 etc 15 #
No Group Master Slave 1 Slave 14
Input 1 27 Opons Explained under “1.6.2 Input Funcons” Default is (Momen-
tary Arm)
#
Input 2 2 8 Opons Explained under “1.6.2 Input Funcons” Default is 06 (N/O
Gate 1)
#

Page 10 © JVA Technologies.
Quick Start Guide
Z-Series Quick Start Manual
Command Key1 Key2 Keys 3 and 4 Key5 Exit Programming Mode
* #
1.5.1 Relay Funcons The table below is for use for the relay programming opons menoned in the table on the previous page.
Keys 3 and 4
Funcon Descripon
00 Fence Triggers when Zone 1 is Armed and Return Voltage is below the Threshold Voltage
In Bipolar - Triggers when the posive output is below the Threshold Voltage
01 Fence or O Triggers when Zone 1 is Disarmed or Return Voltage is below the Threshold Voltage
02 Armed Zone 1 is Armed
03 Fence 2 Bipolar only - Triggers when the negave output is below the Threshold Voltage
06 Fence Bi-Polar Triggers when energizer is Armed and the fence Return Voltage on either Bi-Polar re-
turn line has fallen below the Threshold Voltage
07 General Triggers on AC Fail, Tamper, Low Baery/Bad Baery, Gate Alarm or Internal error.
Latched (internal errors only)
08 Siren Triggers on Fence Alarm, Gate or Tamper. Will me out aer the Siren Time Out me.
Latched
09 Strobe Triggers on Fence alarm, Gate or Tamper. Only turns o on Energizer Disarm. Latched
10 AC Fail Triggers on AC Fail