Palmer Fixture SF2150 User manual

Touch Free
Bulk Foam Sensor Soap Dispenser
WHITE #9772 / BLACK #9773
Opening the Dispenser
To open the dispenser cover, insert key into slots
at the top of the dispenser (see figure 1). Dispenser
will automatically shut off when cover is opened.
Battery Care Instructions
Open unit (see figure 1).
Open battery cover located on the interior of the
unit on the right side (see figure 2).
Install batteries in proper direction.
(4-C-cell Alkaline Batteries required)
Replace battery cover by inserting notches at an
angle and snapping into place.
Close cover. Dispenser will not operate unless internal
lock snaps closed (see figure 3).
The Indicator Light should slowly flash green (see figure 4).
Check dispenser operation by moving your hands under it. If
it does not work, make sure the cover is closed and the
batteries are properly oriented.
Be sure to dispose of used batteries properly.
Battery Indicator Light
Slow flashing green - standby mode, indicates dispenser
is working properly (see figure 4).
Rapid flashing green - dispenser is delivering soap.
Slow flashing red - batteries require replacement. Without
replacement, the dispenser will eventually stop operating.
CAUTION:
It is the responsibility of the installer to completely read and understand all
instructions and caution statements before proceeding with installation. Following
these instructions will ensure proper function and safety.
Spartan Chemical Company, Inc.
1110 Spartan Drive, Maumee, Ohio 43537
1-800-537-8990 /www.spartanchemical.com
Figure 1
Figure 2
Figure 3
Figure 4
dispenser body
refillable bottle and
foamer valve
#9776 1000 ml
4 screws and 4 anchors
key
White #9774
Black #9775
alcohol wipe
Key
© SCC 11/08
You will need a drill and a screw driver if you are attaching with screws.
Package Includes
Dispenser, refillable bottle and foamer valve, double-sided tape
(attached to dispenser), 4 (four) screws and anchors, alcohol wipe
and key. (batteries not included). Replacement parts are available as labeled.
SF2150

MOUNTING TO WALL WITH TAPE
For glaze tile, painted metal or unpainted metal walls
Thoroughly clean wall surface with included wipe and
let dry completely. (see figure 9) For silicone build-up,
use a pumice-type cleaner or grout cleaner to clean
the surface. Tape will not perform satisfactorily if wall
surface is porous like brick or wood.
Peel paper from back of tape (supplied). (see figure 10)
Press dispenser firmly to the wall and hold for at least
30 seconds to make sure tape has completely adhered
to the wall.
Open dispenser and remove refillable bottle.
(see figure 11)
Locate dispenser above a sink or counter.
Recommended never locating where spillage can fall on
floor creating hazardous condition.
Mount dispenser at least 12" above any surface to
prevent activation of sensor.
Installer will be held responsible for proper installation.
To be in compliance with ADA regulations, the dispenser
should be mounted no more than 48" from the ground.
MOUNTING WITH SCREWS
For porous surfaces like brick or wood
Use included SCREWS AND ANCHORS or other appropriate
hardware based on surface type.
Open dispenser and remove refillable bottle. (see figure 11)
Using the dispenser, mark hole locations on wall.
(see figure 12).
Drill 1/8" diameter holes for anchors and screws or other
hardware (see figure 13). Attach dispenser to wall with
appropriate hardware.
Install 4 c-cell alkaline batteries (See Battery Care
Instructions) and close dispenser. (see figure 14)
Replace refillable bottle.
Tape mount installation should be
allowed to set for 24 hours before filling.
Maintenance Instructions/Battery Replacement
It is important to clean and maintain dispenser and check
battery on a regular, scheduled basis. Failure to do so can
result in dispenser malfunction.
Open dispenser using KEY and remove refillable bottle.
Flush bottle and pump mechanism thoroughly with warm
water to remove residue and contaminates. Refill and
replace bottle. Close dispenser. (see figure 7)
Cleaning all touch-points on dispenser with a disinfectant
should be part of a regular cleaning schedule.
Periodically give the dispenser an overall cleaning. All
internal and external parts should be cleaned thoroughly.
Sensor lens (located underneath dispenser) should be
cleaned regularly with a damp cloth. (see figure 8)
Check Battery Indicator Light (see figure 4) to verify battery
life (See Battery Care Instructions).
TO FILL DISPENSER
CAUTION: For dispenser to work properly, use soap
foam formulated for foaming soap dispensers.
Open dispenser using KEY. (see figure 1)
Remove cap from bottle (see figure 5) and fill with
soap to fill line (see figure 6). For convenience, bottle
can be filled in dispenser or removed prior to filling.
Replace cap and close dispenser.
DISCLAIMER: Not responbible for non-foam soap
use that results in ineffective dispenser operation or
clogging. Soap containing any type of scrubbers will
cause the dispenser to leak and eventually fail.
Figure 1
Figure 5 Figure 6
Figure 7
Figure 8
Figure 10
Figure 11
Figure 12
Key
Figure 9
Figure 13Figure 14