Palmgren 9618602 User manual

operatin manual & parts list
MILLING MACHINE VISES
Read carefully and follow all safety rules and operating instructions before
first use of this product.
9650001.00 - 07/14
Models:
9618401
9618402
9618601
9618602

DESCRIPTION
Palmgren Milling Machine Vises are assembled in the U.S.,
and are constructed from fine grain cast iron with
replaceable steel jaw plates. Lead screws on all models have
a rugged Acme thread. Models 9618402 & 9618602 have a
360° swivel base indicated in 1° increments. Center of base is
open for holding work through body of vise. Base and bed
are parallel to 0.001” on all vises.
SAFETY RULES
•Understand and obey all safety instructions supplied
with drill press, mill or other machines on which vise is
used.
•Bolt or clamp vise to work surface in at least two mount-
ing locations using mounting lugs on swivel base or vise
base.
•Be sure workpiece is clamped securely between jaws
before starting machining operation.
•Do not over tighten—vise can develop a large clamping
force. Use only force which is needed.
•Do not pound or hammer on workpiece. This vise is
designed to clamp the workpiece in a desired position
for machining operations only.
2
Figur 1 - Dim nsions
Palmgren Operating Manual & Parts ist
DIMENSIONS
Refer to Figure 1.
OPERATION
Refer to Figure 2.
•Mount vise to work surface in desired location.
•Open jaws of vise and place workpiece between jaws in
desired position. Secure workpiece between jaws by rotat-
ing leadscrew with handle (Ref. No. 3). Be sure workpiece is
held securely in vise before starting machining operation.
MAINTENANCE
Particles of metal or wood can damage machined surfaces,
causing difficult or inaccurate operation.
•The vise is shipped with a protective coating. This coating
should be removed before operation. Use penetrating oil
to remove protective coating.
•Keep machined surfaces and all moving parts clean and
free of dirt, chips and foreign materials.
•Keep machined surfaces and lead screws lubricated with
medium weight machine oil.
Model A B C D E F Weight
t
9618401 8-7/8" 1-3/4" 4" 4" 14-5/8" 3-3/8" 18 lbs
9618402 8-7/8" 1-3/4" 4" 4" 14-5/8" 4-3/4" 23 lbs
9618601 11-1/4" 2" 6" 6" 20-1/8" 3-7/8
"
35 lbs
9618602 11-1/4" 2" 6" 6" 20-1/8" 5-1/2" 50 lbs

3
Palmgren Operating Manual & Parts ist
REPLACEMENT PARTS LIST FOR MILLING MACHINE VISES
Figure 2 - Replacement Parts Illustration for Milling Machine Vises
Ref. Model Model Model Model
No. Description 9618401 9618402 9618601 9618602
1 N/A N/A N/A N/A
2N/A N/A N/A N/A
3 9610012.00 9610012.00 9610013.00 9610013.00
4 9610044.00 9610044.00 9610045.00 9610045.00
5
6
9610017.00 9610017.00
9610041.00
9610018.00
-
9610018.00
9610043.00
Body
Follower
Lead Screw Assembly
Bottom Plate Kit Jaw
Plate Kit
Swivel Base Kit
(N/A) - Not available as a replacement part.
-
N/A N/A N/A
N/A
7Palmgren Nameplate

Palmgren Operating Manual & Parts ist
WARRANTY
Palmgren warrants their products to be free of defects in material or workmanship. This warranty does not cover defects due directly or
indirectly to misuse, abuse, normal wear and tear, failure to properly maintain the product, heated, ground or otherwise altered, or used for a
purpose other than that for which it was intended. The warranty does not cover expendable and/or wear parts (i.e. v-belts, coated screws,
abrasives), damage to tools arising from alteration, abuse or use other than their intended purpose, packing and freight. The duration of this
warranty is expressly limited to the terms noted below beginning from the date of delivery to the original user. The Palmgren products carry
the following warranties on parts with a 1 year warranty on labor:
•USA Machine vises – ifetime
•IQ Machine vises – ifetime
•Bench vises – ifetime
•Positioning tables – ifetime
•Bench grinders, buffers and belt grinders – 3 years
•Tapping machines – 3 years
•Drilling machines – 3 years
•Finishing machines – 3 years
•Band saws – 3 years
•Work stands – 3 years
•Arbor presses – 3 years
•Milling machines – 3 years
•athes – 3 years
•Accessories – 1 year
The obligation of Palmgren is limited solely to the repair or replacement, at our option, at its factory or authorized repair agent of any part
that should prove deficient. Purchaser must lubricate and maintain the product under normal operating conditions at all times. Prior to
operation become familiar with product and the included materials, i.e. warnings, cautions and manuals. Failur to follow th s instructions
will void th warranty.
This warranty is the purchaser’s exclusive remedy against Palmgren for any deficiency in its products. Under no circumstances is Palmgren
liable for any direct, indirect, incidental, special or consequential damages including lost profits in any way related to the use or inability to
use our products. This warranty gives you specific legal rights which may vary from state to state.
SERVICE & REPAIR
1. If a Palmgren product requires a repair or warranty service DO NOT return the product to the place of purchase.
2. All warranty related work must be evaluated and approved by Palmgren/C.H. Hanson.
3. Prior to returning any item the user must obtain factory approval and a valid RGA number.
4. For instructions and RGA number call toll free [phone].