Paloform Bento 42 Corten Instruction Manual

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference
Burner conforms to: ANSI Z21.97/CSA 2.41 - (2012/10/01) “Outdoor Decorative Gas Appliances”
We recommend that our re pits be
installed and serviced by professionals
that are certied in the U.S. by NFI
(National Fireplace Institute)
DANGER - IF YOU SMELL GAS
1. Shut o gas to the appliance.
2. Extinguish any open ame.
3. If odor continues, keep away from the appliance and immediately call your gas
supplier or re department.
WARNING
Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this
or any other appliance. An LP-cyllinder not connected for use shall not be stored in the
vicinity of this or any other appliance.
CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car
or home.
WARNING:
Improper installation, adjustment, alteration, service or maintenance can cause injury
or property damage. Read the installation, operating and maintenance instructions
thoroughly before installing or servicing this equipment.
WARNING: FOR OUTDOOR USE ONLY!
DANGER
BENTO 42 CONCRETE FIRE PIT Match-lit
Installation + Owner's Manual

2BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
SAFETY INFORMATION
WARNINGS:
IMPORTANT: This appliance should
be inspected before use and at least
once annually by a qualied service
person.
More frequent cleaning may be
required as necessary. It is imperative
that the control compartment,
burners and circulating air
passageways of the appliance be
kept clean.
DANGER: Carbon monoxide
poisoning can lead to death!
CARBON MONOXIDE POISONING:
Early signs of carbon monoxide
poisoning resemble the u, with
symptoms including headache, dizziness,
or nausea. If you experience these
signs, the Fire Pit may not be working
properly. Get fresh air at once! Have the
Fire Pit serviced. Some people are more
aected by carbon monoxide than others,
including pregnant women, people with
heart or lung disease or anemia, those
under the inuence of alcohol, and those
at high altitudes.
NATURAL GAS AND PROPANE:
To assist in detecting leaks, an odorant
has been added to natural gas and
propane. However, this odorant can fade,
and gas may be present even though no
odor exists. Make certain you read and
understand all warnings. Keep this manual
for reference. It is your guide to safe and
proper operation of this appliance.
WARNING: Any modication to this appliance or its
controls can be dangerous.
1. This appliance, as supplied, is only for use with the
type of gas indicated on the rating plate.
2. When this appliance is connected to a xed piping
system, the installation must conform to local codes,
or in the absence of local codes, to the National
Fuel Gas Code, ANSI Z223.1/NFPA 54, or the
International Fuel Gas Code.
3. Keep the appliance area clear and free from
combustible materials, gasoline and other ammable
vapors and liquids
4. Do not burn solid fuel in this appliance. Do not use
this appliance to cook food or to burn paper or other
objects.
5. Children and adults should be alerted to the hazards
of high surface temperatures and should stay away
to avoid burns or clothing ignition.
6. Clothing or other ammable materials should not be
hung from the appliance, or placed on or near the
appliance.
7. Young children should be carefully supervised when
they are in the area of the appliance.
8. Do not use the appliance if any part has been under
water. Immediately call a qualied service technician
to inspect the appliance and to replace any part of
the control system and any gas control which has
been under water.
9. Inspect the appliance before each use.
10. Turn the appliance o and let cool before servicing,
installing, repairing or covering. Any guard or other
protective device removed for servicing the appliance
must be replaced prior to operating the appliance.
Only a qualied service person should install, service,
or repair the appliance.
HIGH ALTITUDE INSTALLATION
The appliance is rated for installations up to 4500’ (1372
m) above sea level. Above 4500’ the appliance must be
derated at the factory for the appropriate altitude unless
the local fuel is pre derated.
LOCAL CODES
Install and use your Outdoor Fire Pit with care. Follow
local codes. In the absence of local codes, use the latest
edition of The National Fuel Gas Code ANSI Z223.1/
NFPA 54 available from:
American National Standards Institute Inc.
1430 Broadway
New York NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy MA 02269.

3BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
BASIC ASSEMBLY
CONTROL KEY
PILOT ASSEMBLY
BURNER RING
BURNER MEDIA PAN
PIPE ADAPTER
FLEX CONNECTOR
VALVE
BODY
1. UNPACK: Account for all parts (see p. 20)
2. FRAGILE: Handle with care
3. LEVEL: Place on a solid, level surface
4. AIR VENTS: Do not block ventilation holes
in base - if applicable (see p. 4)
5. GAS / PROPANE: Supply line is routed
through the base of the unit and must be
installed by licensed trades.
6. MEDIA TOPPINGS: Review correct
placement (p. 7-8)

4BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
DIMENSIONS & SPECIFICATIONS
NATURAL GAS PROPANE
Burner Model # CIR-M-18 CIR-M-18P
Max Heat Input 69,000 BTU/h 60,000 BTU/h
Inlet Pressure - Min. 4.5" W.C 11.0" W.C.
Inlet Pressure - Max. 10.5” W.C. 13.0” W.C.
Orice Size 18 37
Burner Ports 68 68
Port Size 1/8" 1/8" VENTILATION HOLES
(PROPANE ONLY)
GAS SUPPLY OPENING

5BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
FIG 1. MINIMUM CLEARANCES TO COMBUSTIBLES
REQUIRED CLEARANCES
72”72”
12”17”
BENTO 42BENTO 32

6BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
WARNING:
Failure to position parts in
accordance with these diagrams
and instructions and/or failure to
use parts specically approved for
use with this appliance may result
in property damage or personal
injury.
Do not remove the data plates
attached to the Outdoor Fire Pit
Burner. These plates contain
important information.
NOTICE:
Installation and repair should
be done by a qualied service
person. The appliance should be
inspected before use and at least
once annually by a qualied service
person. More frequent cleaning
may be required as necessary.
It is imperative that control
compartment, burner ports and
circulating air passageways of the
appliance be kept clean.
CAUTION:
New Lava Rock may pop or crackle
when rst heated. This should
subside after 30 minutes to one
hour or more of operation. Maintain
safe distance during this time.
ASSEMBLY
TO ASSEMBLE THE FIRE PIT
1. Connect the Burner Assembly to the gas/propane
supply using the supplied ex connector and following
the instructions on page 8.
2. Carefully leak test all connections following the
procedure on page 8.
3. Fill the burner pan evenly with burner media (crushed
tempered glass for natural gas; volcanic rock for
propane). Do not obstruct the pilot lighting port with
burner media! Use burner media supplied by Paloform
only!
4. Follow the Initial Lighting Instructions on page 9.
Make sure that the ame carries to all parts of the
burner. Turn OFF the appliance and let it cool before
proceeding to the next step.
5. Evenly distribute decorative topping (river stones,
crushed glass or lava rock) on top of burner media. An
uneven or excessively thick layer of topping can result
in an uneven ame.
6. Do not cover pilot shield. Keep the lighting port open
and free of media. Do not use any media not supplied
by the manufacturer!
LIGHTING PORT:
DO NOT OBSTRUCT
CORRECT FLAME APPEARANCE
BURNER MEDIA DECORATIVE TOPPING

7BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
BURNER MEDIA & DECORATIVE TOPPING
METAL TABLE TOP
(OPTIONAL)
DECORATIVE TOPPING MEDIA (VARIOUS):
- FILL TOPPING TRAY
- COVER BURNER MEDIA
- KEEP BELOW LID LINE
BURNER MEDIA:
CRUSHED GLASS (NG) or LAVA ROCK (LP)
- FILL BURNER MEDIA TRAY
- COMPLETELY COVER BURNER RING
VENTILATION HOLES (PROPANE ONLY):
DO NOT BLOCK

8BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
APPROVED FLEXIBLE GAS HOSE
A.G.A DESIGN-CERTIFIED MANUAL
SHUTOFF VALVE WITH 1/8” NPT TAP
3” MINIMUM
CAP PIPE NIPPLE TEE JOINT
FROM GAS METER (5” W.C.
TO 10.5” W.C. PRESSURE)
SEDIMENT TRAP
INSTALLATION REQUIREMENTS
Installation must include a manual shuto valve, union,
and plugged 1/8” NPT tap. Locate NPT tap within reach
for test gauge hook up. NPT tap must be upstream from
the appliance.
Apply pipe joint sealant lightly to male threads. This will
prevent excess sealant from going into pipe. Excess
sealant in pipe could result in a clogged burner injector.
Install sediment trap in supply line as shown below.
Locate sediment trap where it is within reach for cleaning
and trapped matter is not likely to freeze.
A sediment trap prevents moisture and contaminants
from entering the Outdoor Fire Pit controls. If a sediment
trap is not installed, or is installed incorrectly, the unit may
not work properly.
CHECKING GAS CONNECTION
WARNING: Test all gas piping and connections
for leaks after installing or servicing. Correct all leaks
immediately.
WARNING: Never use an open ame to check for
a leak. Apply a mixture of liquid soap and water to all
joints. Bubbles forming on joints while the gas is running
indicate a leak. Correct all leaks at immediately.
Test Pressures in Excess Of 1/2 psi (3.5 kPa)
This appliance and its individual shuto valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of ½ psi (3.5 kPa).
Test Pressures Equal To or Less Than 1/2 psi (3.5 kPa)
This appliance must be isolated from the gas supply
piping system by closing its individual manual shuto
valve during any pressure testing of the gas supply piping
system at test pressures equal to or less than ½ psi (3.5
kPa).
CONNECTING TO GAS SUPPLY
WARNING:
A qualied service person must connect
the appliance to the gas supply. Follow all
local codes.
CAUTION:
Use only new black iron or steel pipe.
Internally tinned copper tubing may be
used in certain areas. Use pipe of 1/2”
diameter or greater to allow proper gas
volume to Outdoor Fire Pit Burner. If pipe
is too small, undue loss of pressure will
occur.
INSTALLATION ITEMS NEEDED:
Before installing the Outdoor
Fire Pit, make sure you have all items
listed bellow:
• piping (check local codes)
• sealant
• manual shuto valve
• adjustable (crescent) wrench or pliers
• sediment trap
• tee joints
• pipe wrench

9BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
LIGHTING YOUR FIRE PIT
WARNINGS:
Failure to follow these instructions exactly may result in re or
explosion causing property damage, personal injury or loss
of life.
Before operating the appliance, check all around the appliance
area and on the surrounding oor for the smell of gas - some
gas is heavier than air and may settle on the oor in the event
of a leak. IF YOU SMELL GAS, follow the safety instructions
on page 1 of this manual.
The main gas valve in this appliance is not serviceable. Do not
try to repair or modify the valve, as doing so may result in a re
or explosion. Call a qualied service technician if you have any
safety concerns.
Do not use this appliance if any part of it has been under
water. Immediately call a qualied service technician to
inspect the appliance and to replace any part of the control
system and any gas control that has been under water.
Improper installation, adjustment, alteration, service or
maintenance can result in injury or property damage. For
assistance or additional information, consult a qualied
installer, service agency or the gas supplier.
Do not store or use gasoline or other ammable vapors or
liquids in the vicinity of this appliance.
INITIAL LIGHTING INSTRUCTIONS
1. Purge air from the supply line as follows:
• Open the main shuto valve.
• Unscrew the main pressure test point on the appliance regulator
• Leave the inlet test screw open until gas ows in.
• When the gas is owing, tighten the inlet screw immediately.
2. Test for leaks in each of the following locations:
• The gas supply line connection to the main valve;
• The Burner connections and pilot;
• All joints on the valve and control body;
• All eld made joints and gas shuto valves;
• All factory made joints and connections.
3. You may check for gas leaks using one of the following methods only:
• Soap and water solution. WARNING: If using a soap and water solution to test
for leaks, DO NOT spray the solution onto electronic parts;
• An approved leak testing spray;
• An electronic snier. NOTE: Remove any excess pipe compound from
connections if using this method, as the compound can set o electronic sniers.
DANGER: NEVER USE AN OPEN FLAME TO CHECK FOR GAS LEAKS.

10BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
OPERATING INSTRUCTIONS
Use only your hand to push in or turn the gas control key. Never use tools. If the key will not push in or turn by hand, don’t try
to repair it, call a qualied service technician. Force or attempted repair may result in a re or explosion.
1. Turn the gas control key to the OFF position (it will be necessary to depress the key slightly at the PILOT position). Allow
ve minutes for any gas in the vicinity to dissipate. (LP gas, which is heavier than air, may require forced ventilation).
2. Turn the gas control key to the PILOT position.
3. Push down on the gas control key and light the pilot immediately by applying a ame to the lighting port. Hold the key
down for one full minute after lighting the pilot.
4. When the gas control key is released, the pilot ame should continue to burn (if the pilot goes out, repeat the above steps).
5. Rotate the gas control key from PILOT to ON position (full counterclockwise position) to supply full ow to main burner.
NOTE: Not turning the gas control key to the full ON position will reduce the ow and could result in poor ignition of main
burner.
6. To extinguish main burner, rotate the gas control key clockwise to the PILOT position.
7. To extinguish pilot, depress control key slightly and turn to the OFF position (fully clockwise).
LIGHTING YOUR FIRE PIT
STOP!
Review the safety
information on pages 1, 2
and 8 of this manual.
90°
PILOT
FULL PUSH TO LIGHT
ON OFF
SLIGHT PUSH TO TURN OFF
90°

11BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
THERMOCOUPLE
CLEANING AND MAINTENANCE
BURNER ELEMENT
PILOT ASSEMBLY
KEEP YOUR FIRE PIT COVERED
Covering your re pit with its all-weather cover when not in use will prolong the life of
all its components.
WARNING: Turn o gas before servicing re pit.
We recommend that a qualied service technician perform the following
check-ups at the beginning of each re pit season.
If any irregularities are apparent with operation. Please refer to Troubleshooting guide,
pages 12-13.
BURNER ELEMENT AND PILOT
Keep the burner and pilot area clean by vacuuming or brushing at least twice a year.
Make sure the burner porting and burner air openings are free of obstructions at all
times. Remove pilot cover to inspect pilot.
Remove topping from top of burner ring and Inspect area around the burner. Remove
any lint or foreign material with a brush or vacuum cleaner.
PILOT FLAME
The ames from the pilot should be
visually checked as soon as the unit is
installed, and periodically during normal
operation. The pilot ame must always be
present when the re pit is in operation.
The pilot ame has two distinct ames:
one engulng the thermocouple and the
other reaching to the main burner.

12BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
TROUBLESHOOTING
WARNING:
Turn o appliance and let cool before
servicing. Only a qualied service person
should service and repair this appliance.
IF YOU SMELL GAS:
Shut o gas supply.
Do not try to light any appliance.
Do not touch any electrical switch; do
not use any phone in the vicinity of the
appliance.
Immediately call your gas supplier
from a safe distance. Follow your gas
supplier’s instructions.
IMPORTANT: Operating unit where
impurities in air exist may create
odors. Cleaning supplies, paint, paint
remover, cigarette smoke, cements
and glues, new carpet or textiles,
etc., create fumes. These fumes may
mix with combustion air and create
odors. These odors will disappear
over time.
OBSERVED PROBLEM POSSIBLE CAUSE REMEDY
Unit is smoking / sooting excessively. (Note:
It is natural and unavoidable for appliance
sets to produce moderate levels of carbon
(soot) where ames contact the media.)
1. Poor fuel quality
2. Excessive ame impingement or block-
age
3. Improper fuel/air mixture
1. Contact local natural gas company
2. Separate the stones to allow more
ame passage
3. Remove any foreign items from the
ame pattern and/or check for proper
orice sizing
Burner is excessively noisy
(Note: The movement and combustion of gas
will create low, unavoidable levels of noise.)
1. Passage of air/gas across irregular
surfaces
2. Excessive gas pressure on natural gas
units
1. Relieve any tight bends or kinks in
gas supply line
2. Check/reset gas regulator pressure
Gas odor even when manual valve is in the
OFF position
1. Gas leak. See Warning statement below.
2. Main gas valve defective.
1. Locate and correct all leaks (see
Checking Gas Connections, pg 5)
2. Replace gas valve
Unit produces unwanted odors 1. Gas leak. See Warning statement below. 1. Locate and correct all leaks (see
Checking Gas Connections, pg 5)
Pilot cannot be lit 1. Gas supply turned o or manual shuto
valve closed
2. Air in gas lines when installed
3. Pilot adjustment screw closed
4. Pilot is clogged
1. Turn o gas supply or open manual
shuto valve
2. Purge air from the supply line
3. Adjust pilot ame for approximately
1” blue ame
4. Clean pilot (see Cleaning and Main-
tenance, page 12) or replace pilot
assembly
Pilot does not stay lit after control is released 1. Flame sensor/thermocouple is not hot
enough
2. Thermocouple is damaged
1. Retry, holding control 0key for a
longer period of time (20 seconds or
more) before releasing
2. Replace thermocouple
Burner does not light after pilot is lit 1. Burner orice is clogged
2. Inlet gas pressure is too low
3. Burner orice diameter is too small
4. Flame sensor lead loose or disconnected
1. Clean burner orice
2. Contact local gas or propane supplier
3. Replace burner orice
4. Reconnect or tighten lead
Delayed burner ignition 1. Pilot ame is obstructed 1. Clear media/debris from lighting port
Burner ame is too low 1. Incorrect gas supply or pressure
2. Blocked burner orice or burner ports
3. Improper burner orice size
1. Check for proper gas supply pressure
2. Free burner orice and burner ports of
any burrs, paint, or other blockage
3. Verify proper burner orice sizing (see
page 9)

13BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
ILLUSTRATED PARTS LIST
1
1a
2
3
4
6
5
7
8
13
14
15
16 9
10
11
12
Natural Gas Propane
1Pilot Cover CIR-EPC same
1a Pilot Shroud CIR-EPC same
2Pilot Assembly PIL-M-388 PIL-M-388LP
318” Burner Ring CIR-18-BUR same
4Burner Pan CIR-18-PAN same
5 Valve Stando BEN42-BRA-WR109 same
63/8” Flare Adapter - -
7Regulator M-REG-RV20-NG M-REG-RV20-LP
8 3/8” Close Nipple - -
93/8” 135° Street Elbow - -
10 Valve Bracket (set of 2) BEN32-BRA-WR109 same
11 Main Gas Valve M-VAL-WR-764-109 same
12 Control Key M-KEY-WR109 same
13 Venturi CIR-VEN-1 same
14 Orice FIT-ORI-18 FIT-ORI-37
15 3/8” Street Elbow - -
16 Flex Connector CON-SS-5MM-24 same
17 Burner Media (not shown) Crushed Glass Lava Pebbles
18 Topping Media (not shown) Various Various
19 Fabric Cover (not shown) COV-BEN42-LC same
20 Concrete Vessel (not shown) BEN42-(colour code) same

14BENTO 42 CONCRETE FIRE PIT Match-lit | Installation & Owner's Manual
WARRANTY INFORMATION
RETAIN FOR WARRANTY
MODEL: (circle one) Bento 42-M NG
Bento 42-M LP
SERIAL NO:
DATE PURCHASED:
LIMITED WARRANTY
This product is warranted to the original owner, subject to proof of purchase:
BASIC WARRANTY
Paloform warrants the components and materials in your appliance to be free from manufacturing and material
defects for a period of one year from date of installation. After installation, if any of the components manufactured
by Paloform in the appliance are found to be defective in materials or workmanship, Paloform will, at its option,
replace or repair the defective components at no charge to the original owner. Paloform will also pay for reasonable
labor cost incurred in replacing or repairing such components for a period of one year from date of installation. Any
products presented for warranty repair must be accompanied by a dated proof of purchase.
This Warranty will be void if the appliance is not installed by a qualied installer in accordance with installation
instructions. The Warranty will also be void if the appliance is not operated and maintained according to the
operating instructions supplied with the appliance, and does not extend to (1) re pit burner assembly damaged by
accident, neglect, misuse, abuse, alterations, negligence of others, including the installation thereof by unqualied
installers, (2) the costs of removal, reinstallation or transportation of defective parts on the appliance, or (3)
incidental or consequential damage. All service work must be performed by an authorized service representative.
This warranty is expressly in lieu of other warranties, express or implied, including the warranty of merchantability
of tness for purpose and of all other obligations or liabilities. Paloform does not assume for it any other obligations
or liabilities in connection with sale or use of the appliance. In states that do not allow limitations on how long an
implied warranty lasts, or do not allow exclusion of indirect damage, those limitations of exclusions may not apply
to you. You may also have additional right not covered in the Limited Lifetime Warranty. Paloform reserves the right
to investigate any and all the claims against this Warranty and decide upon method of settlement. For information
about this warranty contact:
Paloform
888.823.8883
[email protected]