Panametrics DigitalFlow GC868 Owner's manual

panametrics.com 910-226P2F1
April 2022
DigitalFlow™ GC868
Panametrics Gas Clamp-On Ultrasonic Flowmeter
Programming Manual (2-Channel)

panametrics.com
Copyright 2022 Baker Hughes company.
This material contains one or more registered trademarks of Baker Hughes Company and its subsidiaries
in one or more countries. All third-party product and company names are trademarks of their respective
holders.
DigitalFlow™ GC868
Panametrics Gas Clamp-On Ultrasonic Flowmeter
Programming Manual (2-Channel)
910-226P2F1
April 2022

ii
[no content intended for this page]

DigitalFlow™ GC868 Programming Manual (2-Channel) iii
Warranty
Warranty Each instrument manufactured by Panametrics is warranted to be free from defects
in material and workmanship. Liability under this warranty is limited to restoring the
instrument to normal operation or replacing the instrument, at the sole discretion of
Panametrics. Fuses and batteries are specifically excluded from any liability. This
warranty is effective from the date of delivery to the original purchaser. If
Panametrics determines that the equipment was defective, the warranty period is:
one year for general electronic failures of the instrument
one year for mechanical failures of the sensor
If Panametrics determines that the equipment was damaged by misuse, improper
installation, the use of unauthorized replacement parts, or operating conditions
outside the guidelines specified by Panametrics, the repairs are not covered under
this warranty.
The warranties set forth herein are exclusive and are in lieu of all
other warranties whether statutory, express or implied (including
warranties of merchantability and fitness for a particular purpose,
and warranties arising from course of dealing or usage or trade).
Return Policy If a Panametrics instrument malfunctions within the warranty period, the following
procedure must be completed:
1. Notify Panametrics, giving full details of the problem, and provide the model
number and serial number of the instrument. If the nature of the problem
indicates the need for factory service, Panametrics will issue a RETURN
AUTHORIZATION number (RA), and shipping instructions for the return of the
instrument to a service center will be provided.
2. If Panametrics instructs you to send your instrument to a service center, it must
be shipped prepaid to the authorized repair station indicated in the shipping
instructions.
3. Upon receipt, Panametrics will evaluate the instrument to determine the cause of
the malfunction.
Then, one of the following courses of action will then be taken:
If the damage is covered under the terms of the warranty, the instrument will be
repaired at no cost to the owner and returned.
If Panametrics determines that the damage is not covered under the terms of the
warranty, or if the warranty has expired, an estimate for the cost of the repairs at
standard rates will be provided. Upon receipt of the owner’s approval to proceed,
the instrument will be repaired and returned.

Warranty
iv DigitalFlow™ GC868 Programming Manual (2-Channel)
[no content intended for this page]

DigitalFlow™ GC868 Programming Manual (2-Channel) v
Contents
Table of Contents
Chapter 1. Programming Site Data
1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1.2 Using the Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1
1.3 Obtaining On-line Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.4 Using the Console Control Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.4.1 Audio Alarm Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.4.2 Stopwatch Totalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.4.3 Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.4.4 Display Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.5 Entering Programming Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1.5.1 Entering Programming Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1.6 Entering Channel Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.6.1 Activating a Channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.6.1.1 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1.6.2 Entering System Data for a Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
1.6.2.1 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
1.6.3 Entering Pipe Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
1.6.3.1 Special Transducers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-10
1.6.3.2 Wedge Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.6.3.3 Pipe Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.6.3.4 Pipe OD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.6.3.5 Pipe Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.6.3.6 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.6.3.7 Reynolds Correction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.6.3.8 Calibration Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
1.6.3.9 Number of Traverses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
1.6.3.10 Transducer Spacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
1.6.3.11 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
1.6.4 Setting Up Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
1.6.4.1 Zero Cutoff. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
1.6.4.2 Temperature Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-12
1.6.4.3 Pressure Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
1.6.4.4 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-13
1.6.5 Entering Setup Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14
1.6.5.1 Setting Signal Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-14
1.6.5.2 Setting Response Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-17
1.6.5.3 Initializing the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-17
1.6.5.4 Setting Advanced Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-18
1.6.5.5 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
1.7 Entering Global Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
1.7.1 Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.7.1.1 Setting the Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.7.1.2 Setting the Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.7.2 Entering Global System Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-22
1.7.2.1 Mass Flow (static)?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23
1.7.2.2 Procedure Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23
1.7.3 Setting Up Global Inputs/Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-23
1.7.3.1 Selecting Error Handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
1.7.3.2 Setting Up Option Cards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
1.7.3.3 Procedure Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27
1.7.4 Setting Up Communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27
1.7.4.1 MODBUS (RS485) Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-28

Contents
vi DigitalFlow™ GC868 Programming Manual (2-Channel)
1.7.4.2 MODBUS/TCP Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-28
1.7.5 MODBUS Register Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-28
1.7.6 Activating Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-30
1.7.6.1 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-31
1.8 Saving Site Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32
1.9 Recalling Site Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32
Chapter 2. Displaying Data
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.2 The BIG Submenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.3 The DUAL Submenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
2.4 The GRAPH Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
2.4.1 Setting Up the GRAPH Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
2.4.2 Using the GRAPH Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
2.5 The LOG Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2.5.1 Entering the LOG Submenu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-5
2.5.2 Numeric Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.5.3 Graphical Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6
2.6 Displaying the Transducer Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8
2.7 Setting the LCD Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-10
2.8 Activating Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11
Chapter 3. Logging Data
3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 Creating a Standard Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
3.2.1 Log Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
3.2.2 STARTTIME Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
3.2.3 START DATE Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
3.2.4 END TIME Prompt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3
3.2.5 END DATE Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.2.6 DURATION Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.2.7 LOG TIME Prompt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.2.8 TIME INCREMENT Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.2.8.1 Procedure Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4
3.3 Checking the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
3.4 Stopping a Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5
3.4.1 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.5 Creating an ERROR Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
3.5.1 Log Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
3.5.2 STARTTIME Prompt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
3.5.3 START DATE Prompt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
3.5.3.1 Procedure Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
Chapter 4. Printing Data
4.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Printing Live Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2.1 Numeric Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2
4.2.2 Graphical Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3
4.3 Printing Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
4.3.1 Numeric Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.3.2 Graphical Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4.4 Printing a Site File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.5 Stop Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4.6 Setting Up a Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7
4.7 Printing Signal Array Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
4.8 Printing RTD Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

DigitalFlow™ GC868 Programming Manual (2-Channel) vii
Contents
Chapter 5. Clearing Data
5.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Reset Totals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2.1 Procedure Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.3 Deleting Site Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
5.3.1 Procedure Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
5.4 Deleting Log Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
5.4.1 Procedure Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2
Chapter 6. Serial Communications
6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 Wiring the RS232 Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.3 Checking the GC868 Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.4 Setting Up the Terminal Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.4.1 Windows 9X/NT Systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2
6.5 The Optional RS485 Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6.5.1 Interface Converter Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-3
6.5.2 Point-To-Point Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-4
6.5.3 Multi-Point Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
6.5.3.1 Reconfiguring a Serial Interface Converter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-5
6.5.3.2 Wiring the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6
6.6 Setting Up an Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
6.7 Setting Up a MODBUS/TCP Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-8
Appendix A. Menu Maps
Appendix B. Data Records
B.1 Option Cards Installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
B.2 Initial Setup Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-2
Appendix C. Programming with PanaView
C.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
C.2 Wiring the RS232 Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
C.3 Setting Up the Communicatio-ns Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
C.3.1 Setting up Ethernet Communicatio-ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3
C.4 Adding the GC868. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4
C.5 Editing Meter Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5
C.5.1 Setting the Meter Clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-7
C.5.2 Reading Transducer Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
C.5.3 Plotting Transducer Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-8
C.5.4 Saving Transducer Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
C.5.5 Clearing Totalizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
C.5.6 Handling Site Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-9
C.5.6.1 Saving an Existing Site to the Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-10
C.5.6.2 Saving a New Site to the Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-10
C.5.6.3 Saving a Site to the PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-10
C.5.6.4 Clearing a Site from the Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11
C.5.6.5 Saving a Site in Text Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-11
C.6 Changing Meter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-12
Appendix D. Foundation Fieldbus Communications
D.1 Optional Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
D.2 Configuration Utility Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-2
D.3 Selecting the Desired Measurements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-2
D.4 Selecting Units for AI Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4
D.5 Resetting Instrument Totalizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5
D.6 Function Block Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6

Contents
viii DigitalFlow™ GC868 Programming Manual (2-Channel)
[no content intended for this page]

DigitalFlow™ GC868 Programming Manual (2-Channel)
Chapter 1. Programming Site Data
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Using the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Obtaining On-line Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Using the Console Control Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Entering Programming Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-7
Entering Channel Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
Entering Global Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-21
Saving Site Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32
Recalling Site Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32

Chapter 1. Programming Site Data
1-1 DigitalFlow™ GC868 Programming Manual (2-Channel)
1.1 Introduction The 2-Channel Model GC868 flowmeter cannot provide accurate flow rate
measurements for either channel until the instrument has been properly installed,
the channel has been activated, and the basic system and pipe parameters have
been programmed into the meter. See the Startup Guide for detailed instructions on
performing these tasks. After completing the installation, proceed with this chapter
to program the Model GC868’s advanced features.
Four submenus within the User Program provide access to the various
programmable features of the Model GC868. Step-by-step programming
instructions for each submenu are presented in this chapter. Refer to the
appropriate section for a discussion of the following User Program submenus:
•CH1/CH2 - use this submenu to activate a channel and to enter the basic setup
parameters for that channel.
•GLOBL - use this submenu to enter global meter parameters (i.e., clock, system,
input/output, communications and security), which apply to both channels.
•SAVE - use this submenu to store both channel and global data in the meter’s
memory, as a site file.
•RECLL - use this submenu to recall and activate a stored site file.
Note: It is not required that both channels of a 2-Channel Model GC868 be
installed. The second channel connector may simply be left vacant for future
expansion.
As an aid in following the programming instructions, a complete menu map of the
User Program is included in Appendix A, Menu Maps .
Note: In the menu map drawings, plain text represents prompt area messages
and boxed text represents option bar choices. Fx represents a function key to
select an option bar choice.
1.2 Using the
Keypad The Model GC868 keypad contains 39 keys, which are labeled with their primary
(unshifted) functions. In addition, pressing the red [SHIFT] key will access the
secondary functions assigned to most of the keys.
The complete keypad is illustrated in Figure 1-1 below and a detailed description of
both the unshifted and shifted functions for each of the 39 keys is listed in Table 1-1
on page 1-2.
Note: Only the [SHIFT] key and the eight [Fx] keys have no shifted function.

DigitalFlow™ GC868 Programming Manual (2-Channel) 1-2
Chapter 1. Programming Site Data
Figure 1-1: The Model GC868 Keypad
Note: Although the keypad is essentially the same, the front panel layout of meters
supplied in one of the optional enclosures is different. See Appendix C,
Optional Enclosures , of the Startup Guide for a picture of the applicable front
panel.
H I J K L M N
W
PROG
Q
EXIT
SCREEN
V
DISP CAL
O P
CLR HELP
LOG 0
X Y Z
PRNT 1 2 3
4 5
R S T
ENT 6
U
A B C D E F G
7 8 9
Table 1-1: Model GC868 Key Functions
Key Unshifted Function Shifted Function
Software Function Keys - press to select
the functions displayed directly above
them in the option bar. These keys apply
only to the left pane of the display screen.
None

Chapter 1. Programming Site Data
1-3 DigitalFlow™ GC868 Programming Manual (2-Channel)
Software Function Keys - press to select
the functions displayed directly above
them in the option bar. These keys apply
only to the right pane of the display
screen.
None
Shift Key - use this red key to access the
shifted function of the other keys. One
press shifts the next keystroke only. Two
presses locks the keypad in shifted mode.
A third press releases the shift function.
None
Arrow Keys - in measurement mode, use
to scroll through function choices on the
option bar. In programming mode, use to
scroll through menu choices. The [←] also
acts as a backspace key in programming
mode.
Use to enter the letters A, B, C and
D, respectively.
Program Key - press to enter the User
Program . See page 1-8 for details. Use to enter the letter Q.
Display Key - use to display data in a
variety of numeric and graphic formatting
options. See page 2-2 for details.
Use to enter the letter O.
Log Key - use to set up logs. See page 3-1
for details. Use to enter the letter X.
Print Key - use to print live measurements,
log files and signal arrays. See page 4-2
for details.
Use to enter the letter R.
Clear Key - use to reset totals and to
delete site and log files from the Model
GC868 memory. See page 5-1 for details.
Use to enter the letter H.
Calibration Key - use to calibrate the
analog inputs and outputs and to test the
alarm relays and the totalizer/frequency
outputs. See Chapter 1, Calibration , of the
Service Manual for details.
Use to enter the letter P.
Table 1-1: Model GC868 Key Functions
Key Unshifted Function Shifted Function
PROG
DISP
LOG
PRNT
CLR
CAL

DigitalFlow™ GC868 Programming Manual (2-Channel) 1-4
Chapter 1. Programming Site Data
Exit Key - use to move up one level in the
user program or to exit the user program.
See page 1-10 for details.
Use to enter the letter J.
Enter Key - use to confirm the most recent
input information. Use to enter the letter K.
Help Key - use to access the Model
GC868’s context-sensitive on-line help
system. See the next section for details.
Use to enter the letter I.
Screen Key - press the left side to select
the left display pane or press the right side
to select the right display pane.
Press the left side to enter the
letter V or press the right side to
enter the letter W.
Decimal Point Key - press to enter a
decimal point during numeric entry. Use to enter the letter Z.
Minus Key - use to enter a minus sign or a
dash. Use to enter a space character.
Zero Key - use to enter the number 0. Use to enter the letter Y.
One Key - use to enter the number 1. Use to enter the letter S.
Two Key - use to enter the number 2. Use to enter the letter T.
Three Key - use to enter the number 3. Use to enter the letter U.
Four Key - use to enter the number 4. Use to enter the letter L.
Five Key - use to enter the number 5. Use to enter the letter M.
Six Key - use to enter the number 6. Use to enter the letter N.
Seven Key - use to enter the number 7. Use to enter the letter E.
Eight Key - use to enter the number 8. Use to enter the letter F.
Nine Key - use to enter the number 9. Use to enter the letter G.
Table 1-1: Model GC868 Key Functions
Key Unshifted Function Shifted Function
EXIT
ENT
HELP
SCREEN
0
1
2
3
4
5
6
7
8
9

Chapter 1. Programming Site Data
1-5 DigitalFlow™ GC868 Programming Manual (2-Channel)
1.3 Obtaining
On-line Help A context-sensitive, on-line help system is programmed into every Model GC868
flowmeter. On-line help, which displays additional information related to the current
task, may be accessed at any time by pressing the [HELP] key on the keypad. The
help information will be shown on the currently selected pane of the display screen,
as shown in Figure 1-2 below.
Figure 1-2: Typical On-Line Help Screen
After entering the on-line help system, the following functions are available on the
option bar of the selected display pane:
•MORE: Press [F1] (or [F5]) to access this function, and the next screen of text is
displayed in the prompt area.
•EXIT: Press [F2] (or [F6]) to access this function, and the Model GC868 returns to
measurement mode.
•ERROR: Press [F3] (or [F7]) to access this function, and the various Model GC868
error codes are displayed. Use the [F1]-[F4] (or [F5]-[F8]) function keys, in
conjunction with the [←] and [→] keys, to obtain additional information on the
desired error code or to exit the help system.
Note: See the Service Manual for a complete listing of all error codes and
messages.
Audio Level Key - press to increase the
audio alarm volume. Press to decrease the audio alarm volume.
Stopwatch Timer Key - press to turn the
stopwatch timer on. Press to turn the stopwatch timer off.
Backlight Key - press to turn the display
backlight on or to increase its brightness. Press to turn the display backlight off or to decrease its brightness.
Contrast Key - press to increase the
contrast of the display screen. Press to decrease the contrast of the display screen.
Table 1-1: Model GC868 Key Functions
Key Unshifted Function Shifted Function
MORE FLOWEXIT ERROR
ON-LINE HELP
MORE EXIT ERROR FLOW

DigitalFlow™ GC868 Programming Manual (2-Channel) 1-6
Chapter 1. Programming Site Data
•FLOW: Press [F4] (or [F8]) to access this function, and the various flow
measurement parameters are displayed. Use the [F1]-[F4] (or [F5]-[F8])
function keys, in conjunction with the [←] and [→] keys, to obtain additional
information on the desired measurement parameter or to exit the help system.
1.4 Using the
Console Control
Keys
The Model GC868 has four console control keys, which are located on the left side of
the keypad. Use these keys, which are described and pictured in Table 1-1 on page
1-2, in accordance with the following instructions:
1.4.1 Audio Alarm
Volume Use the top console control key to adjust the audio alarm volume.
Discrete presses will incrementally increase the volume of the audio alarm. Hold the
key down for continuous increase. Use the key in shifted mode to decrease the
volume of the audio alarm.
1.4.2 Stopwatch
Totalizer Use the second console control key for the stopwatch totalizer.
Press the key once to start the stopwatch totalizer. Press the key once, in shifted
mode, to stop the stopwatch totalizer.
Note: Instructions on properly setting up the stopwatch totalizer are given later in
this chapter. Also, the Service Manual provides information on the error
response of the stopwatch totalizer.
1.4.3 Display Brightness Use the third console control key to adjust the display backlight.
Discrete presses of this key will increase the backlight brightness through settings of
Off, Mid and Full. Discrete presses of this key in shifted mode, will decrease the
backlight brightness through settings of Full, Mid and Off.
Note: The display backlight has an automatic time-off feature. See page 1-10 for
setup instructions.
1.4.4 Display Contrast Use the bottom console key to adjust the display contrast.
Discrete presses will incrementally increase the display contrast. Hold the key down
for continuous increase. Use the same key, in shifted mode, to decrease display
contrast.

Chapter 1. Programming Site Data
1-7 DigitalFlow™ GC868 Programming Manual (2-Channel)
1.5 Entering
Programming
Mode
Use the keypad, as described in Chapter 3, Operation , of the Startup Guide to
navigate through the User Program . The menu map may be followed in sequence, or
the [↑] and [↓] keys may be used to scroll through the prompt screens. The [←]
key may be used to delete the last alphanumeric character that was entered from
the keypad.
The following discussion assumes that the left screen pane is active. If the right
screen pane is active, only the function key designations change. That is, replace
[F1]-[F4] with [F5]-[F8]. Also, Channel 1 is used in all examples, but the instructions
apply equally to Channel 2.
Note: Be sure to record all the programming data entered in this chapter in
Appendix B, Data Records .
Programming of the ACTIV, SYSTM and PIPE submenus is necessary for operation of
the Model GC868. Failure to accurately enter all of the required information will result
in unreliable flow rate data. Therefore, be sure to complete at least the sections of
this chapter pertaining to those three submenus.
Note: Because it is so essential, instructions for programming the ACTIV, SYSTM
and PIPE submenus are also included in the Startup Guide . If that
programming has already been completed, skip the corresponding sections
of this chapter.
Except for the three submenus noted above, it is not necessary to program the
Model GC868 flowmeter in any particular order. Therefore, the sections of this
chapter need not be completed in sequence. Proceed immediately to any section of
interest.
1.5.1 Entering
Programming
Mode
To access the User Program , press the [PROG] key on the keypad. The standard
measurement mode screen will be replaced by the following initial programming
mode screen:
Note:
If the security feature is active, enter the password and press the [ENT] key to enter
the User Program. See the SECUR submenu section of this chapter on page 1-30 for
more information on the security feature.
PROGRAM Start Press the [←] and [→] keys
and one of the function keys
[F1]-[F4] to select the
desired submenu. From this
screen, press [EXIT] to return
to measurement mode.
PROGRAM
Channel 1
CH1 CH2 GLOBL SAVE

DigitalFlow™ GC868 Programming Manual (2-Channel) 1-8
Chapter 1. Programming Site Data
1.6 Entering
Channel Data After selecting [F1]=CH1 (or [F2]=CH2) at the initial programming screen, the
following screen appears:
Based on the selection made above, proceed to the appropriate section of this
chapter for instructions.
1.6.1 Activating a
Channel The ACTIV submenu activates a channel and selects the desired measurement
method.
1. To enter the Channel PROGRAM menu, press [F1] or [F2] (depending on the
desired channel) at the User PROGRAM prompt.
2. Enter the ACTIV submenu by pressing [F1] at the Channel PROGRAM prompt.
3. Press [F1] (OFF) to deactivate the channel and return to the Channel PROGRAM
prompt, or press [F2] to activate the channel in BURST mode.
4. Press [F1] to select Skan mode, [F2] to select Skan/Measure Integrate mode,
[F3] to select Skan/Measure Count mode, or [F4] to select Skan/Correlation
mode . The meter will exit the ACTIV submenu and return to the channel menu
screen.
a. If you select Skan or Skan/Measure Count modes, the GC868 asks if you will Use
703-1273 DSP? (the digital signal processing board). Press [F2] to apply the
board, or [F1] to apply the onboard signal processing. (The factory recommends
using the DSP for improved response time.)
The Model GC868 flowmeter can take measurements in four different ways
• Skan is a low resolution technique for locating the acoustic signal and for high
velocity measurements. It is more robust in a noisy environment than the
Measure technique. A variation, the Skan/Correlation mode, is used primarily for
liquid detection applications.
• Measure is a more precise technique best used for low velocity measurements.
You can choose from Skan/Measure Count (the default technique) or
Skan/Measure Integrate (the traditional Skan/Measure mode).
IMPORTANT: Consult with the factory before selecting the Skan/Correlation or
Skan/Measure Integrate modes.
If Skan is selected at the next prompt, the instrument uses this technique exclusively.
However, if one of the S/M modes is selected, the meter uses Skan to find the
acoustic signal and then tries to use the Measure technique for a more precise
measurement.
Note: To change the Skan and Measure parameters, see the SIGNL and ADVAN
submenu sections of this chapter.
Chan 1 PROGR Start Press the [←] and [→] keys
and a function key [F1]-[F4]
to select the desired
submenu. From this screen,
press [EXIT] to return to the
initial User Program screen
shown on page 1-8.
Channel PROGRAM
status
ACTIV SYSTM PIPE I/O

Chapter 1. Programming Site Data
1-9 DigitalFlow™ GC868 Programming Manual (2-Channel)
1.6.1.1 Procedure Options After completing the above steps, the meter returns to the Channel PROGRAM
prompt. Continue as follows:
• To continue programming the meter, refer to the menu maps in Appendix A
and navigate to the desired menu. Then, proceed to the appropriate section of
this manual for instructions.
• To leave the User Program and retain the previous settings, press [EXIT] twice
and then press [F1] = NO at the SAVE prompt. Any programming changes will
be discarded and you will be returned to the data display.
• To leave the User Program and return to measurement mode, press [EXIT]
twice and then press [F2] = YES at the Save prompt. Your programming
changes will be entered into the meter’s memory, and you will be returned to
the data display.
Note: See the SAVE submenu section on page 1-32 of this chapter for more
information on this function.
1.6.2 Entering System
Data for a Channel Refer to Figure A-1 on page A-1.
1. To enter the Channel PROGRAM menu, press [F1] or [F2] (depending on the
desired channel) at the User PROGRAM prompt.
2. To program the SYSTM submenu, press [F2] at the Channel PROGRAM prompt.
IMPORTANT: Do not confuse this SYSTM submenu, which is used to enter
channel-specific information, with the SYSTM submenu of the GLOBL
menu, which is used to enter information applicable to both channels.
3. Enter a Channel Label of up to 9 characters. Press [ENT].
4. Enter a Channel Message of up to 21 characters. Press [ENT].
5. At the Equation prompt, select the gas equation used by the meter to perform its
flow rate calculations. Press [F1] = STAND to display data in Standard volumetric
units, or press [F2] = ACTUL to display data in Actual volumetric units.
a. If you selected Standard , press [F1] to have the meter treat the gas as an ideal
gas or press [F2] to have the meter treat the gas as a supercompressed gas .
6. Use the [→] and [F1]-[F4] keys to select the Volumetric Units for the data
display, as shown in Table 1-2 below.
7. Use the [F1]-[F4] keys to select the Volumetric Time for the data display.
8. Use the [F1]-[F4] keys to select the Vol Decimal Digits (the number of digits to
the right of the decimal point) in the data display.
9. Use the [→] and [F1]-[F4] keys to select the Totalizer Units for the data display.
10. Use the [F1]-[F4] to select the Total Decimal Digits (the number of digits to the
right of the decimal point) in the data display.
Table 1-2: Available Volumetric/Totalizer Units
English Metric
Actual Units
ACF = Actual Cubic Feet ACM = Actual Cubic Meters
KACF = Thousands of ACF KACM = Thousands of ACM
MMACF = Millions of ACF MMACM = Millions of ACM
Standard Units
SCF = Standard Cubic Feet SCM = Standard Cubic Meters
KSCF = Thousands of SCF KSCM = Thousands of SCM
MMSCF = Millions of SCF MMSCM = Millions of SCM