Panasonic KX-TS620CB User manual

Operating Instructions
Telephone Answering System
Model No. KX-TS620CB
This unit is compatible with Call Display. To use this feature, you must subscribe to
the appropriate service offered by your service provider.
Please read these Operating Instructions before using the unit and save for future
reference.
For assistance, please call 1-800-561-5505 or visit us at www.panasonic.ca
TS620bk01.book Page 1 Wednesday, June 14, 2006 2:18 PM

2
Introduction
Accessory Information.......................3
Preparation
Important Information ........................ 4
Important Safety Instructions ............ 5
Location of Controls .......................... 7
Display............................................... 9
Settings
Connecting the Handset
/
AC Adaptor
/ Telephone Line Cord .... 10
Connecting a Communication
Device ............................................. 11
Programming Summary .................. 12
Time and Date................................. 13
Display Language............................ 14
Dialing Mode ................................... 15
LCD Contrast................................... 15
Ringer Volume................................. 16
Time Adjustment
(Call Display subscribers only)........16
Preparing the Answering System
Greeting Message ........................... 17
Programming Summary for the
Answering System........................... 19
Number of Rings ............................. 20
Caller’s Recording Time .................. 21
Screening Calls ............................... 21
Making/Answering Calls
Making Calls.................................... 22
Answering Calls............................... 24
Call Display Service
Private Name Display...................... 25
Call Waiting Deluxe Service ............ 26
Viewing the Caller List..................... 27
Calling Back from the Caller List ..... 29
Editing a Caller List Information ......29
Storing Caller List Information
in the Phonebook ............................ 30
Storing Caller List Information in
the Direct Dial memory....................31
Erasing Caller List Information ........ 32
Phonebook
Storing Names and Numbers in the
Phonebook ......................................33
Dialing from the Phonebook ............35
Chain Dial........................................36
Editing .............................................37
Erasing ............................................37
Direct Dial (M1, M2, M3)
Storing Names and Numbers in the
Direct Dial memory..........................38
Dialing a Stored Number from the
Direct Dial memory..........................39
Special Features
Temporary Tone Dialing
(For Rotary or Pulse
Service Users).................................40
How to Use the PAUSE Button
(For PBX Line/Long
Distance Calls) ................................40
Muting Your Conversation................40
For Call Waiting Service Users........41
To Use Call Waiting
Deluxe Service ................................41
Setting Hold Music to ON/OFF........43
FLASH Button .................................44
Setting the Password.......................45
Call Restriction ................................46
Answering System
Automatic Answering Operation ......47
Setting the Unit to Answer Calls ......47
Listening to Messages.....................48
Recording Your Telephone
Conversation....................................49
Erasing Messages ...........................49
Remote Operation from a
Touch Tone Phone...........................50
Remote Code ..................................51
Voice Menu......................................52
Direct Remote Operation.................54
Useful Information
Wall Mounting..................................56
Optional Headset.............................57
Troubleshooting ...............................58
Specifications ..................................61
Warranty ............................ Back cover
Table of Contents
TS620bk01.book Page 2 Wednesday, June 14, 2006 2:18 PM

3
Thank you for purchasing your new Panasonic telephone
answering system.
For your future reference
Serial No. Date of purchase
(found on the bottom of the unit)
Name and address of dealer
Accessory Information
∑AC Adaptor (p. 10) : one ∑Handset Cord (p. 10) : one
∑Handset (p. 10) : one ∑Telephone Line Cord (p. 10) : one
Introduction
TS620bk01.book Page 3 Wednesday, June 14, 2006 2:18 PM

4
Important Information
NOTICE:
This equipment meets the applicable
Industry Canada Terminal Equipment
Technical Specifications. This is confirmed
by the registration number. The
abbreviation, “IC:”, before the registration
number signifies that registration was
performed based on a Declaration of
Conformity indicating that Industry Canada
technical specifications were met. It does
not imply that Industry Canada approved
the equipment.
Before installing this equipment, users
should ensure that it is permissible to be
connected to the facilities of the local
telecommunications company. The
equipment must also be installed using an
acceptable method of connection. The
customer should be aware that compliance
with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be
coordinated by a representative designated
by the supplier. Any repairs or alterations
made by the user to this equipment, or
equipment malfunctions, may give the
telecommunications company cause to
request the user to disconnect the
equipment.
Users should ensure, for their own
protection, that the electrical ground
connections of the power utility, telephone
lines and internal metallic water pipe
system, if present, are connected together.
This precaution may be particularly
important in rural areas.
Caution:
Users should not attempt to make such
connections themselves, but should contact
the appropriate electric inspection authority,
or electrician, as appropriate.
NOTICE:
The Ringer Equivalence Number (REN)
assigned to each terminal device provides
an indication of the maximum number of
terminals allowed to be connected to a
telephone interface. The termination on an
interface may consist of any combination
of devices subject only to the requirement
that the sum of the Ringer Equivalence
Numbers of all the devices does not
exceed 5.
The Ringer Equivalence Number (REN) of
this unit:
(found on the bottom of the unit).
Preparation
TS620bk01.book Page 4 Wednesday, June 14, 2006 2:18 PM

5
Preparation
Important Safety
Instructions
When using this unit, basic safety
precautions should always be followed to
reduce the risk of fire, electric shock, or
personal injury.
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on this unit.
3. Unplug this unit from power outlets
before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for
cleaning.
4. Do not use this unit near water, for
example near a bathtub, washbowl,
kitchen sink, etc.
5. Place the unit securely on a stable
surface. Serious damage and/or injury
may result if the unit falls.
6. Do not cover slots and openings on the
unit. They are provided for ventilation
and protection against overheating.
Never place the unit near radiators, or
in a place where proper ventilation is
not provided.
7. Use only the power source marked on
the unit. If you are not sure of the type
of power supplied to your home,
consult your dealer or local power
company.
8. Do not place objects on the power
cord. Install the unit where no one can
step or trip on the cord.
9. Do not overload power outlets and
extension cords. This can result in the
risk of fire or electric shock.
10. Never push any objects through slots in
this unit. This may result in the risk of
fire or electric shock. Never spill any
liquid on the unit.
11. To reduce the risk of electric shock, do
not disassemble this unit. Take the unit
to an authorized service center when
service is required. Opening or
removing covers may expose you to
dangerous voltages or other risks.
Incorrect reassembly can cause
electric shock when the unit is
subsequently used.
12. Unplug this unit from the power outlet
and refer servicing to an authorized
service center when the following
conditions occur:
A. When the power supply cord or plug
is damaged or frayed.
B. If liquid has been spilled into the
unit.
C. If the unit has been exposed to rain
or water.
D. If the unit does not work normally by
following the operating instructions.
Adjust only controls covered by the
operating instructions. Improper
adjustment may require extensive
work by an authorized service
center.
E. If the unit has been dropped or
physically damaged.
F. If the unit exhibits a distinct change
in performance.
13. During thunderstorms, avoid using
telephones except cordless types.
There may be a remote risk of an
electric shock from lightning.
14. Do not use this unit to report a gas
leak, when in the vicinity of the leak.
SAVE THESE
INSTRUCTIONS
TS620bk01.book Page 5 Wednesday, June 14, 2006 2:18 PM

6
Preparation
CAUTION:
Installation
• Never install telephone wiring during a
lightning storm.
• Never install telephone jacks in wet
locations unless the jack is specifically
designed for wet locations.
• Never touch the uninsulated telephone
wires or terminals unless the telephone
line has been disconnected at the network
interface.
• Use caution when installing or modifying
telephone lines.
• Do not touch the plug with wet hands.
General
• Use only the AC adaptor included with this
product noted on page 10.
• Do not connect the AC adaptor to any AC
outlet other than a standard AC 120 V
outlet.
• This product is unable to make calls when:
=the key lock feature is turned on.
=the call bar feature is turned on (only
phone numbers stored in the unit as
emergency numbers can be called).
• Care should be taken so that objects do
not fall onto, and liquids are not spilled into
the unit. Do not subject this unit to
excessive smoke, dust, mechanical
vibration or shock.
Environment
• The product should be kept free from
excessive smoke, dust, high temperature
and vibration.
• The product should not be exposed to
direct sunlight.
• Do not place heavy objects on top of the
product.
• When you leave the product unused for a
long period of time, unplug the product
from the power outlet.
• The product should be kept away from
heat sources such as heaters, kitchen
stoves, etc. It should not be placed in
rooms where the temperature is less than
5°C (41°F) or greater than 40°C (104°F).
Damp basements should also be avoided.
• The AC adaptor is used as the main
disconnect device. Ensure that the AC
outlet is installed near the unit and is
easily accessible.
Routine care
• Wipe the outer surface of the product with
a soft moist cloth. Do not use benzine,
thinner or any abrasive powder.
WARNING:
• To prevent the risk of fire or electrical
shock, do not expose this product to rain
or any type of moisture.
• Unplug this unit from power outlets if it
emits smoke, an abnormal smell or makes
unusual noise. These conditions can
cause fire or electric shock. Confirm that
smoke has stopped and contact an
authorized service centre.
TS620bk01.book Page 6 Wednesday, June 14, 2006 2:18 PM

7
Preparation
Location of Controls
How to use the Navigator key and {OK}button
This key has five active areas that are indicated
by arrows and {OK}.
• Pressing the {3}and {4}arrows allows you to enter
the Caller List and scroll through the function menu, the
Caller List and the Phonebook list.
• Pressing the {:}and {9}arrows allows you to:
=enter the Phonebook list.
=move the cursor when entering items.
=to repeat and skip a message during playback.
• The {OK}button is used to select or confirm your menu
choices.
Navigator Key
({4},{3},{:},{9}and
{OK}) (p. 12, 19, 35)
Direct Dial ({M1}, {M2}, {M3})
(p. 31, 38)
Headset Jack (p. 57)
{£}(TONE) (p. 40)
Display (p. 9)
{HOLD/RINGER}(p. 16, 24)
{PAUS E}(p. 40)
{FLASH}(p. 41, 44)
{REDIAL}(p. 23)
{SP-PHONE/HEADSET}
and Indicator (p. 22, 24, 57)
{MUTE}(p. 40)
MIC (Microphone)
(p. 22, 24)
RINGER Indicator
(p. 24, 25)
Throughout these
Operating Instructions,
the navigator key is
indicated by the arrows
{4}, {3}, {:}, {9}
and {OK}.
OK
TS620bk01.book Page 7 Wednesday, June 14, 2006 2:18 PM

8
Preparation
{FUNCTION/EDIT}
(p. 12, 19, 29)
{EXIT}(p. 12, 19, 27, 35)
{ANSWER ON}(p. 47)
{GREETING CHECK}(p. 18)
{ERASE}
(p. 18, 32, 39, 49)
{MESSAGE/2WAY REC}
and Indicator (p. 48, 49)
{STOP}(p. 18, 48)
{GREETING REC}(p. 17)
TS620bk01.book Page 8 Wednesday, June 14, 2006 2:18 PM

9
Preparation
Display
(This display shows all the possible
configurations.)
When the handset is on the cradle, the AC adaptor is
connected and the SP-PHONE/HEADSET indicator
light is off, the display shows the current time and date,
the number of new calls, and the number of recorded
messages.
If “ ” flashes on the display, the clock needs
adjustment (p. 13, 14).
During a conversation, the display shows the length of
the call (Example: 1 hour, 6 minutes and 35 seconds).
This is a display from the Caller List.
The display shows:
— the caller’s name and number,
— the time and date of the call
(Example: Nov. 24, 11:50 AM).
: The unit enters in the Phonebook (p. 33).
: The unit plays music during the hold for a caller (p. 43).
: The second call has been received while talking (p. 41).
: {MUTE}was pressed during a conversation (p. 40).
: The ringer is set to off (p. 16).
: {REDIAL}was pressed while the handset is on the cradle and the
SP-PHONE/HEADSET indicator is off (p. 23).
: {PAUSE}was pressed while dialing or storing phone numbers.
: {FLASH}was pressed while storing phone numbers.
ABCDEFGHIJKLMNOP
123456789 123456
abcdefghijklmnop
5 messages
1 missed calls
12
:
34AM DEC.31
message
12:AM DEC.31
12 34
:AM DEC.15
1- 6-35
11:5 AM NOV.24
111-444-7777
SMITH,JACK
P
F
TS620bk01.book Page 9 Wednesday, June 14, 2006 2:18 PM

10
Connecting the Handset /AC Adaptor/ Telephone Line
Cord
After line connection, lift the handset to check for a dial tone.
• USE ONLY WITH Panasonic AC ADAPTOR PQLV207.
• Use only a Panasonic Handset for the KX-TS620CB.
• The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel
warm during use.)
• The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet.
Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the
adaptor may cause it to become disconnected.
• If your unit is connected to a PBX which does not support Call Display services, you
cannot access those services.
Hook
Telephone
Line Cord
To Power Outlet
(AC 120 V, 60 Hz)
Handset
Handset Cord
To Single-Line
Telephone Jack (RJ11C)
AC Adaptor
Fasten the AC
adaptor cord
to prevent it
from being
disconnected.
LINE
Settings
TS620bk01.book Page 10 Wednesday, June 14, 2006 2:18 PM

11
Settings
If you subscribe to a DSL service:
• Please attach a noise filter (contact your DSL provider) to the telephone line between the
unit and the telephone line jack in the event of the following:
= Noise is heard during conversations.
= Call Display feature (p. 25) does not function properly.
Connecting a Communication Device
If you want to connect a communication device (computer, modem, fax, etc.) to the
telephone line, you can connect it through this unit using the DATA jack.
After connecting the handset, AC adaptor and telephone line cord (p. 10), connect
the communication device telephone line cord to the DATA jack.
• Make sure the communication device is not in use before using this unit (making calls,
storing phone numbers in memory etc.) or the communication device may not operate
properly.
Noise Filter
(For DSL Users) Telephone
Line Cord
To Single-Line
Telephone Jack
(RJ11C)
Computer
Fax
Modem
DATA
TS620bk01.book Page 11 Wednesday, June 14, 2006 2:18 PM

12
Settings
Programming Summary
You can program the following functions. The display shows the programming
instructions. See the corresponding pages for function details.
Make sure that the handset is on the cradle, the AC adaptor is connected and
the SP-PHONE/HEADSET indicator light is off.
During programming
* To select a desired function item, scroll through the items by pressing {4}or {3}. Then
press {OK}to go to the next step.
•“––––––––––––––––”indicates the end of the function menu.
• You can exit the programming mode any time by pressing {EXIT}.
• If you do not press any buttons for 60 seconds, the unit will exit the programming mode.
Press {FUNCTION/EDIT}.
<Function menu>*
Save phonebook ? To store names and phone numbers in memory
. .
Save M1,M2,M3 ? (p. 33, 38).
Program ?
Set answering ?. . . To program answering system functions (p. 19).
Set clock ? . . . . . . . To adjust the time and date (p. 13).
Change language? . To select the display language (p. 14).
––––––––––––––––
<Function menu>*
Change password? . To change the password for the call restriction (p. 45).
Call restrict ?. . . To set the call restriction feature (p. 46).
Set flash time ? . To select the flash time (p. 44).
Set dial mode ?. . . To select the dialing mode (p. 15).
LCD contrast ?. . . . To select the LCD contrast (p. 15).
Set hold music ? . To set the music during hold (p. 43).
C.WTG options ?. . . To select Call Waiting Deluxe (p. 26).
Time adjustment? . To set the auto time adjustment (p. 16).
––––––––––––––––
Scroll to “Program ?” by pressing {4}or {3}and press {OK}(Yes key).
TS620bk01.book Page 12 Wednesday, June 14, 2006 2:18 PM

13
Settings
Time and Date
You can select AM/PM or 24-hour clock
by programming.
Make sure that the handset is on the
cradle, the AC adaptor is connected
and the SP-PHONE/HEADSET
indicator light is off.
1Press {FUNCTION/EDIT}.
2Scroll to “Set clock ?” by
pressing {4}or {3}and press
{OK}(Yes key).
3Press {OK}(Next key).
Enter the current year.
(Example: To set 2006, enter
“06”.)
• You can set the year 2000 to 2099.
4Press {OK}(Next key).
5Enter the current time (hour and
minute) using a 4-digit number.
(Example: To set 9:30, enter
“0930”.)
• For AM/PM setting: Enter numbers
between 0100 and 1259.
• For 24-hour clock: Enter numbers
between 0000 and 2359.
6Press {OK}(Next key).
• If numbers between 0000 and
0059, or 1300 and 2359 are
entered, the time will automatically
be set using the 24-hour clock. Go
to the step 9.
7Press {#}to select “AM”, “PM” or
24-hour clock.
• Each time you press {#}, the
selection will change on the
display.
8Press {OK}(Next key).
9Enter the current month and day
using a 4-digit number.
(Example: To set Dec. 27, enter
“1227”.)
Voice Time/Day Stamp:
During playback, a synthesized voice will
announce the time and day that each
message was recorded.
Enter year
 [OK]=Next
2 6
9:3
 [OK]=Next
Enter time
#=AM/PM / 24H
AM
 [OK]=Next
Option
Display
PM
AM
AM
PM
24H 24-hour clock
Enter month/day
12/27
[OK]=Save
TS620bk01.book Page 13 Wednesday, June 14, 2006 2:18 PM

14
Settings
10 Press {OK}(Save key).
• A long beep sounds.
• The clock starts working.
• The display will return to step 2. To
exit the programming mode, press
{EXIT}or wait for 60 seconds.
• You can go back to the previous screen by
pressing {3}, when setting the time and
date (steps 3 through 9).
• If 3 beeps sound when entering the time
and date, the time and date entered are
not correct. Enter the correct time and
date.
Display Language
You can select either “English” or
“French” as the display language.
Your phone comes from the factory set
to “English”.
Make sure that the handset is on the
cradle, the AC adaptor is connected
and the SP-PHONE/HEADSET
indicator light is off.
1Press {FUNCTION/EDIT}.
2Scroll to “Change language?”
by pressing {4}or {3}.
3Press {OK}(Yes key).
4Select “English” or
“ Français ”
by pressing {4}or {3}.
5Press {OK}(Save key).
• A long beep sounds.
• The display will return to step 2. To
exit the programming mode, press
{EXIT}or wait for 60 seconds.
• You can exit the programming mode any
time by pressing {EXIT}.
• The clock setting will automatically change
to 24-hour format if you set the LCD
display language to “French”.
After recover from power failure, “ ” will
flash. Readjust the time and date.
For Call Display service users
(p. 25)
If a time display service is available with
the Call Display service:
• The Call Display information will re-set
the clock after the ring if the adjusted
time and/or date is incorrect and the
Time Adjustment set to ON (p. 16). If the
time/date has not previously been set,
the Call Display information will not
adjust the clock.
Language
:English

[OK]=Save
TS620bk01.book Page 14 Wednesday, June 14, 2006 2:18 PM

15
Settings
Dialing Mode
If you have touch tone service, set to
Tone. If rotary or pulse service is used,
set to Pulse. Your phone default setting
is Tone.
Make sure that the handset is on the
cradle, the AC adaptor is connected
and the SP-PHONE/HEADSET
indicator light is off.
1Press {FUNCTION/EDIT}.
2Scroll to “Program ?” by
pressing {4}or {3}and press
{OK}(Yes key).
3Scroll to “Set dial mode ?”
by pressing {4}or {3}and
press {OK}(Yes key).
4Select “Pulse” or “Tone” by
pressing {4}or {3}.
(Example: “Tone” is selected.)
5Press {OK}(Save key).
• A long beep sounds.
• The display will return to step 3. To
exit the programming mode, press
{EXIT}or wait for 60 seconds.
• You can exit the programming mode any
time by pressing {EXIT}.
LCD Contrast
You can select the LCD contrast level
from 1 to 4 by programming. To make
the display clearer, set to a high level.
Your phone default setting is 2.
Make sure that the handset is on the
cradle, the AC adaptor is connected
and the SP-PHONE/HEADSET
indicator light is off.
1Press {FUNCTION/EDIT}.
2Scroll to “Program ?” by
pressing {4}or {3}and press
{OK}(Yes key).
3Scroll to “LCD contrast ?” by
pressing {4}or {3}and press
{OK}(Yes key).
• The current setting is displayed.
4Select the desired contrast by
pressing {4}or {3}, then press
{OK}(Save key).
• A long beep sounds.
• The display will return to step 3. To
exit the programming mode, press
{EXIT}or wait for 60 seconds.
• You can exit the programming mode any
time by pressing {EXIT}.
Dial mode
:Tone

[OK]=Save
Low !!!! High
 [OK]=Save
LCD contrast
TS620bk01.book Page 15 Wednesday, June 14, 2006 2:18 PM

16
Settings
Ringer Volume
Make sure that the AC adaptor is
connected and the unit is not being
used.
To select HIGH (default), MID or
LOW, press {HOLD/RINGER}.
• Each time you press the button, the ringer
volume will change and the selected
volume will ring.
To turn the ringer OFF, press and hold
{HOLD/RINGER}until 2 beeps sound.
•“ ”is displayed.
To turn the ringer ON, press {HOLD/
RINGER}.
• The ringer will sound at the HIGH level.
Time Adjustment (Call
Display subscribers only)
Using this feature, the unit’s date and
time setting will be automatically
adjusted when caller information is
received. You can set the auto time
adjustment by programming. Your
phone default setting is ON.
Make sure that the handset is on the
cradle, the AC adaptor is connected
and the SP-PHONE/HEADSET
indicator light is off.
1Press {FUNCTION/EDIT}.
2Scroll to “Program ?” by
pressing {4}or {3}and press
{OK}(Yes key).
3Scroll to “Time adjustment?”
by pressing {4}or {3}and
press {OK}(Yes key).
4Select “On” or “Off” by pressing
{4}or {3}.
5Press {OK}(Save key).
• A long beep sounds.
• The display will return to step 3. To
exit the programming mode, press
{EXIT}or wait for 60 seconds.
• To use this feature, set the date
and time in advance (p. 13).
TS620bk01.book Page 16 Wednesday, June 14, 2006 2:18 PM

17
Greeting Message
You can record a personal greeting message of up to 1 minute. If a greeting
message is not recorded, one of the two pre-recorded greetings will be played
when a call is received (p. 18).
Make sure that the handset is on the cradle, the AC adaptor is connected and
the SP-PHONE/HEADSET indicator light is off.
To record a greeting message
1Press {GREETING REC}.
• The unit announces “To record greeting, press Record again”.
2Within 10 seconds, press {GREETING REC}again.
3After the long beep, talk clearly, about 20 cm
away from the MIC (microphone).
• The display will show the recording time.
• If you record for over 1 minute, the unit will
automatically stop recording.
All messages (incoming, etc.) are stored in flash memory (p. 18). The recording
time is about 15 minutes.
We recommend you record a brief greeting message (see sample on next
page) in order to leave more time for recording new messages.
To increase the volume,
press VOLUME {3}.
To decrease, press
VOLUME {4}.
{GREETING REC}
{STOP}
{ERASE}
{SP-PHONE/HEADSET}
MIC
{GREETING CHECK}
Greeting record
-3
Preparing the Answering System
TS620bk01.book Page 17 Wednesday, June 14, 2006 2:18 PM

18
Preparing the Answering System
4When finished, press {STOP}.
• After a few seconds, the display will change.
• If the unit starts to ring while recording a greeting message, press {SP-PHONE/
HEADSET}or lift the handset off the unit to answer the call. The recording will stop.
Start again from the beginning after hanging up.
To check the recorded greeting message
Press {GREETING CHECK}.
• The greeting message will be played.
To erase the recorded greeting message
Press {GREETING CHECK}, and then press {ERASE}while the message is
being played.
• The unit will answer a call with a pre-recorded greeting.
Pre-recorded greeting message
If you do not record a greeting message (p. 17), one of two messages will be
played when a call is received, depending on the caller’s recording time (p. 21).
To check the pre-recorded greeting, press {GREETING CHECK}.
A pre-recorded greeting will be played as follows:
∫When the recording time is set to “1 minute”, “2 minutes” or “3 minutes”:
“Hello, we are not available now. Please leave your name and phone number after the beep.
We will return your call.”
∫When the recording time is set to “Greeting only”:
“Hello, we are not available now. Please call again. Thank you for your call.”
Greeting message sample
“Hello, this is (your name and/or number). Sorry I cannot take your call. Please leave a
message after the beep. Thank you.”
Flash Memory Message Backup
Messages are stored indefinitely on a “flash memory” IC chip and will not be
affected by power failures. All messages are saved until you erase them.
TS620bk01.book Page 18 Wednesday, June 14, 2006 2:18 PM

19
Preparing the Answering System
Programming Summary for the Answering System
You can program the following functions. The display shows the programming
instructions. See the corresponding pages for function details.
Make sure that the handset is on the cradle, the AC adaptor is connected and
the SP-PHONE/HEADSET indicator light is off.
During programming
* To select a desired function item, scroll through the items by pressing {4}or {3}. Then
press {OK}(Yes key) to go to the next step.
•“––––––––––––––––”indicates the end of the function menu.
• You can exit the programming mode any time by pressing {EXIT}.
• If you do not press any buttons for 60 seconds, the unit will exit the programming mode.
Press {FUNCTION/EDIT}.
Scroll to “Set answering ?” by pressing {4}or {3}and press {OK}
(Yes key).
<Function menu>*
Remote code ? . . . . . . . . To set the remote code (p. 51).
Number of rings? . . . . . To select the number of rings (p. 20).
Recording time ? . . . . . To select the caller’s recording time (p. 21).
Call screening ? . . . . . To set the call screening feature (p. 21).
––––––––––––––––
TS620bk01.book Page 19 Wednesday, June 14, 2006 2:18 PM

20
Preparing the Answering System
Number of Rings
You can select the number of times the
unit rings before the answering system
answers a call, from “2” to “7” or “Toll
saver*”. Your phone default setting is
“4”.
Make sure that the handset is on the
cradle, the AC adaptor is connected
and the SP-PHONE/HEADSET
indicator light is off.
1Press {FUNCTION/EDIT}.
2Scroll to “Set answering ?”
by pressing {4}or {3}, then
press {OK}(Yes key).
3Scroll to “Number of rings?”
by pressing {4}or {3}.
4Press {OK}(Yes key).
• The current setting is displayed.
5Select the number of rings by
pressing {4}or {3}.
• You can also select the number of
rings by pressing dialing buttons
{2}to {7}or {0}(Toll saver*).
6Press {OK}(Save key).
• A long beep sounds.
• The display will return to step 3. To
exit the programming mode, press
{EXIT}or wait for 60 seconds.
• You can exit the programming mode any
time by pressing {EXIT}.
Number of rings
:4

[OK]=Save
* Toll Saver
When you call the unit from a touch
tone telephone:
If the unit answers on the 2nd ring,
there is at least one new message.
If the unit answers on the 4th ring,
there are no new messages.
Hang up when you hear the 3rd
ring. This will save you the toll charge
for the call.
TS620bk01.book Page 20 Wednesday, June 14, 2006 2:18 PM