Panasonic AWPH360N - PAN/TILT HEAD User manual

屋内回転台
取扱説明書
AW-PH360N
保証書は、必ず「お買い上げ日・販売店名」等の記入をお確
かめのうえ、お受け取りください。
製造番号は、品質管理上重要なものです。お買い上げの際は、
製品本体と保証書の製造番号をお確かめください。
保証書別添付
ご使用前にこの取扱説明書をよくお読みのうえ、正しくお使いください。
そのあと大切に保管し、わからないときは再読してください。
F0505Y0@VQTB0085
Indoor Pan/Tilt Head
AW-PH360N
Before attempting to connect, operate or adjust this product,
please read these instructions completely.
Printed in Japan
F0505Y0 VQTB0085
D

2
O上下190度、水平300度の回転ができる、
据え付け型の小型回転台です。
Oカメラとレンズ合わせて、総重量4㎏まで
搭載できます。
OコントローラーAW-RP301、AW-RP305、
AW-RP501、AW-RP505、AW-RP605A、
AW-RP400、パーソナルコンピューター
でコントロールできます。
O最大50ポジションの撮影する位置と設定
を、プリセットメモリーとして登録できま
す。
カメラケーブル ........................................ 1本
回転アーム ................................................ 1組
回転アーム取付ねじ
M4×12mm ..................................... 4本
落下防止用のチェ−ン ............................. 1本
チェーン取付ねじ
(平ワッシャー／スプリングワッシャー付き)
M4×8mm .................................... 1本
M4×6mm .................................... 1本
M2.6×6mm................................. 1本
概要 ............................................................... 2
付属品 ........................................................... 2
安全上のご注意 ............................................ 3
設置上のお願い ............................................ 6
使用上のご注意 ............................................ 7
各部の名前と働き ........................................ 8
取り付けかた ............................................. 10
■回転台の組み立て ............................. 10
■
コントローラー選択スイッチ・設置方向
スイッチ・ランディング特性の設定
...... 11
■伝送信号選択の設定 .......................... 12
■
映像信号のケーブル補償回路の設定 ... 13
■回転台の設置 ...................................... 14
■カメラの取り付け .............................. 15
接続のしかた .............................................. 19
■コネクターパネルの接続 ................... 19
■回転ヘッドコネクターパネル ........... 24
■台座コネクターリアパネルと
台座コネクターフロントパネル ....... 25
■回転台用ACアダプターとの接続 ..... 27
■接続例 .................................................. 28
リミッターについて ...................................44
■リミッターの設定／解除のしかた ... 45
消耗品の交換 .............................................. 48
保証とアフターサービス .......................... 49
定格 ............................................................. 50
目 次
概 要
付属品
- 2 -
1indicates safety information.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(service) instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND
ANNOYING INTERFERENCE, USE THE RECOMMENDED
ACCESSORIES ONLY.
CAUTION:
TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER
CHANGE OF SWITCH SETTING INSIDE THE UNIT TO QUALIFIED
SERVICE PERSONNEL.
WARNING:
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY.

- 3 -
1indicates safety information.
FCC Note:
This device complies with Part 15 of the FCC Rules. To assure continued
compliance follow the attached installation instructions and do not make any
unauthorized modifications.
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Replace battery with part No. CR2032 only.
Use of another battery may present a risk of fire or explosion.
Caution—Battery may explode if mistreated.
Do not recharge, disassemble or dispose of in fire.

- 4 -
OThis is a compact stand-alone type of
pan/tilt head which is capable of rotating
95 degrees upward and downward and
300 degrees on the horizontal.
OThis pan/tilt head can bear a total weight
of up to 8.8 lb (4 kg) for the camera and
lens combined.
OThe pan/tilt head can be controlled using
the controllers AW-RP301, AW-RP305,
AW-RP501, AW-RP505, AW-RP605A,
AW-RP400 or a personal computer.
OThe positions and settings for shooting
up to 50 points can be entered as data
into the preset memory.
Camera cable .................................... (!1)
Tilting arm ......................................... (!1)
Tilting arm fixing screws
M4!12 mm ................................... (!4)
Safety chain ...................................... (!1)
Chain attachment screws
(with flat and spring washers)
M4!8 mm ..................................... (!1)
M4!6 mm ..................................... (!1)
M2.6!6 mm .................................. (!1)
Please check the following accessories have been provided.
Introduction ........................................... 4
Accessories ........................................... 4
Installation precautions ........................ 5
Precautions for use .............................. 6
Parts and their functions ...................... 7
Installation ............................................. 9
$Assembling the pan/tilt head ............ 9
$Controller selection switch / installation
direction switch /
landing characteristics settings . 10
$Transmission signal
selection setting .......................... 11
$Setting the cable compensation
circuit of video signals ............... 12
$Installing the pan/tilt head .............. 13
$Mounting the camera ..................... 14
Connections ........................................ 18
$Connecting the connector panel .... 18
$Head connector panel .................... 23
$Connecting the base connector
rear panel and the base
connector front panel ................. 24
$Connecting the AC adapter for use
with the pan/tilt head ................. 26
$Connection examples .................... 27
Limiters ................................................ 43
$Setting/releasing the limiters .......... 44
Replacement of consumable parts ... 47
Specifications ...................................... 48
Contents
Introduction
Accessories

- 5 -
ODo not install the pan/tilt head on any of its sides.
OAvoid using the pan/tilt head in kitchens or other places where there is excessive steam
and oil fumes.
OMake sure that the installation of the pan/tilt head has been completed before mounting
the camera onto it.
OThis pan/tilt head has a maximum load capacity of 8.8 lb (4 kg).
Do not use it for loads over 8.8 lb (4 kg).
ODo not use a lens that will cause the camera to be poorly balanced. Such a lens should
not be used even if the load capacity is under 8.8 lb (4 kg).
ODo not install the pan/tilt head outdoors or in any place where the temperature is over
113°F (45°C) or below 14°F (–10°C).
Further, it should be used where the ambient humidity is less than 90%.
OScrews for mounting the pan/tilt head are not provided with the stand and must therefore
be purchased separately.
They should be selected with due consideration given to the location where the pan/tilt
head is to be mounted and its load capacity.
OTo supply power to the pan/tilt head, use only the AC adapter (AW-PS300A) designed
for use with this pan/tilt head. The pan/tilt head cannot be powered by batteries or any
other source of power.
OWhen handling the pan/tilt head, be sure to hold it by the base.
Do not lift the pan/tilt head by the head or tilting arm.
Doing so may cause the unit to malfunction.
ODo not turn the head or tilting arm by hand.
Doing so may cause the unit to malfunction.
ODropping the pan/tilt head or subjecting it to a strong shock may cause malfunctioning or
an accident.
OInstall the pan/tilt head so that a clearance of at least 3.3 ft. (1 m) is left around the
monitor.
OWhen mounting a camera onto the pan/tilt head, take due care to prevent the camera
from slipping out of position or dropping.
OInstall the pan/tilt head and set the limiters so as to ensure that none of the components
mounted on the pan/tilt head or cables will make contact with any other objects in the
vicinity when the pan/tilt head rotates.
Installation precautions

- 6 -
Precautions for use
OIn order to protect the environment when the pan/tilt head is to be discarded at the end
of its service life, ask a specialized contractor to dispose of it properly.
OThis pan/tilt head uses a manganese dioxide-lithium battery (CR2032).
Be absolutely sure to remove this battery when disposing of the pan/tilt head or printed
circuit boards.
Be sure to dispose of any batteries removed according to the applicable regulations of
the country concerned.
Do not dispose of this type of battery as household garbage.
For details on how to remove the battery, refer to the section on replacing the battery in
“Replacement of consumable parts” (page 47).
OTo prevent malfunction because of contact with any objects in the vicinity when the
pan/tilt head rotates, the unit is set to be shifted to the safe mode and the unit’s tally
lamp blinks if the overload to it happens.
In the safe mode, neither pan nor tilt operate.
To release the safe mode, turn off the power of the AC adapter connected to the pan/tilt
head to dissolve the overload, then turn on the power again.

- 7 -
Parts and their functions

- 8 -
Parts and their functions
1Tilting arm
This tilts in the vertical direction.
2Tilting arm fixing screws
M4!12 mm (4 screws supplied)
3Camera mounting plate
This is used to mount the convertible
camera.
4Guide screws
These are used to maintain the
camera’s balance and anchor the
camera mounting plate.
5Guide pin
This determines the mounting direction
of the camera.
6Guide roller
This serves as the fulcrum for
maintaining the camera’s balance.
7Camera mounting screws
(U1/4˝-20 UNC)
These are used to mount the camera
and anchor it securely.
8Head
This rotates in the horizontal direction.
9Tally lamps (!2)
These light (red) in response to the
selection signals.
:Head connector panel
This is used for connection with the
camera and lens.
;Base
<Pan/tilt head mounting holes
These four holes are used for mounting
the pan/tilt head.
=Safety wire mounting hole
This is used when attaching a wire to
prevent the pan/tilt head from dropping.
>Base connector rear panel
This is used for connection with a
controller, multi-port hub or AC adapter
for the pan/tilt head.
?Base connector front panel
This is used for connection with a
camera control or a personal computer.

- 9 -
Installation (The installation work must be performed by your dealer without fail.)
Stand-alone installationSuspended installation
Tilting Arm
$Assembling the pan/tilt head
Be absolutely sure to hold the pan/tilt head by the base when handling it.
OAttaching the tilting arm
Use the tilting arm fixing screws to attach the tilting arm. The way in which the arm is
mounted differs depending on the direction in which it is installed. (See the figure below.)
<Note>
Tighten up the screws securely to ensure that they will not come loose during use.

$Controller selection switch / installation direction switch /
landing characteristics settings
The following switches are set when determining controller selections, stand alone
settings and landing characteristics settings.
(RP501 / suspended installation / soft landing are the default settings.)
1. Remove the four head cover screws, and remove the cover slowly. (Take care not to
disturb the tally LED lamp wiring connections when removing the cover.)
2. Set the SW1, SW2 and SW4 switches on the front printed circuit board as follows.
For AW-RP301/AW-RP305/AW-RP501/AW-RP505/AW-RP400:
Set SW1 switch to its right-side position (RP501). (Factory setting)
For AW-RP605A:
Set SW1 switch to its left-side position (RP605).
For suspended installation:
Set SW2 to its left-side position (HANGING). (Factory setting)
For stand-alone installation:
Set SW2 to its right-side position (DESKTOP).
For a soft landing:
Set SW4 switch No.4 to its top position (ON). (Factory setting)
For a precise landing:
Set SW4 switch No.4 to its bottom position (OFF).
3. Upon completion of the settings, return the head cover to its original position, and
secure it with the screws (while taking care not to pinch the wires).
<Notes>
OBefore setting the switches, make absolutely sure that the power of the AC adapter
which is to be connected to the pan/tilt head is set to OFF.
OThe controller selection and landing characteristics are not changed simply by selecting
the switch positions. They are changed only after the power is turned off and back on
again after the switches have been set.
- 10 -
Installation (The installation work must be performed by your dealer without fail.)
Suspension
Do not change the setting of this
switch — use it at the RS-422
position.
Stand-alone
RS-422 RS-232C
RP605 RP501