Panasonic LUMIX S Pro R70200 User manual

18 DVQX1725
Operating Instructions
INTERCHANGEABLE LENS
FOR DIGITAL CAMERA
Thank you for purchasing Panasonic product.
Please read these instructions carefully before using this
product, and save this manual for future use.
This lens can be attached to a 35 mm digital camera that
complies with the Leica Camera AG L-Mount standard
and that is equipped with a full-frame image sensor.
0L-Mount is a trademark or registered trademark of
Leica Camera AG.
0Other names, company names, product names
mentioned in this document are trademarks or
registered trademarks of the companies concerned.
Information for Your Safety .................................... 19
Precautions ............................................................ 20
Supplied Accessories............................................. 21
Names and Functions of Components................... 22
Attaching the Lens ................................................. 23
Switching AF/MF.................................................... 24
Using the Tripod Mount..........................................24
Cautions for Use .................................................... 26
Troubleshooting ..................................................... 26
Specifications......................................................... 27
Limited Warranty (ONLY FOR U.S.A.)................... 28
Limited Warranty (ONLY FOR CANADA) .............. 30
Contents
S-R70200-DVQX1725ZA.book 18 ページ ２０１９年１月２９日 火曜日 午後６時５５分

19
DVQX1725
English
Information for Your Safety
Keep the unit as far away as possible from electromagnetic
equipment (such as microwave ovens, TVs, video games,
radio transmitters, high-voltage lines etc.).
0 Do not use the camera near cell phones because doing so may
result in noise adversely affecting the pictures and sound.
0If the camera is adversely affected by electromagnetic
equipment and stops functioning properly, turn the
camera off and remove the battery and/or the
connected AC adaptor. Then reinsert the battery and/or
reconnect the AC adaptor and turn the camera on.
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
0Reorient or relocate the receiving antenna.
0Increase the separation between the equipment and
receiver.
0Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
0Consult the dealer or an experienced radio/TV
technician for help.
Any unauthorized changes or modifications to this equipment
would void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
Supplier’s Declaration of Conformity
Trade Name: Panasonic
Model No.: S-R70200
Responsible Party:
Panasonic Corporation of North America
Two Riverfront Plaza, Newark, NJ
07102-5490
Support Contact: http://shop.panasonic.com/support
THE FOLLOWING APPLIES ONLY IN CANADA.
CAN ICES-3(B)/NMB-3(B)
S-R70200-DVQX1725ZA.book 19 ページ ２０１９年１月２９日 火曜日 午後６時５５分

20 DVQX1725
-If you see this symbol-
Precautions
∫Lens care
0Do not subject to strong vibration, shock, or
pressure. These may cause malfunction or
damage.
– Don’t press hard on the lens.
0 Take care not to drop or bump the lens when carrying it.
– When carrying the digital camera with the lens
attached, hold both the lens and the digital camera to
carry them.
– Take care not to drop or bump the bag in which you have put
the lens.
0 When there is dirt (water, oil, and fingerprints, etc.) on the
surface of the lens, the images may be affected. Lightly wipe
the surface of the lens with a soft, dry cloth before and after
recording.
0When the lens is not in use, be sure to attach the lens
cap and lens rear cap to prevent dust and other
particles from accumulating on or entering the lens.
0To protect the lens contact
points (A), do not do the
following. These may
cause malfunction.
– Touch the lens contact
points.
– Allow the lens contact
points to become dirty.
– Place the lens with its
mount surface facing
down.
∫Dust and splash resistant
0The dust and splash resistant of the camera will
not prevent the entry of dust or water droplets
completely. Take the following precautions to
provide satisfactory dust and splash resistant
performance. If the lens is not working properly,
consult the dealer or your nearest Service Center.
Disposal of Old Equipment
Only for European Union and countries with recycling
systems
This symbol on the products, packaging,
and/or accompanying documents means
that used electrical and electronic products
must not be mixed with general household
waste.
For proper treatment, recovery and recycling
of old products, please take them to
applicable collection points in accordance with your
national legislation.
By disposing of them correctly, you will help to save
valuable resources and prevent any potential negative
effects on human health and the environment.
For more information about collection and recycling,
please contact your local authority.
Penalties may be applicable for incorrect disposal of
this waste, in accordance with national legislation.
S-R70200-DVQX1725ZA.book 20 ページ ２０１９年１月２９日 火曜日 午後６時５５分

21
DVQX1725
English
– Attach to attach a digital camera that is dust and
splash resistant.
– When attaching or removing the lens, be careful so
that foreign objects such as sand, dust, and water
droplets do not adhere to or enter the lens mount
rubber, contact points, digital camera and lens.
– If the lens is exposed to water droplets or other
liquids, wipe them off with a soft, dry cloth.
0To improve the dust and splash resistant performance
of the lens, a lens mount rubber is used in the mount.
– The lens mount rubber will leave scuff marks on the
digital camera mount, but this does not impact
performance.
– For information on changing the lens mount rubber,
contact your nearest Service Center.
∫Condensation (when the lens is fogged up)
0Condensation occurs when the ambient temperature or
humidity changes. Please be careful, as it may cause
lens stains, mold and malfunction.
0If condensation occurs, turn off the digital camera and
leave it for approx. 2 hours. The fog will disappear
naturally when the temperature of the digital camera
becomes close to the ambient temperature.
0The appearance and specifications of products
described in this document may differ from the actual
products you have purchased due to later
enhancements.
Supplied Accessories
Product numbers correct as of January 2019. These may
be subject to change.
¢Fitted to the lens at the time of purchase.
1 Lens pouch
2 Lens hood
3 Lens cap¢
4 Lens rear cap¢
5 Tripod mount¢
SFC0360 DVZE1035Z
2134
1GE1Z276Z
5
DVYE1130Z
RGE1Z276Z
S-R70200-DVQX1725ZA.book 21 ページ ２０１９年１月２９日 火曜日 午後６時５５分

22 DVQX1725
Names and Functions of
Components
1Lens surface
2Focus ring
Switches between AF (auto focus) and MF (manual
focus) by sliding the focus ring forwards or
backwards. (l 24)
Rotates the focus ring to focus when set to MF.
3Zoom ring
Zooms to telephoto or wide-angle.
4Tripod mount (l 24)
5Tripod mount locking knob
6O.I.S. switch
The stabilizer function is set to activate if the O.I.S.
switch is set to [ON].
0We recommend setting the O.I.S. switch to [OFF]
when using a tripod.
7Contact points
8Lens fitting mark
9Lens mount rubber
Note
0There may be differences in focus when you use zoom
after focusing. Focus again.
0If the sound of AF operation and stabilizer operation
bothers you during video recording, it is recommended
to record as follows:
– Slide the focus ring to the MF side to record.
– Set the O.I.S. switch to [OFF] and use a tripod to
record.
1
8
9
23456
7
S-R70200-DVQX1725ZA.book 22 ページ ２０１９年１月２９日 火曜日 午後６時５５分

23
DVQX1725
English
Attaching the Lens
For information on how to attach the lens, refer to the
operating instructions for your digital camera.
0Attach the lens after turning off the digital camera.
0Attach the lens after removing
the lens rear cap.
0 After removing the lens from the
digital camera, be sure to attach
the lens cap and lens rear cap to
prevent dust and other particles
from accumulating on or entering
the lens.
∫Attaching the lens hood
1Align mark A ( ) on
the lens hood with the
mark on the tip of the
lens.
2Rotate the lens hood in
the direction of the
arrow to align mark B
( ) on the lens hood
with the mark on the tip
of the lens.
0Attach the lens hood by
rotating it until it clicks.
∫Removing the lens hood
While pressing the lens
hood button, rotate the
lens hood in the direction
of the arrow and then
remove it.
Note
0When carrying, the lens hood can be attached in the
reverse direction.
1Remove the lens hood.
2Align mark C ( ) on the lens hood with the mark
on the tip of the lens.
3Attach the lens hood by rotating it in the direction of
the arrow until it clicks.
0It is recommended to remove the lens hood during
flash photography as the lens hood can block the light
from the flash.
0To prevent dropping of the lens, you should never carry
the lens by just holding the lens hood.







S-R70200-DVQX1725ZA.book 23 ページ ２０１９年１月２９日 火曜日 午後６時５５分

24 DVQX1725
∫Notes on filter use
0It is possible to attach the lens cap or the lens hood
with the filter already attached.
0If you use two or more filters at the same time, part of a
recorded image may darken.
0It is not possible to attach any items other than filters
such as a conversion lens or adaptor to the front of the
lens and use it in combination with this lens.
Lens damage may result if such items are attached.
Switching AF/MF
Switch AF/MF by sliding the
focus ring
A forwards or
backwards (focus clutch
mechanism).
0When the digital camera is
set to MF, the operation will
be MF irrespective of the
position of the focus ring.
0 Check the length indication B
when using MF. Use it as a guide
for focusing.
0 You can set the amount that
the focus moves with the focus
ring using menu settings in
compatible digital cameras.
Switch the lens to AF and set
the digital camera to MF. Refer to the operating
instructions for the digital camera for details.
Using the Tripod Mount
When using a tripod, attach it
to the tripod mount of the
lens.
0When a tripod is attached to
the tripod mount of the
digital camera, damage to
the lens may result when
carrying.
∫Changing the vertical/horizontal orientation
This way, you can quickly switch between the vertical
and horizontal orientation of the digital camera while the
tripod is in use.
1Rotate the tripod mount
locking knob in the
direction indicated by the
arrow to loosen.
AF MF

3.1
0.92 1.2 1.5 2.2 4 10 ĩm
45 7 1328 ft

S-R70200-DVQX1725ZA.book 24 ページ ２０１９年１月２９日 火曜日 午後６時５５分

25
DVQX1725
English
2Rotate the digital
camera and lens to
change the position.
3Rotate the tripod
mount locking knob in the
direction indicated by the
arrow to tighten firmly.
∫Detaching the tripod mount
1Rotate the tripod
mount locking knob in
the direction indicated
by the arrow to loosen.
2Match the marks on the
tripod mount and the
tripod mount locking
knob.
3While pulling out the
tripod mount locking
knob, open and remove
the tripod mount.
0When detaching the
tripod mount, support the
lens and digital camera
to ensure they do not fall.
∫Attaching the tripod mount
Attach by reversing the steps used to detach.
0Match the marks on the
tripod mount and the
lens.
0When attaching the
tripod mount, pull out the
tripod mount locking
knob first and then close
the tripod mount.
0Be careful not to pinch
your fingers between the
tripod mount and the lens.
S-R70200-DVQX1725ZA.book 25 ページ ２０１９年１月２９日 火曜日 午後６時５５分

26 DVQX1725
Cautions for Use
0Do not spray the lens with insecticides or volatile
chemicals.
– If such substances get onto the lens they can
damage the exterior case or cause the paint to peel.
0Do not point the lens at the sun or other strong
light sources.
– This may cause the lens to collect an excessive
amount of light, resulting in fire and malfunction.
0Do not use while directly touching the lens at low
temperatures for a long period of time.
– In cold places (environments below 0 oC (32 oF), such
as ski slopes), prolonged direct contact with the metal
parts of the lens may cause skin injury. Use gloves or
similar when using the lens for long periods.
0Use a soft, dry, dust-free cloth to clean the lens.
– Do not use benzine, thinner, alcohol or other similar
cleaning agents to clean the lens. Using solvents
may damage the lens or cause the paint to peel.
– Do not use a household detergent or a chemically
treated cloth.
0Do not keep products made of rubber, PVC or similar
materials in contact with the lens for a long period of
time.
0Do not disassemble or alter this product.
0When the lens is not going to be used for a prolonged
period, we recommend storing with a desiccant (silica
gel).
0Check all the parts before recording when you have not
used the lens for a long period of time.
0Avoid using or storing the lens in any of the following
locations as this may cause problems in operation or
malfunctioning:
– In direct sunlight or on a beach in summer
– In locations with high temperatures and humidity
levels or severe changes in temperature and
humidity
– In sandy or dusty locations
– Where there is fire
– Near heaters, air conditioners or humidifiers
– Where water may make the lens wet
– Where there is vibration
– Inside a vehicle
0Refer also to the operating instructions for the digital
camera.
Troubleshooting
A rattling sound, etc. is heard when the digital
camera is turned on or off or the lens is shaken.
There is a sound from the lens when taking pictures.
0This is the sound of the lens moving and aperture
operation. It is not a malfunction.
S-R70200-DVQX1725ZA.book 26 ページ ２０１９年１月２９日 火曜日 午後６時５５分

27
DVQX1725
English
Specifications
The specifications are subject to change for performance enhancement.
INTERCHANGEABLE LENS FOR DIGITAL CAMERA “LUMIX S PRO 70-200 mm F4 O.I.S.”
Mount Leica Camera AG L-Mount
Focal length f=70 mm to 200 mm
Lens construction 23 elements in 17 groups (1 aspherical lens, 1 UED lens, 3 ED lenses, 1 UHR lens)
Aperture type 9 diaphragm blades/Circular aperture diaphragm
Maximum aperture F4.0
Minimum aperture value F22
Angle of view 34x (Wide) to 12o (Tele)
Recording range 0.92 m (3.02 feet) to ¶ (from the focus distance reference line)
Maximum image
magnification 0.25k
Image stabilizer Yes
Filter diameter 77 mm
Maximum diameter ‰84.4 mm (3.3q)
Overall length Approx. 179 mm (7.0 q ) (from the tip of the lens to the base side of the lens mount)
Mass (Weight) Approx. 985 g (2.17 lb) (excluding the external tripod mount)
Dust and splash resistant Yes
Recommended operating
temperature j10 oC to 40 oC (14 oF to 104 oF)
Permissible relative
humidity 10%RH to 80%RH
S-R70200-DVQX1725ZA.book 27 ページ ２０１９年１月２９日 火曜日 午後６時５５分