Panasonic KX-TG2770S User manual

2.4GHz Expandable Cordless Phone System
Model No. KX-TG2770S
Pulse-or-tone-dialing capability
Operating Instructions
Charge the battery for about 15 hours before initial use.
PLEASE READ BEFORE USE AND SAVE.
Contents:
Location of Controls 2
Connections 5
Battery Installation/Battery Charge 6
Recording a Greeting Message 7
Making/Answering calls with the Cordless Handset 8
Making/Answering calls with the Base Unit 9
Caller ID Service 9
Automatic Answering Operation 10
Listening to Messages 10
Important Safety Instructions 11
FCC and Other Information 13

–2–
Please read IMPORTANT SAFETY
INSTRUCTIONS on page 11 before use.
Read and understand all instructions.
Location of Controls
■Cordless handset
INTERCOM
TRANSFER
CLEAR
SP-PHONE
HOLD
FUNCTION
REDIAL
CALLWAIT
2
1
3
4
5
6
78
TONE
0
9
CONF
TALK
OFF
FLASH
PAUS E
Back side
Speaker
Headset Jack
(*) (TONE) Button
(TALK) Button
(Speakerphone)
Button
Button
Microphone
Charge Contacts
Antenna
Display
(OFF) Button
(HOLD/CLEAR)
(INTERCOM/TRANSFER)
Button
(PAUSE/REDIAL)
Button
Soft Keys
Navigator Key
( , , , )
( FLASH/CALL!WAIT ) Button
CONF (Conference)/FUNCTION

–3–
■Base unit
21 3
STOP STOP
MAILBOX
MAILBOX
ERASE ERASE
MIC
PL
PLAYBACKSLOWTALK
YBACK SLOW TALK
MUTE
MUTE
PRIVPRIVACYACY
DIG ITALS
L SP
P
-PHONE
FUNCTION FUNCTION
EDITEDIT
FL FLASH
SH
CALL
CALL WAI
AIT
REDIAL
REDIAL PAUSE
AUSE
LOCATOR
LOCATOR
INTERCOM
INTERCOM
TRANSFER
TRANSFER
HOLD
HOLD
CONF
CONF
MEMO MEMO
GREETING
GREETING
KX-TG
TG2770
Display
MIC (Microphone)
(DIGITAL!SP-PHONE)
(Speakerphone)
Button and Indicator
(MUTE) Button and Indicator
(FLASH/CALL!WAIT) Button
(REDIAL/PAUSE) Button
(LOCATOR/INTERCOM)
(TRANSFER) Button
and Indicator
(PRIVACY) Button
(HOLD) Button
Button
(ERASE) Button
(STOP) Button
(GREETING)
Button
(ANSWER!ON)
Button and
Indicator
(MEMO)
Button
Antenna
(*) (TONE) Button MAILBOX
Buttons
(FUNCTION/EDIT)
Button
Antenna
CONF (Conference)/FUNCTION
Navigator Key (F, G, I, H)

–4–
■Charger unit
CHARGE
CHARGE Indicator
AC Adaptor
Charge Contacts

–5–
Connections
■Base unit
•USE ONLY WITH Panasonic AC ADAPTOR.
•The AC adaptor must remain connected at all times. (It is normal for the
adaptor to feel warm during use.)
Handset
Handset
Cord
Raise the antennas.
Telephone Line Cord
Power Outlet (AC 120 V, 60 Hz)
Fasten the AC adaptor cord.
Single-Line Telephone Jack (RJ11C)
Hook
AC
Adaptor
Power Outlet
(AC 120 V, 60 Hz)
AC Adaptor
CHARGEGE
• USE ONLY WITH Panasonic AC ADAPTOR KX-TCA1 (Order No. KX-TCA1-G).
•The AC adaptor must remain connected at all times. (It is normal for the
adaptor to feel warm during use.)
■Charger unit

–6–
Battery Installation/Battery Charge
■Recharge
Recharge the battery when:
–"Recharge battery" is displayed,
–" " flashes on the display, or
–the cordless handset beeps intermittently while it is in use.
•Clean the handset and the base unit charge contacts with a soft, dry
cloth once a month. Clean more often if the unit is subject to grease,
dust or high humidity. If not, the battery may not charge properly.
•If the battery is fully charged, you do not have to place the handset on the
charger until "Recharge battery" is displayed and/or " " flashes. This
will maximize the battery life.
•The battery cannot be overcharged.
■Battery installation
1 Install the battery in the cordless handset.
2 Close the handset cover.
■Battery charge
To power the cordless handset, charge the battery.
Place the cordless handset on the charger for about 15 hours before initial
use.
A nickel cadmium battery that is recyclable powers the product
you have purchased. At the end of its useful life, under various
state and local laws, it is illegal to dispose of this battery into
your municipal waste stream. Please call
1-800-8-BATTERY for information on how to recycle this
battery.

–7–
You can record a personal greeting message of up to 2 minutes. If a greeting
message is not recorded, one of two pre-recorded greetings will be played
when a call is received.
•All messages (greeting, incoming, etc.) are stored in digital memory. The
total recording time is about 15 minutes. We recommend you record a
brief greeting message in order to leave more time for recording new
messages.
1 Press and hold (GREETING) until a long beep is heard.
2 After the long beep, talk clearly, about 8 inches (20 cm) away from the MIC
(microphone).
3 When finished, press (GREETING).
•If you do not record a greeting message, one of two messages will be played
when a call is received, depending on the caller’s recording time.
Recording a Greeting Message

–8–
■To make a call
1 Press or .
2 Dial a telephone number.
3 To hang up, press (OFF) or place the handset on the charger.
•If "No link to base. Walk closer to base and try again" is
displayed and an alarm tone sounds in step 1, move closer to the base unit,
and try again.
•To redial the last number, press or , then press
(PAUSE/REDIAL).
•To adjust the handset volume/speaker volume:
To increase, press . To decrease, press .
•To put a call on hold, press (HOLD/CLEAR).
•To release the hold, press (HOLD/CLEAR).
■To answer a call
Press or .
Making/Answering Calls with the Cordless Handset

–9–
Making/Answering Calls with the Base Unit
■To make a call
1 Lift the handset off the cradle or press (DIGITAL!SP-PHONE).
2 Dial a telephone number.
3 Talk into the handset or the MIC (microphone).
4 To hang up, place the handset on the cradle or press (DIGITAL!SP-PHONE).
•To redial the last number, lift the handset off the cradle or press
(DIGITAL!SP-PHONE), and then press (REDIAL/PAUSE).
•To adjust the handset volume/speaker volume:
To increase, press . To decrease, press .
•To put a call on hold, press (HOLD).
•To release the hold:
—when using the speakerphone, press (DIGITAL!SP-PHONE) or lift the
handset.
—when using the handset, press (HOLD).
■To answer a call
Lift the handset off the cradle or press (DIGITAL!SP-PHONE).
Caller ID Service
This unit is compatible with a Caller ID service offered by your telephone
company.
After subscribing to a Caller ID service, the calling party’s information will be
displayed after the first ring.
The unit can record information of up to 50 different callers in the caller list.
The Caller List information is sorted from the most recent to the oldest call.
When the unit receives the 51st call, the oldest call is deleted.
If your unit is connected to a PBX system which does not support Caller ID
services, you cannot access those services. Please consult your equipment
supplier.

–10–
Automatic Answering Operation
■ How to use the mailboxes
The unit accommodates three mailboxes (Mailbox 1, 2 and 3). A caller can
leave a message in a specified mailbox. If a mailbox is not specified,
messages are recorded in the mailbox 1.
■ When a caller calls
The caller can select a mailbox by pressing (#) and (1) (Mailbox 1), pressing
(#) and (2) (Mailbox 2) or pressing (#) and (3) (Mailbox 3), while the greeting is
played. The caller can then record a message in the mailbox after a beep.
OR
The caller waits until the greeting finishes, and records a message after a
beep. The message will be recorded in the Mailbox 1.
■ Setting the unit to answer calls
Press (ANSWER!ON) to turn on the answering system.
•The indicator lights and “Answer set”is heard.
Listening to Messages
You can see the total number of recorded messages on the base unit display.
If the ANSWER ON indicator flashes and the mailbox icon(s) flash(es) on the
display, new messages have been recorded in the mailbox(es).
To listen to the messages, press (MAILBO !1), (MAILBO !2) or (MAILBO !3).
•When you have new messages, the unit announces the number of new
messages and plays them back.
•When you have no new messages, the unit plays back all recorded
messages.