Panasonic KX-TG7301MB User manual

PNQW1236ZA DC0608DN0 MB-2/3
Connections
Important:
LIf you use a telephone line cord which is not supplied, the unit may not work
properly.
(220-240 V AC, 50 Hz)
To telephone
line
DSL/ADSL filter
(For DSL/ADSL service
users) Hook
Guide
Plug
“Click”
Use only the supplied Panasonic
AC adaptor PQLV207CE.
Use only the supplied
telephone line cord.
Press plug firmly.
Plug
Guide
Do not try to connect over the guide.
Base unit
(KX-TG7302/KX-TG7303)
Charger
Use only the supplied Panasonic
AC adaptor PQLV209CE.
Press plug firmly.
(220-240 V AC, 50 Hz)
Hooks
Model No. KX-TG7301MB/KX-TG7302MB
KX-TG7303MB/KX-TG7321MB
Quick Guide
TG7301_7321MB(e)_QG.fm Page 1 Thursday, May 22, 2008 3:56 PM

– 2 –
Battery installation/Battery charge
Charge for about 7 hours.
Note:
LUSE ONLY Ni-MH batteries AAA (R03) size.
LDo NOT use Alkaline/Manganese/Ni-Cd batteries.
Operating tips
Using the navigator key
The handset navigator key can be used to
navigate through menus and to select items
shown on the display by pressing {^}, {V},
{<}, or {>}.
To adjust the receiver or speaker volume,
press {^} to increase the volume, or press {V}
to decrease the volume repeatedly while
talking.
Soft keys
The handset features 3 soft keys. By pressing
a soft key, you can select the feature shown
directly above it on the display.
Base unit
*1
Charger
*2
*1 Model shown is KX-TG7301.
*2 KX-TG7302/KX-TG7303
Rechargeable
Ni-MH ONLY
“Charging”will
be displayed.
{V}
{^}
Volume up
Volume down
{<}{>}
TG7301_7321MB(e)_QG.fm Page 2 Thursday, May 22, 2008 3:56 PM

– 3 –
Display language (Handset) (default: Hebrew)
1K(middle soft key)
2{V}/{^}: “”(“Handset Setup”) iM
3{V}/{^}: “”(“Display Setup”) iM
4{V}/{^}: “”(“Select Language”) iM
5{V}/{^}: Select your desired language. iMi{ih}
Note:
LIf you select a language you cannot read: {ih} iKi{^} 2 times iM
i{V} 2 times iM2 times i{V}/{^}: Select your desired language. i
Mi{ih}
Dialling mode (Handset) (default: Tone)
1K(middle soft key)
2{V}/{^}: “Base Unit Setup”iM
3{V}/{^}: “Dial Mode”iM
4{V}/{^}: Select the desired setting. iMi{ih}
Date and time (Handset)
1K(middle soft key)
2{V}/{^}: “Handset Setup”iM
3{V}/{^}: “Time Settings”iM
4{V}/{^}: “Set Date & Time”iM
5Enter the current date, month, and year.
6Enter the current hour and minute.
7Mi{ih}
Basic operations
Making/Answering calls (Handset)
Making calls Dial the phone number. i{C}/{s}
Answering calls {C}/{s}
To hang up {ih}
To adjust the receiver/
speaker volume
Press {^} or {V} repeatedly while talking.
Making a call using the redial
list
j(right soft key) i{V}/{^}: Select the desired
phone number. i{C}
Temporary tone dialling
(for rotary/pulse service
users)
1Make a call.
2Press {*} when prompted to enter your code or
PIN, then press the appropriate dial keys.
TG7301_7321MB(e)_QG.fm Page 3 Thursday, May 22, 2008 3:56 PM

– 4 –
Making/Answering calls (Handset)
Handset ringer volume 1K(middle soft key)
2{V}/{^}: “Handset Setup”iM
3{V}/{^}: “Ringer Setup”iM
4{V}/{^}: “Ringer Volume”iM
5{V}/{^}: Select the desired volume. iMi
{ih}
Phonebook (Handset)
Adding entries 1n(left soft key) iK
2{V}/{^}: “New Entry”iM
3Enter the party’s name (16 characters max.). i
M
4Enter the party’s phone number (24 digits max.).
iM2 times i{ih}
LTo enter a name, see the character table in the
operating instructions.
Making calls 1n(left soft key)
2{V}/{^}: Select the desired entry.
LYou can scroll through the phonebook entry by
pressing and holding {V} or {^}.
3{C}
Answering system (Base unit): KX-TG7321
Answering on/off Press {s}to turn on/off the answering system.
Listening to messages {6}
Frequently asked questions
Question Cause/solution
Why is wflashing? LThe handset is too far from the base unit. Move
closer.
LThe base unit’s AC adaptor is not connected.
Check the connections.
LYou are using the handset or base unit in an area
with high electrical interference. Place the base
unit and use the handset away from sources of
interference.
LThe handset is not registered to the base unit.
Register it (page 7).
Why can I not make calls? LThe dialling mode may be set incorrectly. Change
the setting (page 3).
Basic operations
TG7301_7321MB(e)_QG.fm Page 4 Thursday, May 22, 2008 3:56 PM

– 5 –
What should I do when the
handset does not turn on?
LMake sure the batteries are installed correctly.
LFully charge the batteries.
LClean the charge contacts and charge again.
How long is the battery
operating time?
LWhen you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 17 hours max.
Not in use (standby): 150 hours max.
LIt is normal for batteries not to reach full capacity
at the initial charge. Maximum battery
performance is reached after a few complete
cycles of charge/discharge (use).
LActual battery performance depends on a
combination of how often the handset is in use
and how often it is not in use (standby).
Can I keep the handset on
the base unit or charger
when I am not using it?
LEven after the handset is fully charged, the
handset can be left on the base unit or charger
without any ill effect on the batteries.
When should I replace the
batteries?
LIf the batteries are fully charged until 1 is
displayed, but
3 is displayed after a few calls,
replace the batteries with new ones.
What is a PIN? LThe PIN is a 4-digit number that must be entered
in order to change certain base unit settings. The
default PIN is “0000”.
What should I do to display
caller information?
LYou must subscribe to a Caller ID service. Contact
your service provider/telephone company for
details.
LThe message “You must first subscribe
to Caller ID.” will be displayed until you
receive caller information after subscribing to a
Caller ID service.
What should I do when noise
is heard, sound cuts in and
out?
LYou are using the handset or base unit in an area
with high electrical interference. Place the base
unit and use the handset away from sources of
interference.
LMove closer to the base unit.
LIf you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL filter between the base
unit and the telephone line jack. Contact your
DSL/ADSL provider for details.
Frequently asked questions
Question Cause/solution
TG7301_7321MB(e)_QG.fm Page 5 Thursday, May 22, 2008 3:56 PM

– 6 –
What should I do when the
operating time seems to be
shorter even after I fully
charged the batteries?
LClean the battery ends (S, T) and the charge
contacts with a dry cloth, and charge again.
What do I need to do to
erase y(Missed call) from
the display?
LThere are unviewed missed calls remaining. View
them using the following method.
1K(middle soft key)
2{V}/{^}: “Caller List”iM
3Press {V} to search from the most recent call, or
press {^} to search from the oldest call.
Frequently asked questions
Question Cause/solution
TG7301_7321MB(e)_QG.fm Page 6 Thursday, May 22, 2008 3:56 PM

– 7 –
Registering a handset to the base unit
The supplied handset and base unit are pre-registered. If for some reason the
handset is not registered to the base unit, register the handset.
1K(middle soft key)
2{V}/{^}: “Handset Setup”iM
3{V}/{^}: “Register H.set”iM
Proceed with the operation for your model.
NKX-TG7301/KX-TG7302/KX-TG7303
Press and hold {x} for about 5 seconds. (No
registration tone)
NKX-TG7321
Press and hold {x} for about 5 seconds, until
the registration tone sounds.
LThe next step should be completed within 90
seconds.
Wait until “Enter Base PIN”is displayed. i
Enter the base unit PIN (default: “0000”). i
M
LWhen the handset has been registered
successfully, wstops flashing.
Handset
M
Base unit
{x}
{x}
Handset
M
TG7301_7321MB(e)_QG.fm Page 7 Thursday, May 22, 2008 3:56 PM

– 8 –
Optional service (Caller ID)
If you subscribe to a Caller ID service, you can:
– display caller information
012345
TG7301_7321MB(e)_QG.fm Page 8 Thursday, May 22, 2008 3:56 PM